• Journal of Technologic Dentistry
• /
• v.37 no.2
• /
• pp.69-76
• /
• 2015

Purpose: In this study, the marginal fitness of ceramic Co-Cr metal crown made by precision casting, milling, and selective laser melting method were compared. Methods: The ceramic Co-Cr metal crown manufactured by precision casting used the lost wax(LC specimen) method. The abutment were scanned and then made by milling(CM specimen), selective laser melting(CS specimen) method. The specimen were cut bucco-lingual and mesio-distal, and absolute marginal discrepancy and marginal gap were measured using a digital microscope. The surface roughness of the crown was also observed. Results: On the bucco-lingual axial, absolute marginal discrepancy was the LC specimen $31.72({\pm}4.58){\mu}m$, the CM specimen $78.29({\pm}3.28){\mu}m$ and the CS specimen $143.13({\pm}3.83){\mu}m$, respectively. On the bucco-lingual axial, marginal gap was the LC specimen $22.70({\pm}1.46){\mu}m$, the CM specimen $22.70({\pm}1.49){\mu}m$ and CS specimen $99.60({\pm}1.57){\mu}m$, respectively. Conclusion: For ceramic Co-Cr metal crowns, LC specimen was superior for absolute marginal discrepancy and marginal gap. The surface of metal crowns by selective laser melting were the roughest.

• Particle and aerosol research
• /
• v.9 no.1
• /
• pp.31-36
• /
• 2013

In this study, Mo metal powder was prepared by hydrogen reduction of Mo trioxides with different purity of 2N and 3N grades. We have obtained Mo metal powder with oxygen content of 1450 ppm by hydrogen reduction and subsequent heat treatment for degassing. Using the Mo metal powder, a low-oxygen Mo ingot was prepared by repetitive vacuum arc melting. The oxygen content of the obtained Mo ingot was less than 70 ppm after vacuum arc melting for 30 min. The purity of the Mo metal powder and the ingot was evaluated using glow discharge mass spectrometry. The purity of the respective Mo ingots was increased to 3N and 4N grades from the Mo powder of 2N and 3N grades after the repetitive vacuum arc melting. The low oxygen Mo ingot thus can be used as a raw material for sputtering targets.

• Journal of Ship and Ocean Technology
• /
• v.11 no.3
• /
• pp.14-23
• /
• 2007

Welding processes cause undesirable problems, such as residual stresses and deformations due to the thermal loads imposed by local heating, melting, and cooling processes. This paper presents a computational modeling technique to simulate the Gas Metal Arc Welding (GMAW) process, emphasizing the effect of the melting bead on the residual stress distribution. Both a three-bar analogy and a three-dimensional thermo-mechanical finite element analysis are carried out in order to explain the effect. Element (de)activation, enthalpy, and adjustment of the reference temperature of thermal strain are considered with respect to the effect of the weld filler metal added to the base metal during a thermo-elastic-plastic analysis. Stress distributions obtained by the present study are compared with measured values and available data from other studies. The effect of the melting bead on the residual stress distribution is discussed and demonstrated.

• Environmental Analysis Health and Toxicology
• /
• v.16 no.2
• /
• pp.103-114
• /
• 2001

Worldwide trend of waste treatment technology is rapidly transferring from "incineration system" to "gasification & melting system" which can derive the resources from waste and charge no more environmental burden to nature. And therefore it is necessary for our country to adopt gasification & melting system urgently to present the land pollution and lack of landfill area. Among several gasification and melting processes Daewoo-Thermoselect gasification and melting system is the representative process which can transfer waste to resources such as sin-gas, molten slag, metal hydroxide, mixed salt and sulfur through the process of compaction, degasification, gasification and melting.

• Journal of Soil and Groundwater Environment
• /
• v.6 no.1
• /
• pp.23-31
• /
• 2001

Melting is one of the most effective treatments for stabilizing heavy metals and also creates high value by-products. In this study, authors evaluated the leaching characteristics of heavy metals in melting slag obtained by incinerator ashes. In order to evaluate the environmental compatibility of the recycled melting slag, the samples were analysed various leaching tests of heavy metals with raw incinerator ashes, melting slag and the construction materials recycled from melting slag. As the results : (1) The leaching concentrations of the melting slag were lower than those of the raw incinerator ashes in the experiment performed in accordance with Korea Standard Leaching Test (KSLT). (2) The heavy metal concentration of long term leaching test, which was conducted in various pH conditions, were under the standard level of regulation in KSLT. (3) The leaching concentration of mortar samples used for evaluating the feasibility of recycling the melting slag as construction materials also shows the suitable range for recycling. (4) The result of leaching test with the method of RG Min-StB 93, FGSV (Forschungsgesellschaft fur Stra$\beta$en- und Verkehrswesen) met the requirements in German.

• Journal of Korea Foundry Society
• /
• v.24 no.6
• /
• pp.314-322
• /
• 2004

The CaO crucible is expected to serve as a useful tool for melting Ti and its alloys due to its thermodynamic stability. However, tjere still remain problems that need to be resolved in the melting of Ti and its alloys to enable commerical use. The cause of the defects of Ti-6AI-4V alloy castings melted in the CaO crucible were examined and compared with induction skull melting. The key factors of the melting technique using the CaO crucible, affecting the quality of Ti-6AI-4V alloy castings, were investigated. Defects of the Ti-6AI-4V alloy castings are caused by the chemical reduction of CaO by Ti. Pressurizing with argon gas in a vacuum induction chamber is effective for reducing the defects. Preheating of the charged material in the crucible and quick pouring into a mold of lower temperature, just after melting down, are important for produsing sound Ti-6AI-4V castings.

• Korean Journal of Materials Research
• /
• v.26 no.7
• /
• pp.376-381
• /
• 2016

For the development of a low-melting point filler metal for brazing aluminum alloy, we analyzed change of melting point and wettability with addition of Sn into Al-20Cu-10Si filler metal. DSC results showed that the addition of 5 wt% Sn into the Al-20Cu-10Si filler metal caused its liquidus temperature to decrease by about 30 oC. In the wettability test, spread area of melted Al-Cu-Si-Sn alloy is increased through the addition of Sn from 1 to 5 wt%. For the measuring of the mechanical properties of the joint region, Al 3003 plate is brazed by Al-20Cu-10Si-5Sn filler metal and the mechanical property is measured by tensile test. The results showed that the tensile strength of the joint region is higher than the tensile strength of Al 3003. Thus, failure occurred in the Al 3003 plate.

• ETRI Journal
• /
• v.41 no.6
• /
• pp.820-828
• /
• 2019

A highly reliable conductive adhesive obtained by transient liquid-phase sintering (TLPS) technologies is studied for use in high-power device packaging. TLPS involves the low-temperature reaction of a low-melting metal or alloy with a high-melting metal or alloy to form a reacted metal matrix. For a TLPS material (consisting of Ag-coated Cu, a Sn96.5-Ag3.0-Cu0.5 solder, and a volatile fluxing resin) used herein, the melting temperature of the metal matrix exceeds the bonding temperature. After bonding of the TLPS material, a unique melting peak of TLPS is observed at 356 ℃, consistent with the transient behavior of Ag₃Sn + Cu₆Sn₅ → liquid + Cu₃Sn reported by the National Institute of Standards and Technology. The TLPS material shows superior thermal conductivity as compared with other commercially available Ag pastes under the same specimen preparation conditions. In conclusion, the TLPS material can be a promising candidate for a highly reliable conductive adhesive in power device packaging because remelting of the SAC305 solder, which is widely used in conventional power modules, is not observed.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.133-138
• /
• 2005

The worldwide trend of waste treatment technology is rapidly transferring from "incineration system" to "gasification & melting system" which can derive the resources from waste and charge no more environmental burden to nature. And therefore it is necessary to adopt gasification & melting system to prevent the land pollution and to solve the problem of landfill area. Among several thermal waste treatment processes gasification and melting system is the representative process which can transfer waste to resources such as syn-gas, molten slag, metal hydroxide, mixed salt and sulfur through the process of compaction, pyrolysis, gasification and melting.

• Journal of the Korean Ceramic Society
• /
• v.11 no.1
• /
• pp.3-9
• /
• 1974

The role of added metal oxide in the adherence mechanism of low melting glass to several metal plates such as oxygen free high conducting copper, low carbon steel, chrominum galvanized on copper, and stainless steel was investigated. The metal oxide which added to glass were cupric oxide, ferric oxide, chromic oxide, and stainless steel oxide. The glass to that various metla oxide were added, sealed with several metal plates in the electric furnace at $650^{\circ}C$ for 5 minutes. The results as follows; 1) The interfacial reaction was promoted and strong chemical bonding with glass and metals by which the surface energy was decreased showed excellent sealing by addition of metal oxide. 2) When the interfacial reaction of glass and metals was promoted by addition of metal oxide found out that various adhernece mechanism were related to the sealing. 3) When the amount of metal oxide addition was 3-5% the excellent sealing was achieved.