• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.124-125
• /
• 2005

ZnS:Mn thin films have attracted great interest as electroluminescence devices. In this study, inductively coupled BCl$_3$/Ar plasma was used to etch ZnS:Mn thin films. We obtained the maximum etch rate of ZnS:Mn thin films was 2209 ${\AA}$/min at a BCl$_3$(20%)/Ar(80%) gas mixing ratio, an RF power of 700 W, a DC bias voltage of-250 V, a total gas flow of 20 sccm, and a chamber pressure of 1 Pa. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Journal of Electrochemical Science and Technology
• /
• 제11권4호
• /
• pp.406-410
• /
• 2020

Despite a simple preparation of manganese oxide (MnO₂) nanowires by electrodeposition, the improvement in specific capacitance (C_sp) and voltammetric response of the MnO₂ nanowire-based electrodes has been quite limited. This is attributed to the poor electrical conductivity of MnO₂ and its dense bulk morphology due to the aggregation of the nanowires. This study investigated the capacitive performance of MnO₂ nanowires electrodeposited on agarose thin films. The good ionic conductivity and porous network of the agarose film provided favorable growth conditions for the MnO₂ nanowires with suppressed aggregation. A maximum C_sp value of 686 F/g measured at a scan rate of 10 mV/s was obtained, which was significantly larger than that of 314 F/g for the agarose-free MnO₂ electrode at the same scan rate. The rate capability was also improved. The C_sp measured at a high scan rate of 100 mV/s retained 74.0% of the value measured at 10 mV/s, superior to the retention of 71.1% for the agarose-free MnO₂ electrode.

• Journal of Korean Vacuum Science & Technology
• /
• 제4권3호
• /
• pp.68-72
• /
• 2000

We have deposited Mn on Pd(oon) at RT up to 30 ML. LEED pattern changed from p($1{\times}1$) to c($2{\times}2$) order below 0.5 ML Mn deposition. During Mn deposition, we have not found any changes in the peak position and the intensity of LEED I/V curve. Using LEED I/V curve analysis for each coverage, we found atomic structure and surface composition of c($2{\times}2$) ordered Mn alloy on Pd(001) surface. Above 1 Ml Mn, in the first layer the Mn subplane lies above the Pd subplane by 0.32 ${\AA}$. This result is very different from the earlier result of Jona et al., who contended that after annealing at 200 for 2 min, a buckled first layer with the Mn subplane lower than the Pd subplane by 0.2 ${\AA}$.

• Journal of Information Processing Systems
• /
• 제8권4호
• /
• pp.603-620
• /
• 2012

Proxy Mobile IPv6 (PMIPv6) is a network-based mobility support protocol and it does not require Mobile Nodes (MNs) to be involved in the mobility support signaling. In the case when multiple interfaces are active in an MN simultaneously, each data flow can be dynamically allocated to and redirected between different access networks to adapt to the dynamically changing network status and to balance the workload. Such a flow redistribution control is called "flow mobility". In the existing PMIPv6-based flow mobility support, although the MN's logical interface can solve the well-known problems of flow mobility in a heterogeneous network, some missing procedures, such as an MN-derived flow handover, make PMIPv6-based flow mobility incomplete. In this paper, an enhanced flow mobility support is proposed for actualizing the flow mobility support in PMIPv6. The proposed scheme is also based on the MN's logical interface, which hides the physical interfaces from the network layer and above. As new functional modules, the flow interface manager is placed at the MN's logical interface and the flow binding manager in the Local Mobility Anchor (LMA) is paired with the MN's flow interface manager. They manage the flow bindings, and select the proper access technology to send packets. In this paper, we provide the complete flow mobility procedures which begin with the following three different triggering cases: the MN's new connection/disconnection, the LMA's decision, and the MN's request. Simulation using the ns-3 network simulator is performed to verify the proposed procedures and we show the network throughput variation caused by the network offload using the proposed procedures.

• 열처리공학회지
• /
• 제4권4호
• /
• pp.15-23
• /
• 1991

The damping capacities of the nonthermoelastic bcc type lath martensite and of the nonthermoelastic hcp type thin plate martensite in Fe-Mn alloys were studied. Fe-17%Mn alloy showing the hcp type thin plate martensite was superior to Fe-4%Mn alloy having the bcc type lath martensite in damping capacity. The damping capacity of the Fe-17%Mn alloy became greater with increasing the hcp martensite volume fraction. The damping mechanism of the Fe-4%Mn alloy was well explained by the dislocation model. However, the damping mechanism of the Fe-17%Mn alloy was explained on the basis of austenite/martensite interface moving model. The two alloys showed almost same levels of tensile strength. However, the elongation was greater in the Fe-17%Mn alloy than in the Fe-4%Mn alloy, showing lower yield strength in the former than in the latter. This result was considered to be attributed to formation of stress-induced martensite during tension test.

• 대한금속재료학회지
• /
• 제50권6호
• /
• pp.419-425
• /
• 2012

The purpose of this research was to develop a low Ni austenitic cast iron through replacing Ni by Cu and Mn because they are cheaper than Ni. The effect of the Cu content (6-12 wt%) on the microstructure characteristics was investigated in Fe-3%C-16%(Ni+Cu+Mn) cast iron. Contrary to general effect of the Cu on cast iron, the result of the microstructure analysis indicated that bainite and cementite were formed in high Cu content (>8 wt%Cu). A crystallized Cu-solution (Cu-Mn) phase and MnS in the Cu-solution were formed. The quantity of those phases increased as the Cu content increased. Consequently, the high Cu content in the composition ratio (Ni+Cu+Mn=16%) caused the formation of Cu-Mn/MnS and those phases decreased the effect of Cu and Mn on austenite formation. For this reason, bainite and cementite were formed in high Cu content.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권1호
• /
• pp.92-95
• /
• 2014

In this work we have synthesized ZnS:Mn nanocrystals (NCs) using a simple one step thermochemical method. $Zn(NO_3)_2$ and $Na_2S_2O_3$ were used as the precursors and $Mn(NO_3)_2$ was the source of impurity. Thioglycolic acid (TGA) was used as the capping agent and the catalyst of the reaction. The structure and optical property of the NCs were characterized by means of X- ray diffraction (XRD), HRTEM, UV-visible optical spectroscopy and photoluminescence (PL). X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses demonstrated cubic phase ZnS:Mn NCs with an average size around 3 nm. Synthesized NCs exhibited band gap of about 4 eV. Photoluminescence spectra showed a yellow-orange emission with a peak located at 585 nm, demonstrating the Mn incorporation inside the ZnS particles.

• Journal of Radiation Protection and Research
• /
• 제12권2호
• /
• pp.19-27
• /
• 1987

황산망간 용액조장치의 $^{56}Mn\;{\gamma}$선 검출효율을 결정하는데 $^{56}Mn$용액의 방사능을 절대측정하는 것은 필수적이다 $^{56}Mn$시료를 제작하기 위하여 99.99%의 순도를 갖는 Mn금속조각 13.718mg되는 시료를 한국에너지연구소 TRIGA MARK-II 원자로의 중성자선속이 약 $10^{13}n/cm^2{\cdot}s$되는 열중성자장에서 12분간 조사시켰다. 중성자 방사화된 $^{56}Mn$금속시료를 0.1N-HCI 용액 50ml 용해시켜서 $^{56}Mn$시료를 제작하여 $4{\pi}{\beta}-{\gamma}$ 동시계수기술로 방사능을 측정한 결과 불확도 0.366%를 갖는 값으로서 1987년 10월 15일 0 시를 기준하여 408.070kBq/mg을 얻었다.

• 한국재료학회지
• /
• 제16권9호
• /
• pp.584-591
• /
• 2006

To enhance the machinability of the austenite stainless alloys, Mn and S were added to form MnS in the austenite matrix. Recently, Ca is also added to increase machinability. The alloying elements, such as C, Mn, S, Ca, and Al, are known to affect machinability, but those roles are not well understood. In this study, the ingots, controlled of alloying elements, C, Mn, S, Ca, Al, were prepared in the 304 stainless steel. The relationship between microstructure and machinability was compared to understand the role of alloying elements. It was proved that Mn and S enhanced machinability but C reduced it by analyzing cutting force on machining in the lathe. The alloying elements, Ca and Al, made a complex oxide compound of Mn-S-Ca-Al-Si-O, which results in increasing tool life. The ferrite volume fraction was changed with alloying elements and the effect of the ferrite fraction on machining was also discussed.

• Current Applied Physics
• /
• 제18권11호
• /
• pp.1190-1195
• /
• 2018

By employing soft X-ray magnetic circular dichroism (XMCD), soft X-ray absorption spectroscopy (XAS), and photoemission spectroscopy (PES), we have investigated the electronic structure of the candidate zero-moment half-metallic $Mn_3Ga$. We have studied the ball-milled and annealed $Mn_3Ga$ powder samples that exhibit nearly zero magnetization. Mn 2p XAS revealed that Mn ions in $Mn_3Ga$ are nearly divalent for both of the Mn ions having the locally octahedral symmetry and those having the locally tetrahedral symmetry. The measured Mn 2p XMCD spectrum of $Mn_3Ga$ is very similar to that of ferrimagnetic $MnFe_2O_4$ having divalent Mn ions. The sum-rule analysis of the Mn 2p XMCD spectrum shows that both the spin and orbital magnetic moments of Mn ions in $Mn_3Ga$ are negligibly small, in agreement with the nearly compensated-ferrimagnetic ground state of $Mn_3Ga$. The valence-band PES spectrum of $Mn_3Ga$ agrees well with the calculated density of states, supporting the half-metallic electronic structure of $Mn_3Ga$.