• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.206.2-206.2
• /
• 2015

최근 비정질 산화물 반도체 thin film transistor(TFT)는 차세대 투명 디스플레이로 많은 관심을 받고 있으며 활발한 연구가 진행되고 있다. 산화물 반도체 TFT는 기존의 비정질 실리콘 반도체에 비하여 큰 on/off 전류비, 높은 이동도 그리고 낮은 구동전압으로 인하여 차세대 투명 디스플레이 산업에 적용 가능하다는 장점이 있다. 한편 기존의 sputter나 evaporator를 이용한 증착 방식은 우수한 막의 특성에도 불구하고 많은 시간과 제작비용이 든다는 단점을 가지고 있다. 따라서 본 연구에서는 별도의 고진공 시스템이 필요하지 않을 뿐만 아니라 대면적화에도 유리한 용액공정 방식을 이용하여 박막 트렌지스터를 제작하였으며 thermal 열처리와 microwave 열처리 방식에 따른 전기적 특성을 비교 및 분석하고 각 열처리 방식의 열처리 온도 및 조건을 최적화 하였다. 제작된 박막 트렌지스터는 p-type bulk silicon 위에 산화막이 100 nm 형성된 기판에 spin coater을 이용하여 Al-Zn-Sn-O 박막을 형성하였다. 연속해서 photolithography 공정과 BOE (30:1) 습식 식각 과정을 이용해 활성화 영역을 형성하여 소자를 제작하였다. 제작 된 소자는 Pseudo-MOS FET구조이며, 프로브 탐침을 증착 된 채널층 표면에 직접 접촉시켜 소스와 드레인 역할을 대체하여 동작시킬 수 있어 전기적 특성평가가 용이하다는 장점을 가지고 있다. 그 결과, microwave를 통해 열처리한 소자는 100oC 이하의 낮은 열처리 온도에도 불구하고 furnace를 이용하여 열처리한 소자와 비교하여 subthreshold swing(SS), Ion/off ratio, field-effectmobility 등이 개선되는 것을 확인하였다. 따라서, microwave 열처리 공정은 향후 저온 공정을 요구하는 MOSFET 제작 시의 훌륭한 대안으로 사용 될 것으로 기대된다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.2
• /
• pp.109-113
• /
• 2020

A power device is a component used as a switch or rectifier in power electronics to control high voltages. Consequently, power devices are used to improve the efficiency of electric-vehicle (EV) chargers, new energy generators, welders, and switched-mode power supplies (SMPS). Power device designs, which require high voltage, high efficiency, and high reliability, are typically based on MOSFET (metal-oxide-semiconductor field-effect transistor) and IGBT (insulated-gate bipolar transistor) structures. As a unipolar device, a MOSFET has the advantage of relatively fast switching and low tail current at turn-off compared to IGBT-based devices, which are built on bipolar structures. A superjunction structure adds a p-base region to allow a higher yield voltage due to lower R_DS (on) and field dispersion than previous p-base components, significantly reducing the total gate charge. To verify the basic characteristics of the superjunction, we worked with a planar type MOSFET and Synopsys' process simulation T-CAD tool. A basic structure of the superjunction MOSFET was produced and its changing electrical characteristics, tested under a number of environmental variables, were analyzed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.152-153
• /
• 2012

Ion sensitive field effect transistor (ISFET)는 전해질 속 각종 이온농도를 측정하는 반도체 이온 센서이다. 이 소자의 기본 구조는 metal oxide semiconductor field effect transistor (MOSFET)에서 고안되었으며 게이트 컨택 부분이 기준전극과 전해질로 대체되어진 구조를 가지고 있다 [1]. ISFET는 기존의 반도체 CMOS 공정과 호환이 가능하고 제작이 용이할 뿐만 아니라, pH용액에 대한 빠른 반응 속도, 비표지 방식의 생체물질 감지능력, 낮은 단가 및 소자의 집적이 용이하다는 장점을 가지고 있다. ISFET pH센서의 감지특성에 결정하는 요소 중 가장 중요한 것은 소자의 감지막이라고 할 수 있다. 감지막은 감지 대상 물질과 물리적으로 직접 접촉되는 부분으로서 일반적으로 기계적/화학적 강도가 우수한 실리콘 산화막(SiO2)이 많이 사용되어져 왔다. 최근에는 기존의 SiO2 보다 성능이 향상된 감지막을 개발하기 위하여 Al2O3, HfO2, ZrO2, 그리고 Ta2O5와 같은 고유전 상수(high-k)를 가지는 물질들을 EIS 센서의 감지막으로 이용하는 연구가 활발하게 진행되고 있다. 하지만 지속적인 high-k 물질들에 대한 연구에도 불구하고 각각의 물질이 갖는 한계점이 드러났다. 본 연구에서는 SOI기판에서 SiO2 /HfO2 (OH), SiO2/Al2O3 (OA) 이단 적층 그리고 SiO2/HfO2/Al2O3 (OHA) 삼단적층 감지막을 갖는 ISFET을 제작하고 각 감지막의 특성을 평가하였다. 평가된 특성의 결과가 아래의 표1에 요약되었다. 그 결과, 각 high-k 물질이 갖는 한계점을 극복하기 위하여 제안된 OHA감지막은 기존에 OH, OA가 갖는 장점을 취하면서 단점을 최소화 시키는 최적화된 감지막의 감지특성을 보였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.200-200
• /
• 2010

In recent times, metal oxide semiconductors thin films transistor (TFT), such as zinc and indium based oxide TFTs, have attracted considerable attention because of their several advantageous electrical and optical properties. There are many deposition methods for fabrication of ZnO-based materials such as chemical vapor deposition, RF/DC sputtering and pulsed laser deposition. However, these vacuum process require expensive equipment and result in high manufacturing costs. Also, the methods is difficult to fabricate various multicomponent oxide semiconductor. Recently, several groups report solution processed metal oxide TFTs for low cost and non vacuum process. In this study, we have newly developed solution-processed TFTs based on Ti-related multi-component transparent oxide, i. e., InTiO as the active layer. We propose new multicomponent oxide, Titanium indium oxide(TiInO), to fabricate the high performance TFT through the sol-gel method. We investigated the influence of relative compositions of Ti on the electrical properties. Indium nitrate hydrate [$In(NO^3).xH_2O$] and Titanium isobutoxide [$C_{16}H_{36}O_4Ti$] were dissolved in acetylacetone. Then monoethanolamine (MEA) and acetic acid ($CH_3COOH$) were added to the solution. The molar concentration of indium was kept as 0.1 mol concentration and the amount of Ti was varied according to weighting percent (0, 5, 10%). The complex solutions become clear and homogeneous after stirring for 24 hours. Heavily boron (p+) doped Si wafer with 100nm thermally grown $SiO_2$ serve as the gate and gate dielectric of the TFT, respectively. TiInO thin films were deposited using the sol-gel solution by the spin-coating method. After coating, the films annealed in a tube furnace at $500^{\circ}C$ for 1hour under oxygen ambient. The 5% Ti-doped InO TFT had a field-effect mobility $1.15cm^2/V{\cdot}S$, a threshold voltage of 4.73 V, an on/off current ratio grater than $10^7$, and a subthreshold slop of 0.49 V/dec. The 10% Ti-doped InO TFT had a field-effect mobility $1.03\;cm^2/V{\cdot}S$, a threshold voltage of 1.87 V, an on/off current ration grater than $10^7$, and a subthreshold slop of 0.67 V/dec.

• Journal of Sensor Science and Technology
• /
• v.30 no.4
• /
• pp.236-242
• /
• 2021

In this paper, we report the fabrication of the tip-on-gate of a field-effect-transistor (ToGoFET) probe using a standard complementary metal-oxide-semiconductor (CMOS) process and the performance evaluation of the fabricated probe. After the CMOS process, I-V characteristic measurement was performed on the reference MOSFET. We confirmed that the ToGoFET probe could be operated at a gate voltage of 0 V due to channel ion implantation. The transconductance at the operating point (Vg = 0 V, Vd = 2 V) was 360 ㎂/V. After the fabrication process was completed, calibration was performed using a pure metal sample. For sensitivity calibration, the relationship between the input voltage of the sample and the output current of the probe was determined and the result was consistent with the measurement result of the reference MOSFET. An oxide sample measurement was performed as an example of an application of the new ToGoFET probe. According to the measurement, the ToGoFET probe could spatially resolve a hundred nanometers with a height of a few nanometers in both the topographic image and the ToGoFET image.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.536-541
• /
• 2003

In order to avoid oxygen contamination on the diamond surface as far as possible during the device process, the A1/Ca $F_2$/diamond MISFET(metal-insulator-semiconductor field-effect transistor) was prepared by ultrahigh vacuum process and its electrical properties were investigated. The surface conductive layer of fluorinated diamond surface was employed for the conducting channel of the MISFET. The observed effective mobility(${\mu}$e$\_$ff/) of the MISFET was 300 c $m^2$/Vs, which is the highest value obtained until now in the diamond FET. Besides, the measured surface state density of the device was ∼10$\^$11//c $m^2$ eV, which is comparable with conventional Si MOSFET$\_$s/(metal-oxide-semiconductor field-effect-transistors). This work is the first report of the fluorinated diamond MISFET prepared by ultrahigh vacuum process and its application to inverter circuit.

• Journal of information and communication convergence engineering
• /
• v.10 no.2
• /
• pp.200-204
• /
• 2012

This study has presented the analysis of breakdown voltage for a double-gate metal-oxide semiconductor field-effect transistor (MOSFET) based on the doping distribution of the Gaussian function. The double-gate MOSFET is a next generation transistor that shrinks the short channel effects of the nano-scaled CMOSFET. The degradation of breakdown voltage is a highly important short channel effect with threshold voltage roll-off and an increase in subthreshold swings. The analytical potential distribution derived from Poisson's equation and the Fulop's avalanche breakdown condition have been used to calculate the breakdown voltage of a double-gate MOSFET for the shape of the Gaussian doping distribution. This analytical potential model is in good agreement with the numerical model. Using this model, the breakdown voltage has been analyzed for channel length and doping concentration with parameters such as projected range and standard projected deviation of Gaussian function. As a result, since the breakdown voltage is greatly changed for the shape of the Gaussian function, the channel doping distribution of a double-gate MOSFET has to be carefully designed.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.5
• /
• pp.1-7
• /
• 2002

Deep sub-micron bulk CMOS circuits require gate electrode materials such as metal silicide and titanium silicide for gate oxides. Many authors have conducted research to improve the quality of the sub-micron gate oxide. However, few have reported on the electrical quality and reliability of an ultra-thin gate. In this paper, we will recommend a novel shallow trench isolation structure and a two-step TiS $i_2$ formation process to improve the corner metal oxide semiconductor field-effect transistor (MOSFET) for sub-0.1${\mu}{\textrm}{m}$ VLSI devices. Differently from using normal LOCOS technology, deep sub-micron CMOS devices using the novel shallow trench isolation (STI) technology have unique "inverse narrow-channel effects" when the channel width of the device is scaled down. The titanium silicide process has problems because fluorine contamination caused by the gate sidewall etching inhibits the silicide reaction and accelerates agglomeration. To resolve these Problems, we developed a novel two-step deposited silicide process. The key point of this process is the deposition and subsequent removal of titanium before the titanium silicide process. It was found by using focused ion beam transmission electron microscopy that the STI structure improved the narrow channel effect and reduced the junction leakage current and threshold voltage at the edge of the channel. In terms of transistor characteristics, we also obtained a low gate voltage variation and a low trap density, saturation current, some more to be large transconductance at the channel for sub-0.1${\mu}{\textrm}{m}$ VLSI devices.

• Journal of the Korean Society for Railway
• /
• v.13 no.5
• /
• pp.504-508
• /
• 2010

The development of high voltage Insulated Gate Bipolar Transistor (IGBT) have given new device advantage in the areas where they compete with conventional GTO (Gate Turnoff Thyristor) technology. The IGBT combines the advantages of a power MOSFET (Metal-Oxide Semiconductor Field-Effect Transistor) and a bipolar power transistor. The change of electrical characteristics for IGBT is mainly coming from the change of characteristics of MOSFET at the input gate and the PNP transistors at the output. The change of threshold voltage, which is one of the important design parameters, is brought by charge trapping at the gate oxide under the environment that radiation exists. The energy loss will be also studied as the inductance values are changed. In this paper, the electrical characteristics are simulated by SPICE, and compared for variation of inductance and threshold voltage based on IGBT.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.3
• /
• pp.45-50
• /
• 2014

In this paper, we propose a super-junction MOSFET (SJ MOSFET) fabricated through a simple pillar forming process by varying the Si epilayer thickness and doping concentration of pillars using SILVACO TCAD simulation. The design of the SJ MOSFET structure is presented, and the doping concentration of pillar, breakdown voltage ($V_{BR}$) and drain current are analyzed. The device performance of conventional Si planar metal-oxide semiconductor field-effect transistor(MOSFET), Si SJ MOSFET, and SiGe SJ MOSFET was investigated. The p- and n-pillars in Si SJ MOSFET suppressed the punch-through effect caused by drain bias. This lead to the higher $V_{BR}$ and reduced on resistance of Si SJ MOSFET. An increase in the thickness of Si epilayer and decrease in the former is most effective than the latter. The implementation of SiGe epilayer to SJ MOSFET resulted in the improvement of $V_{BR}$ as well as drain current in saturation region, when compared to Si SJ MOSFET. Such a superior device performance of SiGe SJ MOSFET could be associated with smaller bandgap of SiGe which facilitated the drift of carriers through lower built-in potential barrier.