• 한국세라믹학회지
• /
• 제31권4호
• /
• pp.415-419
• /
• 1994

The material constants(the complex permeability and permittivity) of ferrite composite determine its microwave absorbing characteristics. Therefore, in order to improve the microwave absorbing characteristics, it is necessary to control the material constants of the ferrite composite. In this study, the method of improving microwave absorbing characteristics by control of permittivity of ferrite composite which has not satisfying matching condition in C-X band (4 GHz~12.4 GHz) was investigated. It was possible to control the permittivity by adjusting graphite loading ratio in the ferrite composite microwave absorber. It was also concluded that the control of permittivity of ferrite composite is effective method to improve the microwave absorbing characteristics.

• 한국세라믹학회지
• /
• 제42권7호
• /
• pp.449-454
• /
• 2005

A waveguide method is developed to study the materials with relatively large dielectric constants at microwave range. Basically, the method is similar to the previous waveguide methods represented by short-circuit line and transmission/reflection measurement methods. However, the complex permittivity is not determined by the shift in resonance frequencies, but by numerical analysis of measured scattering parameters. In order to enhance microwave penetration into the specimen with relatively large permittivity, a dielectric plate with lower permittivity is employed for impedance matching. The influences of air gap between the specimen and waveguide wall are evaluated, and the corresponding errors are estimated. The propagation of higher order modes is also considered. Experimental results for several reference ceramics are presented.

• 전자공학회논문지A
• /
• 제30A권4호
• /
• pp.11-19
• /
• 1993

The complex permittivity and the linewidth of microwave ferrites are measured using the well known cavity perturbation method. The cavity perturbation method has been widely used for the measurement of complex permittivity and conductivity of low loss magnetic and dielectric materials at microwave frequencies. TT1-2000, TT73-2200, and G-113 samples ordered from Trans-Tech Inc, are tested. TE$_{103}$ and TE$_{106}$ rectangular waveguide cavities are fabricated and the ferrite sample of cylidrical rod and sphere shapes are prepared. The error between the measurement values and the supplier's data is less than 1 percent in case of $\varepsilon$’ and about 10 percent in case of linewidth ($\Delta$H). Worst case error analysis shows that our measured results are well within the error bound calculated from the accuracy specification of the measuring instruments.

• 대한금속재료학회지
• /
• 제50권5호
• /
• pp.389-393
• /
• 2012

Improvement in microwave absorbance has been investigated by insertion of a periodic air cavity in rubber composites filled with magnetic powders. A mixture of $Co_2Z$ hexagonal ferrite and Fe powders were used as the absorbent fillers in silicone rubber matrix. The complex permeability and complex permittivity of the magnetic composites were measured by reflection/transmission technique. In the grid-type magnetic absorbers, the equivalent permeability (${\mu}_{eq}$) and permittivity (${\varepsilon}_{eq}$) are calculated as a function of air volume rate (K) on the basis of effective medium theory. Reduction in the material parameters (especially, dielectric permittivity and magnetic loss) has been estimated with the increase of K. Plotting the ${\mu}_{eq}$ and ${\varepsilon}_{eq}$ on the solution map of wave-impedance matching, wide bandwidth microwave absorbance has been predicted in the magnetic composites with an optimum value of K.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.56-59
• /
• 2002

This paper presents a study on the permittivities of the E-glass fabric/epoxy composite laminates containing carbon black dispersions at microwave frequency. Measurement showed that the complex permittivities of the composites depend strongly on the natures and concentrations of the carbon black dispersion. A new scheme to obtain a mixing law for the estimation of complex permittivity is proposed. The experimental values of the complex permittivities were compared to those calculated. Simultaneously, the complex permittivity of carbon black itself was also calculated by the scheme.

• 한국세라믹학회지
• /
• 제29권4호
• /
• pp.293-297
• /
• 1992

A proper combination of complex permeability and permittivity is necessary to produce the zero-reflection microwave absorber with an impedance matching. Increasing of dielectric permittivity and development of an impedance matching was investigated in ferrite-rubber composite specimens by addition of conducting materials. Graphite powder of high dielectric constant was added to the composite specimens to increase the permittivity. The precise estimation of graphite content to produce the matched-wave-impedance absorber at a given frequency can be made by using the numerically derived solution map of impedance matching. It was suggested that permittivity adjustment is an effective technique to obtained the microwave absorber with both good absorbing properties and small thickness as well.

• 전기학회논문지
• /
• 제56권12호
• /
• pp.2196-2201
• /
• 2007

Materials used at microwave are usually used as a dielectric with a manufacturing purpose of printed circuit boards, etc. Complex permittivity of them can be measured from attenuation constant or propagation constant of a transmission line using a microstrip line with bulk type. But as the technique recently which can manufacture to have complex permittivity and permeability demanded using nonferrous metals for powder-type grows up, we need sensors and methods which can measure characteristics of powder-type materials. So far measuring methods of permittivity and permeability with waveguide or coaxial cable are used but they have faults which have a complex measurement method and are difficult to simultaneously measure permittivity and permeability. In this paper, a simultaneous measuring method of permittivity and permeability with 2-port coaxial cable and a new proposed calculation. The proposed 2-port coaxial cable is designed to be easy to insert materials and to have a wideband. We measure permittivity and permeability of magnetic powder(Ni-Fe-Mo, Ni-Fe) which reveal its characteristic at $0.3{\sim}1.3GHz$ to identify the proposed sensor.

• Composites Research
• /
• 제24권2호
• /
• pp.38-45
• /
• 2011

본 논문에서는 유리섬유 강화 복합재 적층판으로 이루어진 단일층 Dallenbach layer의 전파흡수체의 최적화 기법을 제시하고 그 성능을 분석하였다. 복합재 적층판의 전기적 특성을 제어하기 위해서 탄소나노튜브(CNT)를 혼합한 프리프레그를 사용하였다. 최적화 설계 기법은 유전자 알고리즘을 사용하였으며, 이를 이용하여 다양한 주파수에서 흡수체를 설계하고, 복합재의 두께 및 CNT 함유율을 최적화하였다. CNT 함유율의 최적화를 위해서는 복합재의 복소 유전율의 수치적 모델이 사용되었다. 전파흡수체의 최적설계에서 주파수에 따라서 CNT 함유율은 비례하여 증가하고, 흡수체의 두께는 반비례하여 감소한다. 흡수체의 -10 dB 흡수대역폭은 흡수체가 설계된 중심주파수에 비례하여 증가한다. 설계된 흡수체의 검증을 위해서 10 GHz에서 중심주파수를 갖는 흡수제를 제조하고 그 성능을 평가하였다. 복합재 적층판의 복소 유전율과 전파흡수체의 반사손실은 벡터회로망분석기와 7 mm 동축관을 이용하여 측정하였다. 복합재의 두께와 복소 유전율에 있어서의 측정된 값과 예측치의 차이에 의해서 중심주파수의 이동, 중심주파수에서의 반사손실의 감쇄, 흡수대역폭의 감소가 발생하였다.

• 자원리싸이클링
• /
• 제9권6호
• /
• pp.31-35
• /
• 2000

Mn-Zn ferrite 폐기물을 시멘트와 혼합한 복합전파흡수체를 제작하여 재료정수 및 반사감쇠량을 조사하였다. 지지재로 사용한 시멘트는 실리콘 고무의 재료정수와 비교하여 높은 복소유전율($\varepsilon$=$_{r}$': 7.6, $\varepsilon_{r}$ ": 0.6)을 나타내었고, Mn-Zn ferrite 폐기물과 시멘트의 혼합무게비(F/C)가 증가함에 따라 복소유전율은 감소하였고, 복소투자율은 증가하였다. 최대반사감쇠량을 나타내는 주파수는 F/C가 1에서 3으로 증가함에 따라 2.7 GHz에서1.3 GHz로 감소하였고, 정합두께는 8.7 mm에서 12.7 mm로 증가하는 경향이 나타났다. 모든 시편에서 최대반사감쇠량은 -40 dB 이상으로 Mn-Zn ferrite 폐기물을 전파흡수체로 활용이 가능하다.

• Journal of electromagnetic engineering and science
• /
• 제1권2호
• /
• pp.139-145
• /
• 2001

In this paper, a coaxial sample holder is proposed with its de-embedding and parameter extraction procedure. The S-parameters were measured up to 1 GHz using network analyzer, HP8753D, and N-type connector together with the de-embedding of N-type connector. The proposed de-embedding procedure is performed to extract electrical parameters of blood glucose, which gives the permittivity of blood glucose. We also analyzed the error of extracted parameters, which are caused by instrument error and geometrical error. Using these error analyses, we reduced the error factors of extracted parameters. We extracted electrical parameters of glucose samples through these all extraction procedure and confirmed the possibility of glucose diagnosis system based on microwave system.