• 한국응용과학기술학회지
• /
• 제20권3호
• /
• pp.230-236
• /
• 2003

Synthesis gas is commercially produced by a steam reforming process. However, the process is highly endothermic and energy-consuming. Thus, this study was conducted to produce synthesis gas by the partial oxidation of methane to decrease the energy cost. Supported Ni catalysts were prepared by the impregnation method. To examine the activity of the catalysts, a differential fixed bed reactor was used, and the reaction was carried out at $750{\sim}850^{\circ}C$ and 1 atm. The fresh and used catalysts were characterized by XRD, XPS, TGA and AAS. The highest catalytic activity was obtained with the 13wt% Ni/MgO catalyst, with which methane conversion was 81%, and $H_2$ and CO selectivities were 94% and 93%, respectively. 13wt% Ni/MgO catalyst showed the best $MgNiO_2$ solid solution state, which can explain the highest catalytic activity of the 13wt% Ni/MgO catalyst.

• 한국수소및신에너지학회논문집
• /
• 제22권4호
• /
• pp.443-450
• /
• 2011

The three-reactor chemical-looping process (TRCL) for the production of hydrogen from natural gas is attractive for both $CO_2$ capture and hydrogen production. In this study, redox property of $Fe_2O_3$ and $WO_3$ supported with $ZrO_2$ and $MgAl_2O_4$ were studied with temperature programmed oxidation/reduction (TPO/R) experiment. All metal oxides were prepared by ball mill method. Metal oxides supported with $ZrO_2$ showed the good redox property in TPO and TPR tests. Reduction behavior was matched well the theoretical reduction mechanism. Metal oxides supported with $MgAl_2O_4$ formed a solid solution ($MgFe_{0.6}Al_{1.4}O_4$, $MgWO_4$). $Fe_2O_3$ showed more narrow reaction range and lower reaction temperature than $WO_3$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.450.2-450.2
• /
• 2014

열전재료는 열-전기가 상호 가역적으로 변하는 재료로서, 최근 에너지 변환소재 분야에서 각광받고 있다. 열전재료의 특성 효율은 무차원 열전 성능지수(dimensionless figure of merit, $ZT={\alpha}2{\sigma}T/{\kappa}$)로 나타낼 수 있다. 여기서 ${\alpha}$는 제벡계수(Seebeck coefficient), ${\sigma}$는 전기전도도(electrical conductivity), ${\kappa}$는 열전도도(thermal conductivity), T는 Kelvin 온도를 나타낸다. 500 K에서 800 K까지의 중온 영역에서 우수한 열전특성을 보이는 $Mg_2X$ (X=Si, Ge, Sn)와 이들의 고용체는 성분원소가 독성이 없고, 매장량이 많아 친환경 열전 재료로 각광받고 있다. $Mg_2X$ 고용체 중 $Mg_2Si_{1-x}Ge_x$는 기존 $Mn_2Si$, $Mg_2Ge$, $Mg_2Sn$계 보다 더 우수한 열전 성능지수를 보인다. 다양한 제조 방법들이 시도되고 있으나, 조성설계 및 구조, 성능 조절의 어려움이 있고, Mg의 산화와 휘발 및 Mg, Si, Ge의 융점 차이가 크고 중력 편석과 반응하지 않은 원소들로 인해 제조가 상당히 어렵다. Sb가 도핑된 $Mg_2Si_{0.5}Ge_{0.5}Sb_y$ (y=0, 0.005, 0.01, 0.02, 0.03) 고용체를 고상반응으로 합성하고 진공열간 압축성형을 통해 성공적으로 제조하였다. 고용 상을 확인하기 위하여 X선 회절분석을 실시하였고, 고용체 형성과 도핑에 따른 전기적 특성변화를 평가하기 위해 Hall 효과를 측정하여 전자 이동특성을 분석하였고, 323~823 K까지 전기전도도, 제벡계수, 열전도도의 측정을 통해 열전 성능지수를 평가하였다.

• 마이크로전자및패키징학회지
• /
• 제6권2호
• /
• pp.75-81
• /
• 1999

$CaTiO_3$의 유전적 특성의 문제점을 해결하기 위해 $CaTiO_3$에 복합페로브스카이트 구조를 갖는$ La(Mg_{2/3}Ta_{1/3})O_3$를 고용시켜 마이크로파 유전특성을 조사하였다. XRD분석을 통하여 $CaTiO_3$에 $ La(Mg_{2/3}Ta_{1/3})O_3$를 첨가하면 고용체가 형성되며, 구조적으로는 Orthorhombic구조에서 $ La(Mg_{2/3}Ta_{1/3})O_3$의 첨가량이 증가함에 따라 단사정 대칭의 고용체형으로 바뀌어 가는 것을 확인할 수 있었다. (1-x)$CaTiO_3+xLa(Mg_{2/3}Ta_{1/3})O_3$에서 x값이 0.3일 때 유전율 49, 온도계수+$14ppm/^{\circ}C$, $Q \times f_0$ 값은 17000인 재료를 제조할 수 있었다.

• Bulletin of the Korean Chemical Society
• /
• 제28권2호
• /
• pp.276-280
• /
• 2007

In this work, caffeine and some catechin compounds + C, EC, EGC, and EGCG were extracted from green tea by using molecular imprinted polymers (MIP) as sorbent materials in a solid-phase extraction (SPE) process known as MISPE (molecular imprinted solid-phase extraction). For synthesis of MIP, caffeine was employed as the template, MAA as the monomer, EGDMA as the crosslinker, and AIBN as the initiator. A solution of caffeine (0.2 mg/mL in methanol) was utilized in the solid extraction cartridges following loading, washing, and elution procedures with acetonitrile, methanol, and methanol-acetic acid (90/10, %v/v) as the solvents, respectively. This solid-phase extraction protocol was applied for the extraction of caffeine and some catechin compounds from green tea. A comparison was made between the results obtained with the MIP cartridges and a traditional C18 reversed-phase cartridge. It was thereupon found that the recovery of caffeine by the MIPbased sorbent used in this work was almost two and four times greater than that by a commercially available C18 material. A quantitative analysis was conducted by high performance liquid chromatography (HPLC) using a C18 column (5 μm, 250 × 4.6 mm) with methanol/water (40/60, %v/v) as the mobile phase at a flow rate of 0.5 mL/min.

• 한국환경과학회지
• /
• 제8권2호
• /
• pp.249-254
• /
• 1999

The biosorption and desorption of Cd were carried out using brown marine algae, known as the good biosorbent of heavy metals. The content of alginate bound to light metals could be changed by the physical and the chemical pretreatment of Sargassum fluitans biomass. The Cd uptake was independent of the alginate content. In case of protonated biomass, Cd uptake was the lowest because the alginic acid of biomass was dissolved to cadmium solution during the biosorption. The maximum Cd uptake of Sargassum biomass was ranged from 79 mg/g to 139 mg/g. In case of raw biomass, the higher the alginate content of biomass, the higher was the Cd uptake. 100% of Cd and light metals sorbed in the biomass were eluted at 0.1N HCI(pH 1.1). However, the elution efficiency in $CaCl_2$ and $Ca{(NO_3)}_2$solution was varied by the concentration, the solid to liquid ratio and the pH of calcium solution. The distribution coefficient between Cd and protons in the desorption solution at pH ranged from 1.6 to 2.9 was observed on the constant stoichometric coefficient(1.3).

• 한국결정성장학회지
• /
• 제2권1호
• /
• pp.51-59
• /
• 1992

일차입경이 동일한 $Nb_20_5$분체의 응집 상태가 $Pb(Mg_{1/3}Nb_{2/3})O_3$의 생성 반응 및 소결에 미치는 영향을 조사하였다. 합성 방법으로는 고체 반응법과 용융염법으로 나누어 각각 실험하였다. 고체 반응법의 경우에는 perovskite 상의 생성 반응이 $Nb_20_5$의 응집도가 낮을수록 크게 영향을 받았으나, 용융법시에는 거의 영향을 받지 않았다. 그 이유는 고상 반응법시에는 perovskite 상의 생성이 중간생성물인 perovskite 상의 분포의 균일성, 즉 $Nb_20_5$의 응집도에 지배를 받게되나, 용해, 석출 과정에 의해 진행되는 용융염법에서는 반응물의 비표면적에 의존하므로, 응집도에는 그다지 영향을 받지않는 것으로 사료된다.

• 한국재료학회지
• /
• 제7권2호
• /
• pp.129-135
• /
• 1997

용탕단조법에 의해 제조된 Mg-6AI-xZn(x=0,1,2)합금의 기계적 성질에 미치는 시효열처리의 영향을 조사하였다. 주조상태에서의 미세조직은 초정 Mg고용체, 과포화된 상태의 Mg상, 응고과정에서 형성된 $\beta(Mg_{17}AI_{12}$)화합물 등 3개의 상으로 구성되어 있었다. 용체화처리 수 $200^{\circ}C$및 $240^{\circ}C$에서 시효열처리한 결과 Mg-6AI-xZn(x=0,1,2)합금은 $\beta$ 석출물에 의한 피크 경도값이 나타났으며, 석출물의 형태는 $200^{\circ}C$에서는 lamella 형태의 불연속 석출물이, $240^{\circ}C$에서는 미세분산분포된 연속석출물의 형태를 보였다. 용탕단조방법에 의해 제조된Mg-6AI-xZn합금의 기계적 성질은 사형주조법에 비해 인장강도 및 연신율에서 우수한 특성을 보였으며 Zn의 첨가량이 증가함에 따라 Zn의 고용강화 효과에 따라 강도값이 증가되었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제7권1호
• /
• pp.1-4
• /
• 2005

Nano- sized spherical $MgB_2$ Powders were synthesized by spray Pyrolysis method. The Influence of solution concentration and furnace reaction temperature on morphology and average particle size were investigated. For adequate preparation conditions, it has mostly spherical, solid and narrow particle size distribution. Average particle size$(X_{50})$ distribution was below 100 nm. The critical temperature for the synthesized $MgB_2$ was around 36K.

• 동력기계공학회지
• /
• 제12권1호
• /
• pp.66-71
• /
• 2008

Alumium alloys hot forging process are gaining increased acceptance in the automotive and electronic industries and hot forging is one of the most efficient manufacturing method for mass product parts. It has been investigated the microstructures and mechanical properties of Al-11.7Si-0.5Mg (KNT40-T6)alloy fabricated by hot forging process for development of connecting rod in this study. The microstructure of hot forged specimen was composed of eutectic structure of alumimum solid solution and $Mg_2Si$ precipitates. The tensile strength of solutionized Al-11.7Si-0.5Mg alloy was 217MPa. This alloy showed a good corrosion resistance using electrochemical polarization test.