• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.2
• /
• pp.268-274
• /
• 1998

The traditional kanjang has been prepared by mixing meju and 18% saline solution, and fermenting for 60 days. The traditional kanjang is very salty and inferior in flavor and taste comparing with commercial fermented soy sauce. To improve the quality of traditional kanjang, Zygosaccharomyces rouxii H-62, a flavor-related mutant, was inoculated during fermentation. It was found that the addition of Z rouxii helped to improve the organoleptic quaity of traditional kanjang. The optimal condition for preparing traditional kanjang was to use 5L of 15.5% saline solution per meju. Meju must be cut into 12 pieces to get a proper total nitrogen and pure extract content. The optimal fermentatin temperature was 3$0^{\circ}C$. The prepared kanjang contained over 0.8% total nitrogen and 6.0% pure extract after 60 days of fermentation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.107-110
• /
• 2009

After inquiring into physical characteristics of using fly ash and alkali solution, it was found that higher pH density is favorable to strength development at early age and the higher the age is, the higher the compressive strength gets. Also, it was found that when there is more addition of activator, the compressive strength is higher. I was shown that more than atmospheric curing, steam curing was favorable for development of compressive strength. When the temperature of curing temperature was higher, most of the compressive strengths were higher. Thus, based on this study, it was understood that environmental-friendly chemically combined concrete using fly ash and alkali solution can be utilized without using cement.

• YAKHAK HOEJI
• /
• v.22 no.4
• /
• pp.238-241
• /
• 1978

A simple and convenient method of detecting N, N-dimethy laniline (D.M.A.) residues in ampicillin trihydrate (A.T.) was established. D.M.A. was extracted by chloroform from the chloroform presaturated N/10-ammonia water solution of A.T. and chromatographed on silica gel G thin layer. Blue spot appeared in 15minutes after spray of 2, 6-dichloroquinonechlorimide solution was compared with the blue spot of reference concomitantly processed. The developing solvent was prepared by mixing equal volume of cyclohexane and chloroform. To quantitate the amount of D.M.A. in A.T., T.L.C. was performed with the Eastmann Chromatogram sheet, then color density was measured by Cosmo Superclick densitometer. The developing solvent at this time was cyclohexane-chlorofonn (3+7) mixture. The peak areas obtained with the amount of D.M.A ranging from 0.05 to 2.0 .mu.g were linear to color density. Better sensitive results would be available with the densitometer equipped with monochromator.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.811-813
• /
• 2008

To see the effect of magnesium on adhesion to natural zeolites, a series of batch tests were performed in this research. Mixed bacteria were sampled from the digestion tank at a local sewage treatment plant in Seoul. Magnesium-zeolites were synthesized by mixing natural zeolites with 0.096 M, 0.24 M, and 0.48 M of MgCl2 solution. For comparison, manganese and trivalent ferric zeolites were also prepared. Two grams of 0.2 mm $\sim$ 0.3 mm sized zeolites(non-treated, Mg, Mn and Fe(III) treated zeolites) and 20 mL of water were mixed in a Corex 25 mL tube. Five milliliters of culture solution including bacteria was added to the tube. The tubes were equilibrated in a shaking incubator at mesophilic temperature $(30{\pm}2^{\circ}C)$. The bacterial concentrations were measured with a Microluminometer (New Horizons 3550i) and total organic carbon (TOC) spectrophotometer (Multi NC-3100).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.865-868
• /
• 2000

It was examined that the relationship between microstructures, electrical properties and crystal structure of (1-x)CaMnO$_3$-xCaTiO$_3$solid solution system which was made by mixing a semiconducting material CaMnO$_3$of low resistance and a dielectric material CaTiO$_3$of high resistance with variable ratios (x=0, 0.1, 0.3, 0.5, 0.7, 0.9, 1.0). As the CaTiO$_3$increased, the resistance, B constant and lattice constant were increased, but the grain size was decreased. On particular, above 50wt% of CaTiO$_3$, the resistance at 2 5$^{\circ}C$ was rapidly increased due to the correlation in connectivity of the lattices between the conductive Mn$^{+4}$ octahedron and the insulative Ti$^{+4}$ octahedron.ron.

• Proceedings of the PSK Conference
• /
• 2003.10b
• /
• pp.142.1-142.1
• /
• 2003

Sensitive and safe method for visualization of DNA in agarose gels using visible dye is described. To improve the sensitivity, we studied a counterion-dye staining method using methyl orange as a counterion-dye which contributes to reduce excessive background staining by indoine blue. Dye concentrations, PH of staining solution, mixing molar ratio of two dyes, and staining times were optimized for the counterion-dye staining. By the staining with a mixed solution of 0.005% indoine blue and 0.00165% methyl orange in 10% ethanol 0.2M sodium acetate, 8 ng of the 3 kb DNA in an agarose gel was detected within 1hr. (omitted)

• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.145-148
• /
• 2012

Spherical silica aerogel powders were fabricated via an emulsion polymerization method from a water glass. A water-in-oil emulsion, in which droplets of a silicic acid solution are emulsified with span 80 (surfactant) in n-hexane, was produced by a high power homogenizer. After gelation, the surface of the spherical silica hydrogels was modified using a TMCS (trimethylchlorosilane)/n-hexane solution followed by solvent exchange from water to n-hexane. Hydrophobic silica wet gel droplets were dried at 80 ℃ under ambient pressure. A perfect spherical silica aerogel powder between1 to 12 ㎛ in diameter was obtained and its size can be controlled by mixing speed. The tapping density, pore volume, and BET surface area of the silica aerogel powder were approximately 0.08 g·cm-3, 3.5 ㎤·g-1 and 742 ㎡·g-1, respectively.

• Journal of Powder Materials
• /
• v.21 no.4
• /
• pp.286-293
• /
• 2014

The electrochemical properties of cells assembled with the $LiNiO_2$ (LNO) recycled from cathode materials of waste lithium secondary batteries ($Li[Ni,Co,Mn]O_2$), were evaluated in this study. The leaching, neutralization and solvent extraction process were applied to produce high-purity $NiSO_4$ solution from waste lithium secondary batteries. High-purity NiO powder was then fabricated by the heat-treatment and mixing of the $NiSO_4$ solution and $H_2C_2O_4$. Finally, $LiNiO_2$ as a cathode material for lithium ion secondary batteries was synthesized by heat treatment and mixing of the NiO and $Li_2CO_3$ powders. We assembled the cells using the $LiNiO_2$ powders and evaluated the electrochemical properties. Subsequently, we evaluated the recycling possibility of the cathode materials for waste lithium secondary battery using the processes applied in this work.

• Korean Journal of Materials Research
• /
• v.15 no.6
• /
• pp.399-407
• /
• 2005

The effect of IN738 additive powder on microstructure and mechanical properties of the wide-gap region brazed with BNi-3 filler metal powder was investigated. The wide-gap brazing was conducted in a vacuum of $2\times10^{-5}torr\;at\;1200^{\circ}C$ with various powder mixing ratios of additive to filler powders. The microstructures of the wide-gap brazed region were analyzed by SEM and AES. The region brazed with only BNi-3 filler metal powder had a microstructure consisted of proeutectic, binary eutectic and ternary eutectic structure, while that brazed with a mixture of IN738 additive powder and BNi-3 filler metal powder had a microstructure consisted of IN738 additive powder, binary eutectic of $Ni_3B-Ni$ solid solution and (Cr, W)B. The fracture strength of the wide-gap brazed region was about 680 MPa regardless of the additive powder mixing ratios. Cracks were initiated at the (Cr, W)B and binary eutectic of $Ni_3B-Ni$ solid solution, and propagated through them in the wide-gap brazed region, which lowered the fracture strength of the region.

• Restorative Dentistry and Endodontics
• /
• v.19 no.2
• /
• pp.409-428
• /
• 1994

Endodontic surgery is performed when conventional endodontic therapy fails or is contraindicated. In such cases, retrograde filling materials including amalgam, composite resin, and various cements have been used. Biocompatibilty and margin sealing ability of retrograde filling materials are important for the long term success of endodontic surgery. In vitro cell culture is frequently used as the method of measuring the biocompatibilty of dental materials. The purpose of this study was to evaluate the cytotoxicity of six kinds of retrograde filling materials including newly developed light curing glass ionomer cements. Each material was mixed according to. the manufacture's instruction and evaluated as : freshly mixed, 24-hour after mixing, and 168-hour after mixing respectively. The elution solution was extracted after 24-hour contact with materials using media. Cytotoxicity was evaluated by direct contact, or elution contact. Test results of radiochromium($^{51}Cr$) release, cell viability using tetrazolium dye (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl dimethyltetrazolium bromide(MTT) test and lactate dehydrogenase(LD) of damaged L929 cells were analyzed. In the $^{51}Cr$ release of direct contact, all experimental retrograde filling materials except amalgam and glass ionomer cement showed increased cytotoxicity compared to control. In the $^{51}Cr$ release of elution solution, the released $^{51}Cr$ was so minimal that it was impossible. to evlauate the cytotoxicity exactly. The elution solutions of glass ionomer cement and IRM showed marked cytotoxicity in MTT test. LD enzyme activity was highest in tests of direct contact with composite, light curing composite, and light curing glass ionomer cement and IRM. Amalgam revealed least cytotoxicity while IRM showed cytotoxicity using all three methods. Composite, light curing composite and light curing glass iomomer cement were cytotoxic in the tests of $^{51}Cr$ release and LD activity. Glass ionomer cement showed cytotoxic effect only in the MTT method. From these results it is suggested that the standardization and optimization of cytotoxicity testing, especially using elution solutions, should be strongly advised.