• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.9
• /
• pp.754-760
• /
• 2008

A two-photon induced photoreduction process suggests a possibility for fabricating complicated metallic microstructures which can be applied to 3-D micro-circuits and optical devices, etc. The process employs the photoreduction of silver ions in a metallic solution which is composed of metallic salt ($AgNO_3$) and watersoluble polymer ((poly(4-styrenesulfonique acid) 18wt. % in $H_2O$, $(C_8H_8O_3S)_n$)). In this process, the improvement of the resolution and the uniformity of fabricated metallic structures are important issues. To address these problems, continuous forming window (CFW) is obtained from a parametric study on the conditions of laser power and scanning velocity and the direct seed generation (DSG) method is proposed. Silver nano particles are uniformly generated in a metallic solution through the DSG method, which enables the decrease of a laser power to trigger the photoreduction of silver ions as well as the increase of metal contents in a metallic solution. So the two-photon induced photoreduction property of a metallic solution is improved. Through this work, precise silver patterns are fabricated with a minimum line width of 400 nm.

• Journal of Environmental Science International
• /
• v.21 no.8
• /
• pp.901-907
• /
• 2012

The objective of this study was to evaluate bacteria removal ability of the metallic silver which was baked silver ion impregnated ceramic filter at heating condition. Silver leaking from baked ceramic filter was tested to sustain bacteria removal for a long time. Silver impregnated ceramic filter could remove E. coli completely at $10^{12}$ MPN/100ml to $10^{13}$ MPN/100ml of influent. However, ceramic filter without silver did not remove E. coli completely under the same condition. After baking, the silver impregnated ceramic filter almost didn't leak out the silver ion from filter. Photo of TEM (Transmission Electron Microscopy) showed that absorbed silver ions remained in ceramic filter after baking process and most of silver were less than 10 nm. According to the increase in the amount of silver in the ceramic filter, removal efficiencies of E. coli were increased but turbidity removal was decreased. It can be accounted that increased removal efficiency of E. coli was from disinfection of silver that is in the ceramic filter. Simulated concentrations of bacteria agree well with the observed experimental effluent concentration data. Moreover, first-order decay coefficients increased to 0.0034/min after silver was added in the ceramic filter. Increase of first-order decay coefficient proves that silver-added ceramic filter can remove bacteria easily.

• Nuclear Engineering and Technology
• /
• v.32 no.6
• /
• pp.531-536
• /
• 2000

The extraction of precious metals from aqueous solutions is performed by using a photoredox reaction with a Q-switched Nd:YAG laser. The metallic silver was efficiently precipitated and extracted from the silver nitrate solution by laser photolysis. An optimum reaction condition for silver extraction was determined by adjusting various experimental factors such as type of reducing agent, type of acids and reaction time. The composition of the reaction product was analyzed and it was identified as metallic silver, not other molecular types. The photoreaction of chromium(III) chloride in an acidic aqueous solution was also investigated. The 355 nm laser light was better suited for the reaction of silver nitrate as well as chromium(III) chloride in an acidic solution compared to the 532 nm light.

• Journal of Sensor Science and Technology
• /
• v.32 no.4
• /
• pp.252-256
• /
• 2023

A one-step method for nanoscale patterning of silver ionic ink on a substrate is developed using a microscale, elastic mold deformation. This method yields unique micro/nanoscale metallic structures that differ from those produced using the original molds. The linewidth of these metallic structures is significantly reduced (approximately 10 times) through the sidewall deformation of the original mold cavity on a thin liquid film, as verified by finite element analysis. The process facilitates the fabrication of various, isolated and complex micro/nanoscale metallic structures with negligible residual layers at low cost and high throughput. These structures can be utilized for various applications, including optoelectronics, wearable sensors, and metaverse-related devices. Our approach offers a promising tool for manipulation and fabrication of micro/nanoscale structures of various functional materials.

• Journal of Sensor Science and Technology
• /
• v.25 no.2
• /
• pp.143-147
• /
• 2016

Characteristics of the conventional gold (Au) surface plasmon resonance (SPR) chip, bi-metallic(Au/silver (Ag)) SPR chip, and tri-metallic(Au/Ag/Au) SPR chip were investigated and compared in the intensity measurement mode for the enhancement of SPR image sensor reactivity. Reflectance curves of the Au, bi- and tri-metallic SPR chips were acquired in phosphate-buffered saline (PBS) solution and were compared. The line width of the reflectance curve of the bi-metallic chip was the narrowest among the three different types of the chips. Also, the tangential slope of the bi-metallic chip was steeper than those of the other chips. Various concentrations of bovine serum albumin (BSA) were utilized in the SPR experiment. As a result, among the above three chips reflectance variation value of the bi-metallic chip was the largest.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.1832-1836
• /
• 2014

A deep understanding of the metallic silver catalysts formation process on oxide support and the formation mechanism is of great scientific and practical meaning for exploring better catalyst preparing procedures. Herein the thermal decomposition process of supported silver catalyst with silver oxalate as the silver precursor in the presence of ethylenediamine and ethanolamine is carefully investigated by employing a variety of characterization techniques including thermal analysis, in situ diffuse reflectance infrared Fourier transform spectroscopy, scanning electron microscopy, and X-ray diffraction. The formation mechanism of supported silver particles was revealed. Results showed that formation of metallic silver begins at about $100^{\circ}C$ and activation process is essentially complete below $145^{\circ}C$. Formation of silver was accompanied by decomposition of oxalate group and removal of organic amines. Catalytic performance tests using the epoxidation of ethylene as a probe reaction showed that rapid activation (for 5 minutes) at a relatively low temperature ($170^{\circ}C$) afforded materials with optimum catalytic performance, since higher activation temperatures and/or longer activation times resulted in sintering of the silver particles.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.8
• /
• pp.1189-1194
• /
• 2004

The adsorption isotherms of N2 onto the metallic silver treated activated carbon fiber samples after acid treatment are Type I with a small amount of capillary condensation hysteresis. Increasing amount of acid treatment leads to a decrease in SBETs and external surface area. But, micropore volume and average pore diameter are presented in constant regular values with increasing amount of sulfuric acid treatment. SEM observes the surface morphology and crystal grown state of metal on the fiber surface. The results of EDX of Ag-activated carbon fiber pre-treated with acid show the spectra corresponding to almost all samples rich in silver with increasing the amount of acid treated. The FT-IR spectra of Ag-activated carbon fiber show that the acid pre-treatment is consequently associated with the homogeneous dispersion of metal with the increased surface acidity of the activated carbon fiber. The type and quality of oxygen groups are determined with Boehm titration method. From the those results, a positive influence of the acidic groups on the carbon fiber surface by acid treatment is also demonstrated by an increase in the contents of metallic silver with increasing of acidic groups.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.25 no.4 s.34
• /
• pp.7-16
• /
• 1999

Silver-containing antimicrobial inorganic pigments that have been developed so far still have problems, which result from silver's unique metallic color and discoloration. Therefore, those things are used only for make-up cosmetics or just the restricted amount is used. Although the use of white-base pigments or iron oxides has been considered to solve those problems, they virtually fail to serve as a perfect substitute. So it seems difficult to use enough quantity of those materials or to apply them to diverse kinds of products. The purpose of this study was, accordingly, to attain the complete removal of metallic color and the maintenance of color. Additionally, a rosemary extract was employed to develop a silver-containing inorganic antimicrobial pigment(Ag-AIP-R) that has an improved antimicrobial effect and anti oxidative effect.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1510-1515
• /
• 2004

The effects of additive ions on the generation of metallic nanoparticles were evaluated using a corona induced supersonic nozzle. Applying the corona discharge to the nanoparticle generator, a tungsten needle and the supersonic nozzle are used as an anode electrode and a cathode electrode respectively. The corona ions act as nuclei for the silver vapor condensation. The ion density was controlled precisely as varying the applied voltage between electrode and nozzle. The mean diameter of the silver particle decreases as the ion density increases. However, the number concentration of the silver particle tended to increase with the ion density. The size distribution is more uniform as the ion density increases.

• Proceedings of the SCSK Conference
• /
• 1999.10a
• /
• pp.7-16
• /
• 1999

Silver-containing antimicrobial inorganic pigments that have been developed so far still have problems, which result from silver’s unique metallic color and discoloration. Therefore, those things are used only far make-up cosmetics or just the restricted amount is used. Although the use of white-base pigments or iron oxides has been considered to solve those problems, they virtually fail to serve as a perfect substitute. So it seems difficult to use enough quantity of those materials or to apply them to diverse kinds of products. The purpose of this study was, accordingly, to attain the complete removal of metallic color and the maintenance of color. Additionally, a rosemary extract was employed to develop a silver-containing inorganic antimicrobial pigment(Ag-AIP-R) that has an improved antimicrobial effect and antioxidative effect.