• Journal of Mechanical Science and Technology
• /
• 제19권7호
• /
• pp.1478-1487
• /
• 2005

A small mixed-type turbine with a diameter of 19.9 mm has been substituted for a rotational part of pencil-type air tool. Usually, a vane-type rotor is applied to the rotational part of the air tool. However, the vane-type rotor has some problems, such as friction, abrasion, and necessity of accurate assembly etc.,. These problems make the life time of the vane-type air tool short, but air tools operated by mixed-type turbines are free of friction and abrasion because the turbine rotor dose not contact with the casing. Moreover, it is assembled easily because of no axis offset. These characteristics are merits for using air tools, but loss of power is inevitable on a non-contacting type rotor due to flow loss, tip clearance loss, and profile loss etc.,. In this study, four different rotors are tested, and their characteristics are investigated by measuring the specific output power. Additionally, optimum nozzle location against the rotor is studied. Output powers are obtained through measured pressure, temperature, torque, rotational speed, and flow rate. The experimental results obtained with four different rotors show that the rotor blade shape greatly influences to the performance, and the optimum nozzle location exists near the mid span of the rotor.

• 한국항공우주학회지
• /
• 제37권9호
• /
• pp.889-898
• /
• 2009

본 연구에 적용된 터빈은 사류형 터빈이며 동익의 외경은 108 mm 이다. 터빈은 1.7-2.0%의 낮은 부분분사율에서 작동하므로 익형은 축류형으로 설계되었으며 2단으로 구성되었다. 분사가 축방향으로 형성된 경우와 반경방향으로 형성된 경우에 따른 성능특성의 차이가 연구되었다. 또한 터빈의 단수에 따른 성능특성도 비교 되었다. 터빈의 작동범위에 따른 비교를 위하여 회전수를 변경하면서 성능평가가 이루어졌을 뿐만 아니라 시스템의 평가를 위하여 총 비토오크가 얻어졌다. 사류형 터빈이므로 축방향으로 분사되는 경우가 반경방향으로 분사되어지는 경우보다는 양호한 성능을 얻었으며, 출구단 동익의 효과는 회전수에 의하여 좌우되지만 축방향 분사터빈 경우에 최대 7.8%의 비토오크 상승의 결과를 보여주었다.

• 대한기계학회논문집B
• /
• 제22권11호
• /
• pp.1591-1602
• /
• 1998

Simple spanwise distribution models of deviation angle and pressure loss coefficient due to the tip leakage flow are formulated for use in association with the streamline curvature method as a flow analysis. Combining these new models with the previous deviation and loss models due to secondary flow, a robust streamline curvature method is established for flow analysis of single-stage, subsonic axial turbines with wide ranges of turning angle, aspect ratio and blading type. At the exit from rotor rows, the flow variables are mixed radially according to a spanwise transport equation. The proposed streamline curvature method is tested against a forced vortex type turbine as well as a free vortex type one. The results show that the spanwise variations of flow angle, axial velocity and loss coefficients at rotor exit are predicted with good accuracy, being comparable to a steady three-dimensional Navier-Stokes analysis. This simple and fast flow analysis is found to be very useful for the turbine design at the initial design phase.

• 한국추진공학회지
• /
• 제27권1호
• /
• pp.37-48
• /
• 2023

본 연구에서는 정상 상태 및 천이 상태에 따른 항공기용 터보팬 엔진의 성능해석 모델링을 수행하였다. 대상 엔진은 Pratt & Whitney 사의 F100-PW-229으로 선정하여 팬, 고압 압축기, 연소기, 고압터빈, 저압 터빈, Mixer, 수축-확산형 노즐 등의 구성품을 모델링하였다. 또한, 이차 유로를 통한 터빈에서의 냉각 효과를 적용하였다. Simulink를 이용하여 터보팬 엔진 성능해석 프로그램을 자체 개발함에 따라 해석의 자유도가 높으며, 엔진 제어기 설계에 활용이 용이한 구성의 성능해석 프로그램을 개발하였다. 개발된 성능해석 프로그램은 상용 프로그램인 GASTURB 해석 결과와의 비교를 통하여 검증하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1998년도 제10회 학술강연회논문집
• /
• pp.13-13
• /
• 1998

A simple model of the tip leakage flow models of the rotor downstream flow is developed, based on Lakshminarayana's theoretical concept on the tip clearance flow and the experimental data published in open literature. And new spanwise distribution models of deviation angle and pressure loss coefficient due to the tip leakage flow are formulated for use in association with the streamline curvature method as a through flow analysis. Combining these new models and previous deviation and loss models due to secondary flow, a robust streamline curvature method is established for flow analysis of single-stage, subsonic axial turbines with wide ranges of turning angle, aspect ratio and blading type. At the exit from rotor rows, the flow variables are mixed radially according to a spanwise transport equation. The proposed streamline curvature method is tested against a forced vortex type turbine as well as a free vortex type one. The results show that the spanwise variations of flow angle, axial velocity and loss coefficients at rotor exit are predicted with good accuracy, being comparable to a steady three-dimensional Navier-Stokes analysis. This simple and fast flow analysis is found to be very useful for the turbine design at the initial design phase.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.515-518
• /
• 2006

This paper presents the friction and wear characteristics of contact type sealing unit for a water turbine of a small hydro-power generation, which Is to stop a leakage of a circulating water from a outside of an impeller to an inside of a rolling bearing. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Vickers hardness and the hardness of silicone carbide of SiC is 714.1 in Vickers hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces aye a dry friction a water film friction and a mixed friction that is contaminated by a dust, silt and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components

• 전기학회논문지
• /
• 제60권4호
• /
• pp.796-800
• /
• 2011

As the increasing integrity of VLSI, the BIST(Built-In Self Test) is used as an effective method to test chips. Generally the pseudo-random test pattern generation is used for BIST. But it requires too many test patterns when there exist random resistant faults. Therefore we propose a mixed test scheme which applies to the circuit under test, a deterministic test sequence followed by a pseudo-random one. This scheme allows the maximum fault coverage detection to be achieved, furthermore the silicon area overhead of the mixed hardware generator can be reduced.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.115-121
• /
• 2008

A core engine for pre-cooled turbojet engines is designed and its component performances are examined both by CFD analyses and experiments. The engine is designed for a flight demonstration of precooled turbojet engine cycle. The engine uses gas hydrogen as fuel. The external boundary including measurement devices is set within $23cm{\times}23cm$ of rectangular cross section, in order to install the engine downstream of the air intake. The rotation speed is 80000 rpm at design point. Mixed flow compressor is selected to attain high pressure ratio and small diameter by single stage. Reverse type main combustor is selected to reduce the engine diameter and the rotating shaft length. The temperature at main combustor is determined by the temperature limit of non-cooled turbine. High loading turbine is designed to attain high pressure ratio by single stage. The firing test of the core engine is conducted using components of small pre-cooled turbojet engine. Gas hydrogen is injected into the main burner and hot gas is generated to drive the turbine. Air flow rate of the compressor can be modulated by a variable geometry exhaust nozzle, which is connected downstream of the core engine. As a result, 75% rotation speed is attained without hazardous vibration and heat damage. Aerodynamic performances of both compressor and turbine are obtained and evaluated independently.

• Tribology and Lubricants
• /
• 제22권6호
• /
• pp.314-319
• /
• 2006

In this paper, the friction and wear characteristics of contact type sealing unit far a water turbine have been presented. The sealing unit for a small hydropower generation is to stop a leakage of circulating water from an outside of an impeller to an inside of a rolling bearing. The friction heating between a seal ring and a seal seat may radically increase a surface temperature in which increase a power loss and wear on the rubbing surface. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Victors hardness and the hardness of silicone carbide of SiC is 714.1 in Victors hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces are a dry friction, a water film friction and a mixed friction that is contaminated by a dust, silt, and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat in primary sealing unit. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components.

• 한국추진공학회지
• /
• 제3권4호
• /
• pp.67-74
• /
• 1999

고체 물체 표면이나 지표면에 초음속 제트가 충돌할 때 발생되는 문제들은 다단 로켓의 분리, 우주공간에서의 도킹, 수직 이/착륙기, 제트 엔진의 배기가스, 가스터빈 블레이드, 지상 로켓 발사 등의 다양한 상황에서 일어나며 이러한 충돌제트의 유동은 아음속과 초음속 혼합영역, 충격파가 교차하는 영역, 팽창파, 난류 전단층 등의 매우 복잡한 구조를 이루고 있는 것으로 알려져 있다. 본 연구에서는 출구마하수 2, 축소-확대형 초음속 노즐을 통해 과소 팽창된 제트가 수직, 경사평판에 부딪힐 때 형성되는 표면압력분포 및 유동가시화 등을 초음속 유동시험장치를 이용하여 연구하였다. 평판에서의 최대압력은 수직일 경우보다 경사졌을 때 훨씬 더 컸으며, 이는 여러 충격파를 통한 압력 회복 때문이다. 또한, 평판이 자유제트의 첫 번째 충격파 셀 내에 위치할 때 과소 팽창비에 따른 표면압력분포는 서로 유사한 경향을 보여주었다.