• 한국토양비료학회지
• /
• 제48권6호
• /
• pp.571-581
• /
• 2015

Soil moisture content is generally accepted as an important factor to understand the process of crop growth and is the basis of earth system models for analysis and prediction of the crop condition. To continuously monitor soil moisture changes at kilometer scale, it is demanded to create high resolution data from the current, several tens of kilometers. In this paper we described a downscaling method for Advanced Microwave Scanning Radiometer 2 (AMSR2) Soil Moisture Content (SMC) from 10 km to 30 m resolution using a soil texture and field measurements that have a high correlation with the SMC. As a result, the soil moisture variations of both data (before and after downscaling) were identical, and the Root Mean Square Error (RMSE) of SMC exhibited the low values. Also, time series analyses showed that three kinds of SMC data (field measurement, original AMSR2, and downscaled AMSR2) had very similar temporal variations. Our method can be applied to downscaling of other soil variables and can contribute to monitoring small-scale changes of soil moisture by providing high resolution data.

• Elastomers and Composites
• /
• 제57권4호
• /
• pp.181-187
• /
• 2022

CdSe-Mn nanocomposites were synthesized using a microwave method with sodium sulfite (Na₂SO₃), selenium (Se), cadmium sulfate octahydrate (3CdSO₄·8H₂O), ammonia solution (NH₃·H₂O), and manganese (II) sulfate monohydrate (MnSO₄·H₂O). We obtained CdSe-Mn-C₆₀ nanocomposites by calcining CdSe-Mn nanocomposites and fullerene (C₆₀) in an electric furnace at 700 ℃ for 2 h. X-ray diffraction, Raman spectroscopy, and scanning electron microscopy were used to characterize the crystal structures, lattice vibrations, and surface morphologies of the products, respectively. The photocatalytic activities of the CdSe-Mn-C₆₀ nanocomposites were investigated based on the photocatalytic degradations of organic dyes such as BG, MB, MO, and RhB under ultraviolet (UV) irradiation at 254 nm. UV-visible spectrophotometry was used to confirm the degradation process.

• ETRI Journal
• /
• 제46권2호
• /
• pp.323-332
• /
• 2024

Receiver and transmitter monolithic microwave integrated circuit (MMIC) multifunction chips (MFCs) for active phased-array antennas for Ka-band satellite communication (SATCOM) terminals have been designed and fabricated using a 0.15-㎛ GaAs pseudomorphic high-electron mobility transistor (pHEMT) process. The MFCs consist of four-channel radio frequency (RF) paths and a 4:1 combiner. Each channel provides several functions such as signal amplification, 6-bit phase shifting, and 5-bit attenuation with a 44-bit serial-to-parallel converter (SPC). RF pads are implemented on the bottom side of the chip to remove the parasitic inductance induced by wire bonding. The area of the fabricated chips is 5.2 mm × 4.2 mm. The receiver chip exhibits a gain of 18 dB and a noise figure of 2.0 dB over a frequency range from 17 GHz to 21 GHz with a low direct current (DC) power of 0.36 W. The transmitter chip provides a gain of 20 dB and a 1-dB gain compression point (P1dB) of 18.4 dBm over a frequency range from 28 GHz to 31 GHz with a low DC power of 0.85 W. The P1dB can be increased to 20.6 dBm at a higher bias of +4.5 V.

• 공업화학
• /
• 제21권6호
• /
• pp.694-696
• /
• 2010

용액공정을 이용하여 표면에 알킬기를 도입하고, 붕소(boron) 또는 인(phosphorous)으로 도핑된 실리콘 나노 입자를 합성하였다. 나노 입자의 합성 여부 및 입자크기는 핵자기공명분광기(NMR), 적외선분광기(FT-IR), 자외선가시광선분광기(UV-Vis), 인광분광기(PL)를 이용하여 분석하였다. 마이크로웨이브 소결기를 이용하여 표면의 알킬기를 제거하고, 결정성을 갖는 필름을 제작하였다. 필름의 조각은 $200{\mu}m$ 정도의 크기를 가지며 큐빅구조를 가지고 있다는 것을 전자주사현미경(FE-SEM)과 투과전자현미경(FR-TEM)으로 확인할 수 있었다. 필름의 전도도는 도핑 타입을 통해 조절할 수 있었다.

• 한국재료학회지
• /
• 제20권6호
• /
• pp.331-337
• /
• 2010

A highly porous Biphasic Calcium Phosphate (BCP) scaffold was fabricated by the sponge replica method with a microwave sintering technique. The BCP scaffold had interconnected pores ranging from $80\;{\mu}m$ to $1000\;{\mu}m$, which were similar to natural cancellous bone. To enhance the mechanical properties of the porous scaffold, infiltration of polycaprolactone (PCL) was employed. The microstructure of the BCP scaffold was optimized using various volume percentages of polymethylmethacrylate (PMMA) for the infiltration process. PCL successfully infiltrated into the hollow space of the strut formed after the removal of the polymer sponge throughout the degassing and high pressure steps. The microstructure and material properties of the BCP scaffold (i.e., pore size, morphology of infiltrated and coated PCL, compressive strength, and porosity) were evaluated. When a 30 vol% of PMMA was used, the PCL-BCP scaffold showed the highest compressive strength. The compressive strength values of the BCP and PCL-BCP scaffolds were approximately 1.3 and 2MPa, respectively. After the PCL infiltration process, the porosity of the PCL-BCP scaffold decreased slightly to 86%, whereas that of the BCP scaffold was 86%. The number of pores in the $10\;{\mu}m$ to $20\;{\mu}m$ rage, which represent the pore channel inside of the strut, significantly decreased. The in-vitro study confirmed that the PCL-infiltrated BCP scaffold showed comparable cell viability without any cytotoxic behavior.

• 한국전자파학회논문지
• /
• 제17권2호
• /
• pp.101-109
• /
• 2006

본 논문은 광대역, DC to 40 GHz 5-bit MMIC 디지털 감쇠기의 설계 및 측정 결과를 나타내었다. 초광대역 감쇠기는 종래의 Switched-T 감쇠기에 전송 선로를 추가하고 전송 선로의 파라미터를 최적화하여 구현되었다. 고주파에서의 정확한 성능 예측을 위해 Momentum 시뮬레이션을 설계에서 수행하였고, 몬테 카를로 해석법을 적용하여 MMIC 공정 변동에 대한 성능의 안정성을 검증하였다. 감쇠기는 $0.15\;{\mu}m$ GaAs pHEMT 공정을 이용하여 제작하였다. 이 감쇠기는 1 dB의 해상도와 총 23 dB의 감쇠 동작 범위를 가진다. 전체 감쇠 범위와 40 GHz의 대역폭에서 높은 감쇠 정확도를 얻었으며, 20 GHz에서 6 dB 이하의 참조 상태 삽입 손실을 가진다. 전체 감쇠 상태와 주파수 범위에서 감쇠기의 입력단과 출력단 반사 손실은 14 dB 이상이다. 감쇠기의 IIP3는 33 dBm으로 측정되었다.

• 한국산업보건학회지
• /
• 제5권2호
• /
• pp.172-183
• /
• 1995

The airborne concentrations of the welding fumes produced during $CO_2$ arcwelding process at shipbuilding, shiprepairing, container manufacturing and car accessary manufacturing industry were investigated. The effects how much reduced the welding fume were checked when the portable fan was used. The results were as follows; 1.The geometric mean of welding fume concentration in shipbuilding factory was $10.05mg/m^3$. This exposure concentration was higher than other 3 manufacturing industries at 95% confidence level. 2. The sampling filters for welding fume could be digested with acid within 1 hour by microwave oven. The recoveries for investigated metal elements were all over 95%. 3. The optimal wavelength could be selected for the simultaneous analysis of 8 metal elements by ICP(Inductively Coupled Plasma). 4. Noxious gases($O_1,NO_2$) produced during $CO_1$ gas arc welding process were detected that the concentration of ozone($O_1$) was less than 0.01 ppm and that of nitrogen dioxide($NO_2$) was 0.01-0.03 ppm. 5. The geometric mean of welding fume particle diameter was $1.26{\mu}m$ and geometric standard deviation was 1.51 for the counts when particle an analyzer(ELZONE) had been used. 6. When the portable fan had been used,the reduced percent of total welding fume for workers was about 47.8% when portable fan was applied to blow and 71.7% when to exhaust.

• 한국진공학회지
• /
• 제7권3호
• /
• pp.167-272
• /
• 1998

ECR plasma CVD를 이용한 SiOF박막은 낮은 유전상수를 가지고 있으며, 기존의 공정과의 정합성이 우수해 다층배선 공정에 채용이 유망한 재료이지만 수분의 흡수로 인한 유전율의 상승과 후속공정의 안정성이 문제점으로 부각되고 있다. 따라서 본 연구에서는 SiOF박막의 내흡습성과 후속공정에서의 안정성을 향상시키기 위하여 SiOF박막을 증착한 후 후속 산소 플라즈마 처리를 행하였다. SiOF박막은 산소 플라즈마 처리를 수행함으로써 SiOF박막의 밀도가 증가하고, 수분과의 친화력이 강한 Si-F 결합이 감소하는 것이 주요한 원인으로 사료된다. 하지만 플라즈마 처리 시간이 5분 이상으로 증가하면 유전율의 증가가 일어난다. 따라서 본 실험에서는 산소 플라즈마 처리조건이 마이크로파 전력이 700W, 공정 압력이 3mTorr, 기판온도가 $300^{\circ}C$일 경우 플라즈마 처리시간은 3분이 적당한 것으로 생각 된다.

• Korean Chemical Engineering Research
• /
• 제54권3호
• /
• pp.374-379
• /
• 2016

이온성 액체를 보조용매로 이용할 경우 바이오매스로부터 파클리탁셀의 추출 효율은 획기적으로 개선되지만 잔류 이온성 액체로 후속 농축 및 건조에 많은 어려움이 따른다. 따라서 본 연구에서는 공정 효율 향상을 위하여 이온성 액체를 이용한 바이오매스 추출물을 효과적으로 건조할 수 있는 새로운 방법을 개발하였다. 추출물을 물로 전처리하고 추가적으로 세척함으로써 잔류 이온성 액체 제거를 통해 효과적으로 건조할 수 있었다. 물 전처리을 위한 최적의 시료/물 비, 혼합시간 및 추가세척을 위한 최적의 시료/물 비는 각각 1:70 (w/v), 4분, 1:100 (w/v)이었다. 또한 진공 건조보다 마이크로웨이브를 이용한 건조의 경우 건조시간을 9배 정도 단축 가능하여 공정 효율이 획기적으로 개선될 것으로 판단된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.28-28
• /
• 2010

This study realized low-temperature crystallization process of the $Ba_{0.6}Sr_{0.4}TiO_3$ (BST) thin films without thermal damage of substrate using excimer laser annealing (ELA) and structural and electrical characteristics were investigated. The amorphous BST thin films were prepared on Pt/Ti/$SiO_2$/Si substrate by sol-gel method at $250^{\circ}C$. The ELA was carried out using KrF excimer laser which provided excitation wavelength of 248 nm. The beam homogenizing system was used in order to homogenize beam shape of Gaussian fit. The XRD and SEM were used to analyze structural characteristics and the microwave capacitance, dielectric loss and tunability of the BST films were measured by a symmetrical stripline resonator method with shorted end. Consequently, the crystallinity of BST thin films were improved after ELA process and RF tunable capacitor was demonstrated at low temperature below $300^{\circ}C$.