• 비파괴검사학회지
• /
• 제19권5호
• /
• pp.340-346
• /
• 1999

액체/고체 경계면에 표면파가 발생할 때 나타나는 최소반사 및 후방복사 현상을 이용하여 brass와 aluminum 시편 그리고 copper/stainless steel, nickel/brass, nickel/aluminum 도금시편에 대한 표면 탄성파 속도의 주파수 의존성이 측정되었다. 측정된 속도의 분산관계는 일반화 램 표면파의 분산 특성과 잘 일치하였다. 시편들의 분산 특징에 따라 최소반사와 후방복사에 의해 결정된 속도 차이의 경향이 다르게 나타났다. 이러한 대응 관계는 두 현상의 생성 메커니즘과 군속도의 도입으로 설명되었다.

• 한국안전학회지
• /
• 제5권1호
• /
• pp.41-48
• /
• 1990

In this study the explosion characteristics of terephtalic acid dust(PTA) was investigated with the Hartmann type apparatus. The minimum ignition energy, minimum explosible concentration, flame propagation velocity, explosion pressure, explosion pressure rise rate and the effect of inert dust(talcum) on explosion characteristics were measured. Flame velocity was 50m/s at 700g/m$^3$ concentration, and the explosion pressure and explosion pressure rise rate were most likely with that of gas explosion. It was found that an inert dust acts as a heat sinker and it disturbs the combustion of flammable dust, as a result, explosion pressure and explosion pressure rise rate were decreased and minimum explosion concentration was increased with increasing the fraction of talcum dust in PTA.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.364-373
• /
• 2001

This paper describes the variation of lubricant's temperature effects on elastohydrodynamic lubrication. The Newton-Raphson technique was used to solve the simultaneous system of Reynolds and elasticity equations. To show effects of lubricant's temperature, average temperature across the oil film was calculated using the energy equation. Pressure distribution, film shape, and temperature distribution were obtained for fully flooded conjunctions, and various dimensionless speed parameters while load and material parameters were held constant. Minimum film thickness were obtained for various material properties while load and velocity were held constant. It is drawn that the thermal effects have a strong influence on a minimum film thickness under high rolling velocity and slip ratio.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 B
• /
• pp.826-829
• /
• 1995

In this paper, the problem of minimum-time trajectory planning of a robot manipulator with an arbitrary path is dealt. As for a straight path, the trajectory planning can be done without difficulty since the path is easily parameterized by its length. However, this is not the case for a non-straight path. In this paper, by noting that the others' joint angles and velocities are determined if one joint's angle and velocity are known, we reduce the problem of trajectory planning on a non-straight path to one in the 2-dimensional space of one joint's angle and velocity. Then, by applying the dynamic programming, we achieve the minimum-time trajectory planning. A simulation is done for verifying this.

• 환경위생공학
• /
• 제11권1호
• /
• pp.39-44
• /
• 1996

The pressure fluctuations in a gas-solid fluidized bed has been analysed using s statistical method interpreting fluidized 냥d behavior. The performing statistical a analysis of the pressure fluctuations in a fluidized bed of 6.7cm-ID. using uniform p particle size of 115 to $1015{\mu}m$ in diameter. The fluidized gas used air(velocity 0.1~1.2m/sec) at settled bed height to diameter ratios which is LlD=l.O. Then, the pressure fluctuations measured by DPT(differantial pressure transducer). The measuring characteristic values of pressure fluctuation were the mean value and standard value, and also, it has been found that the standard deviation of the pressure fluctuations can be effectively used to predict minimum fluidizing velocity and to explain the fluidized phenomena.

• 한국가스학회지
• /
• 제19권3호
• /
• pp.25-31
• /
• 2015

본 연구에서는 부유 Mg분진의 최소발화온도(MIT)에 있어서 입자 체류시간이 어떠한 영향을 주는지를 실험자료와 입자속도의 계산결과를 사용하여 조사하였다. 평균입경이 증가하면 Mg분진의 MIT는 증가하는 반면에 입자 체류시간(Residence time)은 지수함수적으로 감소하여 분진의 발화 가능성이 저하되는 요인이 될 수 있음을 계산을 통해 확인할 수 있었다. 또한 온도증가에 의한 입자속도에의 영향은 평균입경이 클수록 미세하지만 증가하는 결과가 얻어졌다.

• 한국항공우주학회지
• /
• 제44권3호
• /
• pp.195-202
• /
• 2016

대중적인 연에는 방패연과 가오리연 두 종류가 있다. 방패연은 전문가들에게 널리 사랑 받고 있는 반면, 초보자들에게는 가오리연이 더 익숙하다. 가오리연의 세 종류의 제품들에 대하여 목줄의 매듭을 조사하였다. 가오리 연에 작용하는 공기역학적 힘들을 Fluent를 사용하여 수치적으로 계산하였다. 각 종류의 매듭에 대한 비행 시뮬레이션을 수행함으로써, 기존보다 최소요구풍속이 더 낮은 새로운 매듭을 제안하였다. 최소요구풍속은 연이 날기 시작하는 한계 풍속이다.

• 설비공학논문집
• /
• 제2권4호
• /
• pp.288-294
• /
• 1990

A study has been conducted experimentally on heat transfer characteristics of louvered fin heat exchangers with various fin spacings in air. The experimental results are as follows; 1. Mean heat transfer coefficient is increased with increasing air velocity and the optimum fin spacing shows at S=5mm. 2. Pressure drop is increased with increasing air velocity and its maximum value shows at S=3.5mm and its minimum value shows at S=6mm. 3. $\bar{h}/{\Delta}P$ is decreased with increasing air velocity and its maximum value shows at S=5mm and its minimum value shows at S=3.5mm.

• 한국군사과학기술학회지
• /
• 제21권1호
• /
• pp.1-9
• /
• 2018

In this paper, we have proposed a prediction method for sabot-trajectory of projectile using high speed camera data analysis. Through analyzing trajectory of sabot with high speed camera data, we can extract its real velocity and acceleration including effects of friction force, pressure of flume, etc. Using these data, we suggest a prediction method for sabot-trajectory of projectile having variable acceleration, especially for minimum and maximum acceleration, by using interpolation method for velocity and acceleration data of sabot. Also we perform the projectile launching tests to achieve the trajectory of sabot in case of minimum and maximum thrust. Simulation results show that they are similar to real tests data, for example velocity, acceleration and the trajectory of sabot.

• Elastomers and Composites
• /
• 제57권4호
• /
• pp.147-156
• /
• 2022

In this study, we chose a flat die to optimize a general die geometry. The optimization was aimed at obtaining a uniform velocity distribution across the exit of the die. For the optimization, the input and output design parameters were randomly computed, and response surfaces were generated to obtain statistical data for the minimum and maximum sensitivities computed during optimization. Subsequently, object functions with constraints were numerically computed to obtain the minimum errors in the velocity difference (i.e., variable "Outp" in this study). Finally, we obtained the candidate optimized dataset. Note that the current numerical computations were simultaneously conducted for an entire extruder, i.e., screw plus die. The numerical outlet velocity distributions in the modified die geometry tended to be much more uniform than the conventional distributions in the current optimization processes for this specific flat die.