• 한국정밀공학회지
• /
• 제31권5호
• /
• pp.451-457
• /
• 2014

Surface roughness of mechanical components is an important factor which affects the tribological phenomena. Various surface patterns have been applied to surfaces to improve the tribological characteristics of mechanical components. In this work, the friction reduction effect of micropatterns on silicon was investigated. For this purpose, micro-dimple patterns were fabricated on silicon wafer by DRIE process. In the friction experiments silicone oil was used as lubricant. Also, the lubricant was cleaned to simulate a lubricant depleted condition. In depleted lubricated condition, friction coefficient of micro-pattern specimens was lower than specimens without micro-patterns. It was found that friction reduction effect of micro-pattern could be successfully maintained even after cleaning the lubricant on the surface.

• 대한기계학회논문집A
• /
• 제31권12호
• /
• pp.1139-1143
• /
• 2007

A simple method for the fabrication of 3D micro-nano hybrid patterns was presented. In conventional fabrication methods of the micro-nano hybrid patterns, micro-patterns were firstly fabricated and then nano-patterns were formatted on the micro-patterns. Moreover, these micro-nano hybrid patterns could be fabricated on the flat substrate. In this paper, we suggested the fabrication method of 3D micro-nano hybrid patterns using micro-indentation on the anodized aluminum substrate. Since diameter of the hemispherical nano-pattern can be controlled by electrolyte and applied voltage in the anodizing process, we can easily fabricated nano-patterns of diameter of loom to 300nm. Nano-patterns were firstly formatted on the aluminum substrate, and then micro-patterns were fabricated by deforming the nano-patterned aluminum substrate. Hemispherical nano-patterns of diameter of 150nm were fabricated by anodizing process, and then micro-pyramid patterns of the side-length of $50{\mu}m$ were formatted on the nano-patterns using micro-indentation. Finally we successfully replicated 3D micro-nano hybrid patterns by hot-embossing process. 3D micro-nano hybrid patterns can be applied to nano-photonic device and nano-biochip application.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.1-6
• /
• 2018

Micro prism pattern is applying in order to get increase of luminance, control the light, and so forth especially in optics and display industry. Most patterns are fabricated by lithography, planning, and EDM, but they have limitations on the productivity or the unit cost of produce. However, ultra precision mold is one of the processes able to replace it, and assure high productivity required by industries. In this investigation, micro prismatic end-milling is suggested in order to fabricate the pattern effectively. Micro prism pattern having $100{\mu}m$ of pitch and height was machined on STD-11. After machining, the flank and boundary wear on micro end mill were measured and analyzed, as well as burr formation and dimensional accuracy of fabricated pattern were evaluated. Thus the optimal cutting conditions were derived.

• Korea-Australia Rheology Journal
• /
• 제19권3호
• /
• pp.165-169
• /
• 2007

The light guide plate (LGP) of LCD-BLU (Liquid Crystal Display-Back Light Unit) is usually manufactured by forming numerous dots by etching process. However, the surface of those etched dots of LGP is very rough due to the characteristics of etching process, so that its light loss is relatively high due to the dispersion of light. Accordingly, there is a limit in raising the luminance of LCD-BLU. In order to overcome the limit of current etched-dot patterned LGP, micro-lens pattern was tested to investigate the possibility of replacing etched pattern in the present study. The micro-lens pattern fabricated by the modified LiGA with thermal reflow process was applied to the optical design of LGP. The attention was paid to the effects of different optical pattern type (i.e. etched dot, micro-lens). Finally, the micro-lens patterned LGP showed better optical qualities than the one made by the etched-dot patterned LGP in luminance.

• 한국기계가공학회지
• /
• 제14권3호
• /
• pp.124-130
• /
• 2015

The purpose of this study is to investigate friction characteristics according to micro-dimple patterns. The surface texturing of micro-dimple patterns was tested to examine the friction of pin-on-disk using flat-on-flat contact geometry. The patterns of both dimple circle and groove pattern were adopted to carry out the effect of those ones. In the low loads, such as 13.8N and 27.7N, the friction coefficients of groove pattern were lower than those of dimple circle pattern. In many other comparisons of normal loads, the groove pattern had lower friction forces, which showed the effect of surface texturing. The relationship between sliding time and friction forces showed that the increase of friction forces of groove pattern were relatively lower than those of dimple pattern. In conclusion, the dimple patterns of dimple-circle pattern and groove pattern strongly contributed to reducing the friction between contacting materials.

• 융합보안논문지
• /
• 제14권5호
• /
• pp.17-24
• /
• 2014

본 논문에서는 얼굴 표정 인식을 위한 지역미세패턴(local micro pattern)의 하나인 LBP(Local Binary Pattern) 코드의 잡음에 대한 단점을 해결하기위하여 새로운 미세패턴 방법인 LDP(Local Directional Pattern)를 제안한다. 제안된 방법은 LBP의 문제점을 해결하기 위해 $m{\times}m$ 마스크를 이용하여 8개의 방향 성분을 구하고, 이를 크기에 따라서 정렬한 후 상위 k개를 선정하여 해당 방향을 나타내는 비트를 1로 설정한다. 그리고 8개의 방향 비트를 순차적으로 연결하여 최종 패턴 코드를 생성한다. 실험결과, 제안된 방법은 기존 방법에 비해 회전에 대한 영향이 적으며, 잡음에 대한 적응력이 현저히 높았다. 또한, 제안된 방법을 기반으로 얼굴의 영구적인 특징과 일시적인 특징을 함께 표현하는 새로운 지역미세패턴의 개발이 가능함을 확인하였다.

• 한국기계가공학회지
• /
• 제10권3호
• /
• pp.94-99
• /
• 2011

Micro-scale surface pattern has an benefit of tribological application under lubricated sliding contact. Therefore, a special pattern, that has to reduce the coulomb friction under contact, is considered to be necessary for improved efficiency of machines. The current study investigated the friction property of angle effect for micro-scale grooved crosshatch pattern on bearing steel surface using pin-on-disk type. The samples fabricated by photolithography process and then these are carry out the electrochemical etching process. We discuss the friction property due to the influence of hatched-angle on contact surface. We could be explained the lubrication mechanism for a Stribeck curve. It was found that the friction coefficient depend on an angle of the crosshatch on contact surface. It was thus verified that micro-scale crosshatch grooved pattern could affect the friction reduction.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1537-1541
• /
• 2007

We injection molded a wedge type of plate with micro prizm patterns on its surface and investigated the fidelity of replication of the micro pattern depending on the process parameter such as mold temperature, melt temperature, injection rate or packing pressure. The size of the size of the $90^{\circ}$ prizm pattern is $50{\mu}m$ and the size of the plate is about 300㎜${\times}$200㎜. The thicknesses are 2.6㎜. and 0.7mm at each edge of the wedge type of plate. The fidelity of the replication turned out quite different according to the process parameters and location of the patterns on the plate. We measured the cavity pressure and temperature in real-time during the molding to analyze the effect of the local melt pressure and temperature on the micro pattern replication.

• Design & Manufacturing
• /
• 제17권2호
• /
• pp.22-26
• /
• 2023

As Light-Emitting Diodes(LEDs) continue to advance in performance, their application in automotive lamps is increasing. Automotive LEDs utilize light guides not only for aesthetics but also to control light quantity and direction. Light guides employ patterns of a few hundred micrometers(㎛) to regulate the light, and the surface roughness(Ra) of these patterns can reach tens of nanometers(nm). Given that these light guides are produced through injection molding, mold processing technology with high surface quality micro-patterns is required. This study serves as a preliminary investigation into the development of high surface quality micro-pattern processing technology. It examines the surface roughness of the workpiece based on the cutting direction of the pattern and the cutting fluid type when cutting micro-patterns on STAVAX steel using cubic Boron Nitride(cBN) tools. The experiments involved machining a step-shaped micro-pattern with a height of 60 ㎛ and a pitch of 400 ㎛ in a 22×22 mm area under identical cutting conditions, with only the cutting direction and cutting fluid type being varied. The machining results of four cases were compared, encompassing two cases of cutting direction(parallel to the pattern, orthogonal to the pattern) and two cases of cutting fluid type (flood, mist). Consequently, the Ra value was found to be the highest(Ra 128.33 nm) when machining with the flood type in parallel to the pattern, while it was the lowest(Ra 95.22 nm) when machining with the mist type orthogonal to the pattern. These findings confirm that there is a difference of up to 25.8 % in the Ra value depending on the cutting direction and cutting fluid type.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.107-108
• /
• 2008