• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.953-956
• /
• 1997

Micro drilling characteristics by EDM method was investigated. In detail, Micro tool electrode for EDM drilling was machined by use of WEDG method and micro hole was drilled using the machined tool electrode in SUS plate. The machining accuracy and time was compared in a different dielectric fluid. As a result, it was convinced that this method could be utilized as a fabrication technology of micro mold or micro 3 dimensional parts.

• 한국국방경영분석학회지
• /
• 제27권1호
• /
• pp.101-113
• /
• 2001

Taguchi and VTA(variation Transmission Analysis) methods have been widely used recently as new methods for product design. In this study, Taguchi method using analysis of variance and VTA method using regression analysis are reviewed and compared with each other in terms of parameter design and tolerance design. In analysis of variance, variation of quality characteristics arises from noise factors, therefore the optimal levels of design factors are selected to minimize the effect of noise factors. n regression analysis, variation of quality characteristics arises from variation of each own design factors. As a method to reduce variation of these quality characteristics, sensitivity analysis was performed for each design factors. An example of calculating tolerance interval for the given defect rate in PPM is also introduced. Especially, the new method is suggested to increase the estimation accuracy of variation of quality characteristics through regression analysis.

• 전기학회논문지P
• /
• 제60권4호
• /
• pp.220-226
• /
• 2011

This paper proposes a straightforward method of analyzing the operation characteristics for the capacitor run single-phase induction motor from the traditional equivalent circuit based on the revolving field theory. The proposed method consists of five procedures as follows: mechanical loss segregation, iron loss segregation and calculation of the equivalent circuit parameters, recalculation of parameters of the main winding side, calculation of the auxiliary winding magnetizing reactance and effective turn ratio, and analyzing the operation characteristics for this motor. When the characteristics are analyzed, the segregated mechanical and iron losses are considered as a loss resistance across input terminals of the equivalent circuit for the analysis. The validity of the proposed method is verified from the comparison between the computed results and the experimental ones for the operation characteristics.

• Journal of Advanced Marine Engineering and Technology
• /
• 제14권3호
• /
• pp.34-41
• /
• 1990

Mode Synthesis Method is applied to analyize the vibration characteristics of the press machine sold at present. Vibration analysis of the machine has not been done thoroughly as far, because of its complicated structure and much bigger unlinearity of its vibration characteristics. The press was disassembled by parts, and it was experimented by the exciting techniques and curve fitting methods, and analyzed by the Mode Synthesis Method. The 2 results were showed good agreements at each part. We confirming it, the machine was assembled, and experimented and analyzed by the same method. Also good agreements between 2 methods were obtained. In addition, impact responses of the actual moving press were agreed with the analyzed values by the Mode Synthesis Method. And we found that the first bending mode of the slide was ruling the vibration characteristics of the press.

• 전기의세계
• /
• 제22권1호
• /
• pp.42-51
• /
• 1973

The contriving equivalent circuit of single phase induction motor which does not separate the primary leakage reactance and the secondary leakage reactance by the revolving field theory, and the graphically calculating method of the characteristics with T-type circle diagram of three phase induction motor which does not suppose the primary leakage reactance can be drawn up only by the no load test, the lock test, and measuring the resistance of stator winding are suggested in this paper. The method which can calculate the parameters of the equivalent circuit and the characteristics with no load test, lock test and measuring resistance of stator windings is suggested in this paper. Considered the exciting current in lock test, we could calculate very accurate characteristics of the single phase induction motor.

• 한국전기전자재료학회논문지
• /
• 제36권1호
• /
• pp.56-61
• /
• 2023

The characteristics of write discharge were investigated when the conventional driving method with the unipolar sustain voltages, and the single sustain driving method applying the bipolar sustain voltage were applied in an AC plasma display. In the case of having a single sustain waveform, the strength of the write discharge is weakened compared to the conventional driving method during the address period, because the wall charge inside the panel is more dissipated by the lower scanning voltage. In the driving method with a single sustain waveform, the bias voltage of the other electrodes was changed to improve the write discharge characteristics. As a result, the intensity of the discharge was enhanced by 32% and the delay time was shortened by 60 ㎲.

• 한국전산유체공학회지
• /
• 제8권4호
• /
• pp.26-33
• /
• 2003

Smart UAV Development Program, one of the 21c Frontier R&D Program sponsored by MOST(Ministry of Science and Technology), was launched in 2002 As an air vehicle for the Smart UAV, CRW(Canard Rotor/wing) concept was one of the candidates compared in trade-off study. The CRW concept has not only been proven completely but its aerodynamic characteristics not known in detail yet. Two calculation methods were adopted in this study to obtain aerodynamic data for the CRW First method was the superpose DATCOM method which is capable of three lifting sufaces, and second one is the full Navier-Stokes computation around CRW configuration using overset grid method. Basic aerodynamic characteristics of the CRW configuration was analyzed and the minimum drag level with lift to drag ratio is presented. The peculiar flow characteristics around rotor/wing and hub were also examined and considered in the configuration design.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.154-160
• /
• 1998

This study describes a theoretical and experimental investigation of gas wave propagation in the pipe system. Most calculations of compressible flows in the pipe have been based on the method of characteristics. This technique has propensity to truncate waves and is difficult to apply to non-perfect gas. A method that describes the application of a two-step Lax-Wendroff acheme to solution of the unsteady one-dimentional flow in the pipe was developed. Theoretical calculations using both the method of characteristics and the two-step Lax-Wendroff method are presented including a realistic model for heat transfer and friction processes. In the present work, account is taken of the nonlinear behavior. For sections of parallel pipe, an one dimensional unsteady homentropic analysis is employed, and a numerical solution is obtained with the aid of a digital computer, using the method of characteristics and two-step Lax-Wendroff method. This analysis is then combined with boundary models, based on a quasi-steady flow approach, to give a complete treatment of the flow behavior in the pipe system.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 1994년도 추계학술발표회
• /
• pp.79-90
• /
• 1994

The goal of this research is to get a measuring system for absorption characteristics of electromagnetic wave absorbers in ferrite type which are lat grid-type special type etc. It is however very difficult to measure the absorption characteristics as in low frequency as in 30 MHz, To solve the problem therefore we propose a standing wave method and a measurement method in time domain using parallel striplines construct the measuring system and measure the characteristics of ferrite microwave absorbers in grid type using the proposed measuring system.

• 품질경영학회지
• /
• 제31권4호
• /
• pp.150-163
• /
• 2003

The purpose of this paper is to propose an interactive method using the concept of Signal­to­Noise (SN) ratios and cutting ranges for selecting the most preferred alternatives of Multiple­attribute Decision­Making(MADM) with the­smaller­the­better or the­larger­the­better characteristics. In this method the decision makers could make a grouping of attributes by their priorities. This research is based on the assumption of an equality between the attributes of MADM with the characteristics of Taguchi method. As a result, this interactive method could transform the characteristic value of Taguchi method into the size of SN ratios which are relatively easy to understand by decision makers.