• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.113-120
• /
• 2006

This thesis deals with solutions such as coverage area extension, reduction of the shadow region and performance enhancement of handover caused by structural modification of WiBro network. The More far the distance of RAS(Radio Access Station) and SS(Subscriber Station) is in micro cell, the more bad the quality of channel environment becomes owing to radio interference. Consequently, it causes the deterioration of the throughput and also the deterioration of communication quality in many sides. In fact, most users of WiBro are located in the region, the QPSK region which is bad in point of channel quality. It brings the service complaint by user. We select RS(relay station) to solve the matter caused by channel environment in this cell, and extend coverage and improve the performance of handover call blocking.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.56-63
• /
• 2016

This paper presents a novel method for detecting a ghost key at the membrane type keyboard, which has additional resistive coating to the membrane film. Also, the optimal ratio of resistances for detecting a ghost key was designed based on the characteristics of the membrane film. The optimal ratio of resistances was considered to be able to detect the worst case (i.e., difference voltage between normal key and ghost key is minimum). The ability of the proposed methods are evaluated by simulation studies in this paper. In order to verify the proposed method, the experiment was carried out with a designed circuit and A/D (analog to digital) in MCU (micro controller unit). The proposed method is implemented into the membrane type keyboard and is verified by experimental results.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.11
• /
• pp.57-66
• /
• 2004

It is widely accepted that the coverage with high user densities in mobile multimedia environments can only be achieved with small cell such as micro- and pico-cell. The smaller cell size causes frequent handovers between cells and a decrease in the permissible handover processing delay. This may result in the handover failure, in addition to the loss of some packets during the handover. In these cases, re-transmission is needed in order to compensate errors, which triggers a rapid degradation of throughput. In this paper, we propose a new handover scheme in the next generation mobile communication systems, in which the handover setup process is done in advance before a handover request by predicting the handover cell based on mobile terminal's current position and moving direction. Simulation is focused on the handover failure rate and packet loss rate. The simulation results show that our proposed method provides a better performance than the conventional method.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.25 no.3
• /
• pp.299-305
• /
• 2015

Global environmental concerns and the ever increasing need of energy, coupled with steady progress in renewable energy technologies, are opening up new opportunities for utilization of renewable energy resources. Distributed electricity generation is a suitable option for sustainable development thanks to the load management benefits and the opportunity to provide electricity to remote areas. Solar energy being easy to harness, non-polluting and never ending is one of the best renewable energy sources for electricity generation in present and future time. Due to the random and intermittent nature of solar source, PV plants require the adoption of an energy storage and management system to compensate fluctuations and to meet the energy demand during night hours. This paper presents an efficient, economic and technical model for the design of a MPPT based grid connected PV with battery storage and management system. This system satisfies the energy demand through the PV based battery energy storage system. The aim is to present PV-BES system design and management strategy to maximize the system performance and economic profitability. PV-BES (photovoltaic based battery energy storage) system is operated in different modes to verify the system feasibility. In case of excess energy (mode 1), Li-ion batteries are charged using CC-CV mechanism effectively controlled by fuzzy logic based PID control system whereas during the time of insufficient power from PV system (mode 2), batteries are used as backup to compensate the power shortage at load and likewise other modes for different scenarios. This operational mode change in PV-BES system is implemented by State flow chart technique based on SOC, DC bus voltages and solar Irradiance. Performance of the proposed PV-BES system is verified by some simulations study. Simulation results showed that proposed system can overcome the disturbance of external environmental changes, and controls the energy flow in efficient and economical way.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.113.1-113.1
• /
• 2011

PEMS (printed electro-mechanical system) is fabricated by means of various printing technologies. Passive and active compo-nents in 2D or 3D such as conducting lines, resistors, capacitors, inductors and TFT(Thin Film Transistor), which are printed withfunctional materials, can be classified in this category. And the issue of PEMS is applied to a R2R process in the manu-facturing process. In many electro-devices, the vacuum process is used as the manufacturing process. However, the vacuum process has a problem, it is difficult to apply to a continuous process such as a R2R(roll to roll) printing process. In this paper, we propose an ESD (electro static deposition) printing process has been used to apply an organic solar cell of thin film forming. ESD is a method of liquid atomization by electrical forces, an electrostatic atomizer sprays micro-drops from the solution injected into the capillary with electrostatic force generated by electric potential of about several tens kV. ESD method is usable in the thin film coating process of organic materials and continuous process as a R2R manufacturing process. Therefore, we experiment the thin films forming of PEDOT:PSS layer and active layer which consist of the P3HT:PCBM. The organic solar cell based on a P3HT/PCBM active layer and a PEDOT:PSS electron blocking layer prepared from ESD method shows solar-to-electrical conversion efficiency of 1.42% at AM 1.5G 1sun light illumination, while 1.86% efficiency is observed when the ESD deposition of P3HT/PCBM is performed on a spin-coated PEDOT:PSS layer.

• Tribology and Lubricants
• /
• v.30 no.3
• /
• pp.139-145
• /
• 2014

Nowadays, most micro-patterns are manufactured during flow line production. However, a conventional rotary chemical mechanical polishing (CMP) system has a limited throughput for the fabrication of large and flexible electronics. To overcome this problem, we propose a novel linear roll-CMP system for the planarization of large-area electronics. In this paper, we present a statistical analysis on the linear roll-CMP process of copper-clad laminate (CCL) to determine the impacts of process parameters on the material removal rate (MRR) and its non-uniformity (NU). In the linear roll-CMP process, process parameters such as the slurry flow rate, roll speed, table feed rate, and down force affect the MRR and NU. To determine the polishing characteristics of roll-CMP, we use Taguchi's orthogonal array L16 (44) for the experimental design and F-values obtained by the analysis of variance (ANOVA). We investigate the signal-to-noise (S/N) ratio to identify the prominent control parameters. The "higher is better" for the MRR and "lower is better" for the NU were selected for obtaining optimum CMP performance characteristics. The experimental and statistical results indicate that the down force and roll speed mainly affect the MRR and the down force and table feed rate determine the NU in the linear roll-CMP process. However, over 186.3 N of down force deteriorates the NU because of the bending of substrate. Roll speed has little relationship to the NU and the table feed rate does not impact on the MRR. This study provides information on the design parameter of roll-CMP machine and process optimization.

• Journal of Powder Materials
• /
• v.13 no.5 s.58
• /
• pp.321-326
• /
• 2006

Electronic packaging involves interconnecting, powering, protecting, and cooling of semiconductor circuits fur the use in a variety of microelectronic applications. For microelectronic circuits, the main type of failure is thermal fatigue, owing to the different thermal expansion coefficients of semiconductor chips and packaging materials. Therefore, the search for matched coefficients of thermal expansion (CTE) of packaging materials in combination with a high thermal conductivity is the main task for developments of heat sink materials electronics, and good mechanical properties are also required. The aim of this work is to develop copper matrix composites reinforced with carbon nanofibers. The advantages of carbon nanofibers, especially the good thermal conductivity, are utlized to obtain a composite material having a thermal conductivity higher than 400 W/mK. The main challenge is to obtain a homogeneous dispersion of carbon nanofibers in copper. In this paper, a technology for obtaining a homogeneous mixture of copper and nanofibers will be presented and the microstructure and properties of consolidated samples will be discussed. In order to improve the bonding strength between copper and nanofibers, different alloying elements were added. The microstructure and the properties will be presented and the influence of interface modification will be discussed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.6
• /
• pp.525-535
• /
• 2004

In this paper, a two-phase DZRCD(Dual Zero Vector Modes RCD) technique is proposed to develope the problem of a conventional two-phase RCD-PWM (Random Centered Distribution PWM) which gives the power spectra of narrow band range in the high modulation index (M). In the proposed DZRCD technique, the zero vector $V_0$ is selected as $V_0$(111) for M$\geqq$0.8. Also, $V_0$ is selected as $V_0$(000) for the modulation indices < 0.8. For the unplementation of the proposed method, a 16-bit micro-controller Cl67 was used and the experiments were conducted with the 1.5kw induction motor under no load condition. The experimental results show that the voltage / current spectra is spread to a wide band range, and the switching noise of motor is reduced by the proposed method compared to the conventional random operation.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.7
• /
• pp.42-49
• /
• 1989

A new integrated coding method is proposed in this study for embedding the text information including Hangul into an image. A monochrome analog image may be quantized to a few leveled digital image and be displayed on bi-leveled output devices by using halftone processing techniques. Text data are embedded on each micro pattern. Based on this concept, the encoding and the decoding algorithm are implemented and experiments are performed. As a result, the average amount of the embedded text information is more than 8 bpp (bits per pixer) in this halftone processed image converted form a $64{\times}64$ image, i.e, corresponding to 2000 characters in Hangul, or 4000 characters in alphanumeral. using this algorithm, the integrated personal record management system is implemented.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.2 s.332
• /
• pp.39-48
• /
• 2005

An HMIPv6 provides micro mobility management using MAP for decreasing handover delay and network load in a mobile IP networks. An HMIPv6 uses distance based algorithm for MAP selection when a mobile host enters a new network domain. However, since every mobile hosts select a farthest router as a MAP, a handover delay and packet loss will be increased. A new MAP selection scheme is herein proposed to solve the problems caused by the distance based MAP selection algorithm by using secondary MAP. We executed the performance evaluation by simulation about handover delay and packet loss of an HMIPv6 and our proposed scheme. The simulation results show that the performance of our proposed scheme is better than that of HMIPv6.