• Resources Recycling
• /
• v.8 no.4
• /
• pp.11-19
• /
• 1999

Fly ash generated from (he pulverized coal power plant have caused the serious ocean pollution due to the disposal in the ash pond, the life reduction of a power plant and the waste of re-utilizable resource The research to reuse the unburned carbon and mineral composing of the ash has been progressed. In this study. the physical and chemical characteristics of high grade ash and unburned carbon particles obtained from countercurrent column flotation are investigated. The cleaned ash of the less 0,5% loss on Ignition(LOI) in carbon content is a spherical sphere and 39.8${\mu}m$ in size of MMD(Mass Median Diameter). 2.22 $m^2/g$ of specific area. The morphology of high LOI carbon particles is a amorphousness, 76.6 ${\mu}m$ of particle size and 15.2 $m^2/g$ of specific The high grade cleaned ash and the high LOI ash have some difference in the light of physical. chemical and morphological characteristics

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.4
• /
• pp.357-365
• /
• 2010

Optically stimulated luminescence (OSL) of quartz is commonly applied to the age dating of Quaternary sediments. However, one of the issues is that some of the quartz samples are not suitable to OSL dating. Mineralogical analysis of the quartz samples with diverse OSL signals are required to strengthen the reliability and applicability of the OSL dating. We analysed the OSL signal characteristics of sedimentary quartz samples from diverse geological environments and measured their trace element contents using laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). Quartz samples could be grouped into ones suitable to OSL dating and ones unsuitable on the basis of their OSL signal characteristics. The average trace element contents ranged from 73 to 260 ppm (Al), and from 61 to 248 ppm (Ti) with minor Li, Mg, Cr, Mn, and Fe contents below 40 ppm. We did not find any significant variation of trace element contents of quartz samples consistent with their OSL signal characteristics. This indicates unknown mineralogical factors causing diverse OSL characteristics which should be confirmed by further analysis of sufficient set of samples.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7729-7735
• /
• 2015

As plastic injection mold parts is suitable system mass production making mold. So thick steering wheel parts is desirable to carry out gas injection molding. Gas injection mold is skill to inject nitrogen gas postfilling melting raw material into mold. Gas injection mold have many advantage like retrenchment of material cost, upgrading the guality. etc. It was decided gate position to minimize warpage of parts analysis injection mold process using mold flow software and incase doing gas injection mold using normal p.p material. it occur big warpage. so it is object minimizing warpage of injection parts to change p.p material containing mineral 18% and removing fingering phenomenon trouble as changing gate position. Also in case carrying out gas injection mold, I did comparison and analysis to grasp shape flow in gas setting a standard gate after flowing in raw material. Through this study, I found out changing of thickness by parts shape and it can occur warpage of parts by plastic material even though it carry out gas injection mold and it had a direct influence on trouble of parts by gate position.

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.4
• /
• pp.327-337
• /
• 2007

Mineral compositions were determined using quantitative X-ray diffraction analysis on the three kinds of Youngdong illite consisting of white, yellow and refined yellow samples. Mean particle size and their size distribution patterns were measured by laser particle size analyzer. The characteristics of phosphate adsorption on illite were studied through batch adsorption experiments. The white illite has less illite content, but is finer than that of yellow. The refined yellow illite has more illite content and finer particle size compared with those of raw yellow illite. The adsorption rate of phosphate generally increases when the mass of illite increases, whereas adsorption quantity decreases with ascending pH. The phosphate adsorption usually increases with ascending illite content or descending particle size. Although the white illite has lower illite content than the yellow, the former has higher phosphate adsorption quantity than the latter. This can be ascribed to the fine particle size, high interlayer charge, and low substitution in tetrahedral site of white illite. The adsorption isotherms of white illite are well fitted with the Langmuir equation, however those of yellow one are better with Freundlich equation.

• Journal of Nutrition and Health
• /
• v.37 no.3
• /
• pp.193-201
• /
• 2004

The objective was to evaluate the factors influencing on the growth of children aged 3 - 6 years by mini dietary assessment and anthropometric indices in 556 children and by analyzing mineral contents of hair from 273 children by inductively coupled plasma mass spectrometry (ICP-MS). The mean concentration of zinc (Zn) in hair was 68.9 $\pm$ 31.1 ppm and the zinc level of 91 ％ children was less than 60％ of the reference value of 180 ppm. The mean content of lead (Pb) in hair was 1.76 $\pm$ 1.20 ppm, but only 67％ of 273 children was within the reference value of 2 ppm and the lead level of 33％ of children was 2 - 4 times higher than the reference value. The level of Zn was negatively correlated with Pb content (r = -0.305, p 〈 0.01). Hair Zn content, regardless of age, was significantly positively correlated with height (r = 0.214) and body weight (r = 0.159). The height of 95.3％ children was belonged to the normal range of 90 - 109.9％ of standard value and the body weight of 49.8％ children was in the range of 90 - 109.9％ of standard value. However, 8.1 ％ children was overweighted (110 - 119.9％ of standard) and 9.4％ children was obese (120 - 149.9％ of standard) and 0.9％ children was severe obese (〉 150％) which resulted in total 10.3％ obese. Contrary to our expectation, 32.8％ children was underweight (70 - 89.9％ of standard) and 36％ of the underweight children showed the low content of zinc (10 - 49 ppm) in hair. There was no significant correlation between dietary intake of Zn and hair Zn content. Hair Zn content was low even though children consumed greater than 75％ of their requirement for zinc. Regardless of dietary intake of Zn, hair Zn level was rather negatively correlated to the content of Pb in hair. 38.8％ children had an unbalanced diet which resulted in lower intake of calorie, Ca, Zn, vitamin B$_2$ compared with those consuming variety of foods. Therefore, it would be needed that new approach for nutrition education to improve eating habit having the unbalanced diet in preschool children. It might be also suggested to develop new food products to complement the nutrients of Zn, Ca, Fe as snacks or dietary supplement for Korean preschool children.

• Clean Technology
• /
• v.25 no.3
• /
• pp.206-222
• /
• 2019

Recently, various multiphase flows have been developed, and among them some models have been commercialized. However, most of them have been developed based on a pressure-based approach; therefore, various numerical difficulties were involved inherently. Accordingly, in order to overcome these numerical difficulties, a multiphase flow model, MultiPhaSe flow (MPS), following a fractional-flow based approach was developed. In this study, by combining a contaminant transport module describing an enhanced dissolution effect of a surfactant with MPS, a MultiPhaSe flow and TranSport (MPSTS) model was developed. The developed model was verified using the analytical solution of Clement. The MPSTS model can simulate the process of surfactant enhanced aquifer remediation including interphase mass transfer and contaminant transport in multiphase flow by using the coupled particle tracking method and Lagrangian-Eulerian method. In this study, a surfactant was used in a non aqueous phase liquid (NAPL) contaminated area, and the effect of hydro-geological heterogeneity in the layered media on remediation efficiency was studied using the developed model. According to the numerical simulation, when hydraulic conductivity in a lower layer is 10 times, 20 times, and 50 times larger than that in an upper layer, the concentration of dissolved diesel in the lower layer is much higher than that in the upper layer because the surfactant moves faster along the lower layer owing to preferential flow; thus, the surfactant enhances dissolution of residual non aqueous phase liquid in the lower layer.

• Journal of Life Science
• /
• v.29 no.10
• /
• pp.1126-1135
• /
• 2019

From a sample of bamboo byproduct, the protease-producing yeast strain CO-1 was newly isolated. Strain CO-1 is spherical to ovoid in shape and measures $3.1-4.0{\times}3.8-4.4{\mu}m$. For the growth of strain CO-1, the optimal temperature and initial pH were $30^{\circ}C$ and 4.0, respectively. The strain was able to grow in 0.0-15.0%(w/v) NaCl and 0.0-9.0%(v/v) ethanol. Based on a phylogenetic analysis of its 18S rDNA sequences, strain CO-1 was identified as Pichia anomala. The extracellular protease produced by P. anomala CO-1 was partially purified by ammonium sulfate precipitation, which resulted in a 14.6-fold purification and a yield of 7.2%. The molecular mass of the protease was recorded as approximately 30 kDa via zymogram. The protease activity reached its maximum when 1.0%(w/v) CMC was used as the carbon source, 1.0%(w/v) yeast extract was used as the nitrogen source, and 0.3%(w/v) $MnSO_4$ was used as the mineral source. The protease revealed the highest activity at pH 7.0 and $30^{\circ}C$. This enzyme maintained more than 75% of its stability at a pH range of 4.0-10.0. After heating at $65^{\circ}C$ for 1 hr, the neutral protease registered at 60% of its original activity. The protease production coincided with growth and attained a maximal level during the post-exponential phase.

• Analytical Science and Technology
• /
• v.34 no.1
• /
• pp.23-35
• /
• 2021

In order to measure the volatile organic compounds (VOCs) of a sample which is too large to use commercially available chamber, a stainless steel vacuum chamber (VC) (with an internal diameter of 205 mm and a height of 50 mm) was manufactured and the temperature of the chamber was controlled using an oven. After concentrating the volatiles of the sample in the chamber by helium gas, it was made possible to remove residual volatile substances present in the chamber under reduced pressure ((2 ± 1) × 10-2 mmHg). The chamber was connected to a purge & trap (P&T) using a 6 port valve to concentrate the VOCs, which were analyzed by gas chromatography-mass spectrometry (GC-MS) after thermal desorption (VC-P&T-GC-MS). Using toluene, the toluene recovery rate of this device was 85 ± 2 %, reproducibility was 5 ± 2 %, and the detection limit was 0.01 ng L-1. The method of removing VOCs remaining in the chamber with helium and the method of removing those with reduced pressure was compared using Korean drinking water regulation (KDWR) VOC Mix A (5 μL of 100 ㎍ mL-1) and butylated hydroxytoluene (BHT, 2 μL of 500 ㎍ mL-1). In case of using helium, which requires a large amount of gas and time, reduced pressure ((2 ± 1) × 10-2 mmHg) only during the GC-MS running time, could remove VOCs and BHT to less than 0.1 % of the original injection concentration. As a result of analyzing volatile substances using VC-P&T-GC-MS of six types of cell phone case, BHT was detected in four types and quantitatively analyzed. Maintaining the chamber at reduced pressure during the GC-MS analysis time eliminated memory effect and did not affect the next sample analysis. The volatile substances in a cell phone case were also analyzed by dynamic headspace (HT3) and GC-MS, and the results of the analysis were compared with those of VC-P&T-GC-MS. Considering the chamber volume and sample weight, the VC-P&T configuration was able to collect volatile substances more efficiently than the HT3. The VC-P&T-GC-MS system is believed to be useful for VOCs measurement of inhomogeneous large sample or devices used inside clean rooms.

• Journal of Korean Neurosurgical Society
• /
• v.65 no.1
• /
• pp.96-106
• /
• 2022

Objective : The most common complication of anterior cervical discectomy and fusion (ACDF) is cage subsidence and maintenance of disc height affects postoperative clinical outcomes. We considered cage subsidence as an inappropriate indicator for evaluating preservation of disc height. Thus, this study aimed to consider patients with complications such as reduced total disc height compared to that before surgery and evaluate the relevance of several factors before ACDF. Methods : We retrospectively reviewed the medical records of 40 patients who underwent stand-alone single-level ACDF using a polyetheretherketone (PEEK) cage at our institution between January 2012 and December 2018. Our study population comprised 19 male and 21 female patients aged 24-70 years. The minimum follow-up period was 1 year. Twenty-seven patients had preoperative bone mineral density (BMD) data on dual-energy X-ray absorptiometry. Clinical parameters included sex, age, body mass index, smoking history, and prior medical history. Radiologic parameters included the C2-7 cobb angle, segmental angle, sagittal vertical axis, disc height, and total intervertebral height (TIH) at the preoperative and postoperative periods. Cage decrement was defined as the reduction in TIH at the 6-month follow-up compared to preoperative TIH. To evaluate the bone quality, Hounsfield unit (HU) value was calculated in the axial and sagittal images of conventional computed tomography. Results : Lumbar BMD values and cervical HU values were significantly correlated (r=0.733, p<0.001). We divided the patients into two groups based on cage decrement, and 47.5% of the total patients were regarded as cage decrement. There were statistically significant differences in the parameters of measuring the HU value of the vertebra and intraoperative distraction between the two groups. Using these identified factors, we performed a receiver operating characteristic (ROC) curve analysis. Based on the ROC curve, the cut-off point was 530 at the HU value of the upper cortical and cancellous vertebrae (p=0.014; area under the curve [AUC], 0.727; sensitivity, 94.7%; specificity, 42.9%) and 22.41 at intraoperative distraction (p=0.017; AUC, 0.722; sensitivity, 85.7%; specificity, 57.9%). Using this value, we converted these parameters into a bifurcated variable and assessed the multinomial regression analysis to evaluate the risk factors for cage decrement in ACDF. Intraoperative distraction and HU value of the upper vertebral body were independent factors of postoperative subsidence. Conclusion : Insufficient intraoperative distraction and low HU value showed a strong relationship with postoperative intervertebral height reduction following single stand-alone PEEK cage ACDF.

• Journal of Microbiology and Biotechnology
• /
• v.32 no.5
• /
• pp.630-637
• /
• 2022

The objective of this study was to optimize industrial-grade media for improving the biomass production of Weissella cibaria JW15 (JW15) using a statistical approach. Eleven variables comprising three carbon sources (glucose, fructose, and sucrose), three nitrogen sources (protease peptone, yeast extract, and soy peptone), and five mineral sources (K₂HPO₄, potassium citrate, ⳑ-cysteine phosphate, MgSO₄, and MnSO₄) were screened by using the Plackett-Burman design. Consequently, glucose, sucrose, and soy peptone were used as significant variables in response surface methodology (RSM). The composition of the optimal medium (OM) was 22.35 g/l glucose, 15.57 g/l sucrose, and 10.05 g/l soy peptone, 2.0 g/l K₂HPO₄, 5.0 g/l sodium acetate, 0.1 g/l MgSO₄·7H₂O, 0.05 g/l MnSO₄·H₂O, and 1.0 g/l Tween 80. The OM significantly improved the biomass production of JW15 over an established commercial medium (MRS). After fermenting OM, the dry cell weight of JW15 was 4.89 g/l, which was comparable to the predicted value (4.77 g/l), and 1.67 times higher than that of the MRS medium (3.02 g/l). Correspondingly, JW15 showed a rapid and increased production of lactic and acetic acid in the OM. To perform a scale-up validation, batch fermentation was executed in a 5-l bioreactor at 37℃ with or without a pH control at 6.0 ± 0.1. The biomass production of JW15 significantly improved (1.98 times higher) under the pH control, and the cost of OM was reduced by two-thirds compared to that in the MRS medium. In conclusion, OM may be utilized for mass producing JW15 for industrial use.