• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권2호
• /
• pp.125-131
• /
• 2000

A high resolution Laser Doppler Vibrometer(LDV) developed using electronic fringe counting method. The fringe pattern signal obtained via analog signal processing is divided into two. One was converted to a TTL signal with a ZCD(zero-crossing detector) and then counted to calculate the displacement due to the vibration. The other was directed to the A/D converter to get a high resolution of about $\lambda/320$ with the phase comparison method. The data obtained with the A/D converter was used in the displacement calculation and the result was displayed on a LCD pane. In this study, a Laser Doppler Vibrometer with measurement range of $0.32\mum~129\mum$ and displacement resolution of 2nm, about $\lambda/320$ , was developed. And this LDV can be used to measure the dynamic of microsize devices such as MEMS(Micro Electro-Mechanical Systems) and to diagnose high capacity electric equipment such as circuit breakers and transformers, of which resonant frequencies are changed when they are damaged.

• 지질공학
• /
• 제6권2호
• /
• pp.53-58
• /
• 1996

암석 시료의 파괴시에 발생하는 AE신호를 측정하여 파괴와 관련된 미세균열의 발생원에 대한 연구를 위하여서는 탐촉자에서 기록장치까지 전과정에 대한 검증이 필요하다. 특히 탐촉자는 기계적인 진동을 전기신호로 전환하는 기능을 가진 예민한 장치로서 다양한 인자에 의하여 예민도가 달라질 수 있기 때문에 보정시험을 실리하여야 한다. 압전 압력형 PAC 탐촉자를 NBS나 DG의 변위형 탐촉자에 의하여 보정하는 시험을 실시하였다. NBS 및 PAC탐촉자는 파의 입사방위각에는 무관하나 입사각에는 예민하게 반응한다. 즉, 입사각이 $90^{\circ}$ 일 때에는 입사각 $15^{\circ}$ 이하 일 때보다 약 10배의 큰 출력을 나타내었다. 또한, 시험에 사용된 PAC 탐촉자가의 경우 강도에 대한 개별 예민도의 차이가 최대 약 40%이었다. 압력형 PAC 탐촉자는 변위형 표준탐촉자로 절대치 보정시험을 실시한 결과 보정계수는 평균 77mv/pm이었다.

• 한국유체기계학회 논문집
• /
• 제16권3호
• /
• pp.18-25
• /
• 2013

Recently the requirement of long-term mobile energy source for mobile robot or small-sized unmanned vehicle is highly increased, and the micro turbine generator(MTG) which is known to have high energy and power density is under development. MTG is designed to have air foil bearing and high speed rotor of which operating speed is 400,000rpm. In the development stage of high speed rotor and bearing, stability analysis for the full operational speed range is essential and the dynamic coefficients such as stiffness and damping coefficients of bearing depending on the rotational speed are required for that. Although perturbation method is usually used to identify the dynamic coefficients, it's not easy to give the perturbation to the high speed rotating rotor. In this study, we present the dynamic coefficients measurement system for air foil bearing which consists of electromagnets, gap sensors, high speed motor and controller. This measurement system can exert the sine sweep force to the rotor-bearing, measure the displacement of rotor and get FRF(Frequency response function) of rotor-bearing. The least square estimation method is applied to identify the dynamic coefficients of bearing from the measured frequency response at the different rpm and the identified dynamic coefficients for the wide rotational speed range are presented.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.731-734
• /
• 2005

Generally, characteristics of electromechanical actuators are coupled with the mechanical and the electrical properties. Important mechanical parameters of these actuators are the achievable force and displacement in the presence of electric field. These mechanical parameters are related to the stress and strain of the materials and the actuator geometry. This paper presents how to measure the blocked force by using the micro-balance. The blocked force is defined as the force produced by the transducer under an applied voltage when the tip is constrained to zero motion. Also, a theoretical force by using the cantilever beam model is calculated under elastic domain. From the sample of 4 cm $\times$ 1 cm $\times$ 20 $\mu$m, the blocked farce measured from the equipment is 20.3 $\mu$N at 8 V$_{DC}$. By comparing it with the theoretical value, 24.9 $\mu$N, the blocked force measurement is acceptable. The furce measurement is also investigated with different AC electric fields and the frequency.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.128-135
• /
• 1995

Atomic force microscopy/friction force microscopy (AFM/FFM) techniques are increasingly used for tribological studies of engineering surfaces at scales, ranging from atomic and molecular to microscales. These techniques have been used to study surface roughness, adhesion, friction, scratching/wear, indentation, detection of material transfer, and boundary lubrication and for nanofabrication/nanomachining purposes. Micro/nanotribological studies of single-crystal silicon, natural diamond, magnetic media (magnetic tapes and disks) and magnetic heads have been conducted. Commonly measured roughness parameters are found to be scale dependent, requiring the need of scale-independent fractal parameters to characterize surface roughness. Measurements of atomic-scale friction of a freshly-cleaved highly-oriented pyrolytic graphite exhibited the same periodicity as that of corresponding topography. However, the peaks in friction and those in corresponding topography were displaced relative to each other. Variations in atomic-scale friction and the observed displacement has been explained by the variations in interatomic forces in the normal and lateral directions. Local variation in microscale friction is found to correspond to the local slope suggesting that a ratchet mechanism is responsible for this variation. Directionality in the friction is observed on both micro- and macro scales which results from the surface preparation and anisotropy in surface roughness. Microscale friction is generally found to be smaller than the macrofriction as there is less ploughing contribution in microscale measurements. Microscale friction is load dependent and friction values increase with an increase in the normal load approaching to the macrofriction at contact stresses higher than the hardness of the softer material. Wear rate for single-crystal silicon is approximately constant for various loads and test durations. However, for magnetic disks with a multilayered thin-film structure, the wear of the diamond like carbon overcoat is catastrophic. Breakdown of thin films can be detected with AFM. Evolution of the wear has also been studied using AFM. Wear is found to be initiated at nono scratches. AFM has been modified to obtain load-displacement curves and for nanoindentation hardness measurements with depth of indentation as low as 1 mm. Scratching and indentation on nanoscales are the powerful ways to screen for adhesion and resistance to deformation of ultrathin fdms. Detection of material transfer on a nanoscale is possible with AFM. Boundary lubrication studies and measurement of lubricant-film thichness with a lateral resolution on a nanoscale have been conducted using AFM. Self-assembled monolyers and chemically-bonded lubricant films with a mobile fraction are superior in wear resistance. Finally, AFM has also shown to be useful for nanofabrication/nanomachining. Friction and wear on micro-and nanoscales have been found to be generally smaller compared to that at macroscales. Therefore, micro/nanotribological studies may help def'me the regimes for ultra-low friction and near zero wear.

• 한국정밀공학회지
• /
• 제27권7호
• /
• pp.94-100
• /
• 2010

This paper describes the design and evaluation procedure of an ultra-precision rotary table for freeform generating machined tools. Design of the thrust and journal hydrostatic bearings and experimental evaluation of the table were performed. To get the compact size and less lost motion direct drive servomotor with ultra precision encoder. From the considered design, following performance were confirmed by experiment. The total stiffness of the prototype rotary table was 483.6 $N/{\mu}m$ and 97.6 $N/{\mu}m$ for axial and radial direction, respectively. Rotational accuracy of the table was investigated by capacitive sensor and reversal measurement technique, and 0.10 ${\mu}m$ radial direction and 0.05 ${\mu}m$ axial direction of the rotational accuracy were confirmed. The micro resolution of the table was also investigated with displacement of capacitive sensor, and $0.5/10000^{\circ}$ of micro resolution was confirmed. Index accuracy of the table was evaluated by the autocollimator and polygon mirror, and the $\pm0.39$ arcsec accuracy and $\pm0.16$ arcsec repeatability of the table were confirmed. Those are under the general requirements of ultra precision rotary tables for freeform generating machined tools.

• 한국기계가공학회지
• /
• 제13권6호
• /
• pp.30-36
• /
• 2014

Many different cells types have been found to be highly sensitive to mechanical force imposed by their surroundings. The cellular response to external mechanical forces has very important effects on numerous biological phenomena. In spite of its importance in biological processes, the cell adhesion force remains difficult to measure quantitatively at the cellular level. In this paper, to enhance quantitative measurements of cell adhesive interactions, a new attaching system and a method in which a glass bead can be attached to an AFM cantilever was designed and fabricated, and the degree of range displacement was controlled in the system. In an experiment, the movement of the stage in the attaching system and the attaching process were measured. The effectiveness of this system was confirmed as well in the experiment. In addition, through a commercial AFM system, the spring constant of the modified AFM probe could be measured.

• Journal of Welding and Joining
• /
• 제7권4호
• /
• pp.38-45
• /
• 1989

In this study, in order to evaluate the shape and the size of the plastic zone at the notch tip before stable crack growth, a newly developed technique for plastic strain measurement, that is, the recrystallization-etching technique was applied to observe the intense strain zone at the notch tip of weld HAZ. 1) The recrystallized specimens showed that the amount of the intense strain zone, more than 20% plastic zone, was quantitatively observed as the plane strain state during the growth of the plastic zone. 2) The behavior of plastic deformation at midsection are different for parent and weld HAZ. In addition, the micro crack initiation occurs at midsection, parent and weld HAZ when the crack opening displacement(COD) value is .delta.$_{t}$=0.4mm. 3) The plastic zone for parent proceeds in the forward direction at notch tip and for weld HAZ in the right and left direction at the notch tip. 4) The relation between plastic strain energy(Wp) and COD(.delta.$_{t}$) depended on yield stress, gradient and plastic strain size.ize.

• 대한원격탐사학회지
• /
• 제21권3호
• /
• pp.221-228
• /
• 2005

Baekdusan is a Cenozoic stratovolcano in which a series of micro-seismic events and gaseous emissions have been reported in 1990s. Two-pass DInSAR technique was applied to determine displacement in the volcano by using 10 ERS SAR and 41 JERS-1 SAR datasets. Most interferometric phases out of 58 JERS-1 differential interferograms showed concentric fringe patterns that correlated with elevation. From an analysis of fringe-duration relation, the fringe patterns were found to be severely distorted specifically by stratified troposphere. To estimate the tropospheric delay, we used the data in the Sobaeksan located about 20 km away from the summit of Baekdusan. The maximum and mean magnitudes of the phase delay in the Baekdusan were respectively 13.8 cm and 3.8 cm over 1200 m in altitude. After removing tropospheric effects, a mean inflation rate was estimated to be about 3 mm per year from 1992 to 1998. Although the inflation rate of the volcano is inconclusive without ground truth data, the results indicate that there exists slow upward deformation in the Baekdusan volcano.

• 한국인터넷방송통신학회논문지
• /
• 제17권3호
• /
• pp.145-152
• /
• 2017

본 논문에서는 GNSS(Global Navigation Satellite System) 기반의 건설구조물에 대한 미세한 변위를 모니터링하기 위하여 인공위성 GNSS 통신신호와 USN(Ubiquitous Sensor Network)으로 동시 측정하고 그 결과를 분석하여 새로운 정밀측위방식을 제안한 것이다. 대형 건설 구조물에 대한 안전진단과 붕괴위험으로부터 재난을 방지하기 위한 mm단위까지의 정밀측정 방법 중에서 GNSS신기술의 적용으로 그 사례와 실험을 통하여 현재 많이 사용하는 진동계를 대신할 수 있는 영구적인 GNSS 기선방식을 유도하였으며, 이를 실험으로 입증하고자 한 것이다. 그 결과 국내에서의 가상기준점(VRS)에서의 GNSS 기선방식 적용의 정밀측위와 미세변위모니터링에서의 mm급의 수평과 수직방향의 오차를 확인할 수 있었다.