• Journal of Korea Foundry Society
• /
• v.16 no.6
• /
• pp.556-564
• /
• 1996

Variation of shape and size of solid particles and solute redistribution in Mg-9wt.%Al, AI-4.5wt.% Cu, and AI-7wt.%Si alloys were investigated when they were heated to semi-solid temperatures and held without stirring. In the case of Mg-9wt.% Al and Al-4.5wt.%Cu alloys, the polygonal shaped solid particles were agglomerated with non-uniform distribution, and there were no disappearance of the solid/solid boundary until the end of melting. But in the case of an Al-7wt.%Si alloys, two or three spherical shaped particles were coalesced or separated individually, and the coalesced particles had no solid/solid interface on the contrary to the prevous case. The maximum size of solid particles during isothermal heating at high temperature was smaller than that at lower temperature, but the time required to reach the maximum size at high temperature was shorter than that at lower temperature. The concentrations of main solute atom whose distribution coefficient is lower than 1, decreased in the primary solid particles as the liquid fraction increased, and the gradient of solute concentration was steeper in Mg-9wt.%Al alloy and Al-4.5wt.%Cu alloy than that of Al-7wt.%Si alloy.

• Transactions of Materials Processing
• /
• v.26 no.5
• /
• pp.306-313
• /
• 2017

This study investigated the microstructure, tensile strength, and high cycle fatigue properties of ADC12 aluminum alloys with different $Mg+Al_2Ca$ contents manufactured using die casting process. Microstructural observation identified the presence of ${\alpha}-Al$, eutectic Si, $Al_2Cu$, and Fe-intermetallic phases. The increase of $Mg+Al_2Ca$ content resulted in finer pore size and decreased pore distribution. Room temperature tensile strength tests were conducted at strain rate of $1{\times}10^{-3}/sec$. For 0.6%Mg ADC12, measured UTS, YS, and El were 305.2MPa, 157.0MPa, and 2.7%, respectively. For 0.8%Mg ADC12, measured UTS, YS, and El were 311.2 MPa, 159.4 MPa, and 2.4%, respectively. Therefore, 0.8% ADC12 alloy had higher strength and slightly decreased elongation compared to 0.6% Mg ADC12. High cycle fatigue tests revealed that 0.6% Mg ADC12 alloy had a fatigue limit of 150 MPa while 0.8% Mg ADC12 had a fatigue limit of 160MPa. It was confirmed that $Mg+Al_2Ca$ added ADC12 alloy achieved finer, spherical eutectic Si particles, and $Al_2Cu$ phases with greater mechanical and fatigue properties since size and distribution of pores and shrinkage cavities decreased as $Mg+Al_2Ca$ content increased.

• Applied Microscopy
• /
• v.35 no.4
• /
• pp.1-9
• /
• 2005

In this paper it is reported that a comprehensive study of the crystal structure of the fine size S-phase ($Al_2CuMg$) precipitate in Al-Cu-Mg alloy by electron diffraction experiments. The experiments involve taking the selected area diffraction pattern for a S-phase particle, simulations of the pattern based on the kinematical diffraction theory and quantitative data collection from the zone axis diffraction patterns for the comparison with calculated diffraction intensity using both the kinematical and the dynamical diffraction theory. As a result, a good fitting model of the S-phase structure turns out to be the model reported early by X-ray methods (Perlitz & Westgren, 1943), not the new model determined by HRTEM methods (Radmilovic et al., 1999).

• Journal of Surface Science and Engineering
• /
• v.22 no.4
• /
• pp.179-184
• /
• 1989

This study seeks to the morphological changes in the oxide skin of the Al-10wt.%si alloy melts. These changes depend on the oxidation time and the temperature of the molten alloy, as well as the effects of adding Mg, Cu and Ni. Thess affects observed by X-ray diffractometer(XRD) and scanning electron microscope(SEM)' Very litte oxide skins on Al-10wtwt.%Si alloy melts can be detected by XRD because it is less than the measuring capabillity of the XRD, or the formation of noncrystalline oxide skins oxide skins canbe deteced by SEM. The addition of 1%Mg and 1%Cu-1%Mg-2.5%Ni to this base alloy crystallized the structure of the oxide skins and increased the oxidation in proportion to the length of time, but adding 3% had hardiy anyaffect at all on the crystal structure of the oxide skins.

• Journal of Powder Materials
• /
• v.4 no.2
• /
• pp.100-105
• /
• 1997

In this study the changes of the hardness and microstructures during aging at 120$^{\cire}C$ of an RS-P/M Al-5.6wt%Zn-2.0wt%Mg-1.3wt%Zr-1.0wt%Mn-0.25wt%Cu alloy were studied using a transmission electron microscopy. The hardness increased rapidly at early stage of aging and reached the maximun when the specimen was aged for 24 hr. The many irregular-shaped $Al_4Mn$ and rod-shaped $Al_6Mn$ dispersoids with 0.1-0.4 $\mu$m in length were observed in the as-extruded alloy. The dark particles with 2-3 nm in size were observed in aged specimen for 5hr and those are thought to be G.P.zones or precursor of $\eta'$ precipitates. In aged specimen for 24 hr, the $\eta'$ phases were distributed homogeneously within the matrix and the PFZ with 30-40 nm in width was observed along the grain boundary. With further aging, the width of PFZ increased and $\eta$ phases were also detected within the matrix.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2002.05a
• /
• pp.86-86
• /
• 2002

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2002.05a
• /
• pp.85-85
• /
• 2002

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.44.1-44.1
• /
• 2009

본 연구에서는 Sn과 Mg를 Cu-Fe-P 합금계에 첨가 하였을 때 합금의 미세조직과 물리적 특성에 미치는 영향을 조사하였다. Cu-Fe-P 합금에 Sn과 Mg를첨가 함으로써 생성된 석출상과 합금의 미세조직, 기계적 성질 및 전기전도도를 조사하였다. 합금성분은 OES로 분석하였으며 SEM 및 EDX로 미세 석출상이생성됨을 확인하였다. 본연구를 통하여 Cu-Fe-P 합금계에 Sn과 Mg를 적절히 첨가 함으로써 고강도-고전도도의 동합금 제조가 가능함을 확인하였다.

• Korean Journal of Materials Research
• /
• v.20 no.2
• /
• pp.65-71
• /
• 2010

In this study, the effect of Sn and Mg on microstructure and mechanical properties of Cu-Fe-P alloy were investigated by using scanning electron microscope, transmission electron microscope, tensile strength, electrical conductivity, thermal softening, size and distribution of the precipitation phases in order to satisfy characteristic for lead frame material. It was observed that Cu-0.14wt%Fe-0.03wt%P-0.05wt%Si-0.1wt%Zn with Sn and Mg indicates increasing tensile strength compare with PMC90 since Sn restrained the growth of the Fe-P precipitation phase on the matrix. However, the electrical conductivity was decreased by adding addition of Sn and Mg because Sn was dispersed on the matrix and restrained the growth of the Fe-P precipitation. The size of 100 nm $Mg_3P_2$ precipitation phase was observed having lattice parameter $a:12.01{\AA}$ such that [111] zone axis. According to the results of the study, the tensile strength and the electrical conductivity satisfied the requirements of lead frame; so, there is the possibility of application as a substitution material for lead frame of Cu alloy.

• Journal of Korea Foundry Society
• /
• v.28 no.2
• /
• pp.64-68
• /
• 2008

The microstructure of Cu-Mg-P base alloys were significantly affected by small amounts of Fe and Co additions, however the tensile properties and electrical conductivity of the Cu alloys were mainly determined by the fabrication process. Relatively high electrical conductivity (> 80% IACS) was obtained in the all Cu-Mg-P based alloys when they were finally aged at $480^{\circ}C$. Tensile properties could be significantly enhanced by final cold rolling, especially at extremely low temperatures. Softening of cold-rolled alloys took place at about $450^{\circ}C$ owing to recovery and recrystallization, but it was delayed up to $500^{\circ}C$ in the Fe-added alloy.