• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.56-63
• /
• 2010

This work proposes a 12b 100MS/s 0.13um CMOS pipeline ADC for battery-powered mobile video applications such as DVB-Handheld (DVB-H), DVB-Terrestrial (DVB-T), Satellite DMB (SDMB), and Terrestrial DMB (TDMB) requiring high resolution, low power, and small size at high speed. The proposed ADC employs a three-step pipeline architecture to optimize power consumption and chip area at the target resolution and sampling rate. A single shared and switched op-amp for two MDACs removes a memory effect and a switching time delay, resulting in a fast signal settling. A two-step reference selection scheme for the last-stage 6b FLASH ADC reduces power consumption and chip area by 50%. The prototype ADC in a 0.13um 1P7M CMOS technology demonstrates a measured DNL and INL within 0.40LSB and 1.79LSB, respectively. The ADC shows a maximum SNDR of 60.0dB and a maximum SFDR of 72.4dB at 100MS/s, respectively. The ADC with an active die area of 0.92 $mm^2$ consumes 24mW at 1.0V and 100MS/s. The FOM, power/($f_s{\times}2^{ENOB}$), of 0.29pJ/conv. is the lowest of ever reported 12b 100MS/s ADCs.

• The KIPS Transactions:PartA
• /
• v.12A no.6 s.96
• /
• pp.523-530
• /
• 2005

When a PCI 2.2 bus master requests data using Memory Read command, a target device may hold PCI bus without data to be transferred for long time because a target device needs time to prepare data infernally. Because the usage efficiency of the PCI bus and the data transfer efficiency are decreased due to this situation, the PCI specification recommends to use the Delayed Transaction mechanism to improve the system performance. But the mechanism cann't fully improve performance because a target device doesn't know the exact size of prefetched data. In the previous work, we propose a new method called Prefetch Request when a bus master intends to read data from the target device. In this paper, we design PCI 2.2 controller and local device that support the proposed method. The designed PCI 2.2 controller has simple local interface and it is used to convert the PCI protocol into the local protocol. So the typical users, who don't know the PCI protocol, can easily design the PCI target device using the proposed PCI controller. We propose the basic behavioral verification, hardware design verification, and random test verification to verify the designed hardware. We also build the test bench and define assembler instructions. And we propose random testing environment, which consist of reference model, random generator ,and compare engine, to efficiently verify corner case. This verification environment is excellent to find error which is not detected by general test vector. Also, the simulation under the proposed test environment shows that the proposed method has the higher data transfer efficiency than the Delayed Transaction about $9\%$.

• The KIPS Transactions:PartA
• /
• v.16A no.5
• /
• pp.357-368
• /
• 2009

Mobile IP storage has been proposed to overcome storage limitation in the flash memory and hard disks. It provides almost capacity-free space for mobile devices over wireless IP networks. However, battery lifetime of the mobile devices is reduced rapidly because of power consumption with continuous use of a WLAN device when multimedia contents are being streamed through the mobile IP storage. This paper proposes an energy-efficient WLAN device power control technique for streaming multimedia contents with the mobile IP storage. The proposed technique consists of a prefetch buffer input/output module, a WLAN device power control module, and a reconfigurable prefetch buffer module. Besides, it adaptively determines the size of the prefetch buffer according to a quality of the multimedia contents, and it dynamically controls the power mode of the WLAN device on the basis of power on-off operations while streaming the multimedia contents. We evaluate the performance of the proposed technique on a PXA270-based mobile device that employs the embedded linux 2.6.11, Intel iSCSI reference codes, and a WLAN device. Extensive experiments reveal that the proposed technique can save the energy consumption of the WLAN device up to 8.5 times with QVGA multimedia contents, as compared with no power control.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.8A
• /
• pp.739-752
• /
• 2002

Recently, to utilize the limited bandwidth effectively, the concept of partial response (PR) signaling has widely been adopted in both the high-speed data transmission and high-density digital recording/playback systems such as digital microwave, digital subscriber loops, hard disk drives, digital VCR's and digital versatile recordable disks and so on. This paper is concerned with adaptive equalization of partial response channels particularly for the magnetic recording channels. Specifically we study how the PR channel equalizers work for different choices of desired or reference signals used for adjusting the equalizer weights. In doing so, we consider three different configurations that are actually implemented in the commercial products mentioned above. First of all, we show how to compute the theoretical values of the optimum Wiener solutions derived by minimizing the mean-squared error (MSE) at the equalizer output. Noting that this equalizer MSE measure cannot be used to fairly compare the three configurations, we propose to use the data MSE that is computer just before the final detector for the underlying PR system. We also express the data MSE in terms of the channel impulse response values, source data power and additive noise power, thereby making it possible to compare the performance of the configurations under study. The results of extensive computer simulation indicate that our theoretical derivation is correct with high precision. Comparing the three configurations, it also turns out that one of the three configurations needs to be further improved in performance although it has an apparent advantage over the others in terms of memory size when implemented using RAM's for the decision feedback part.

• 한국해양학회지
• /
• v.22 no.2
• /
• pp.57-62
• /
• 1987

The Markov chain properties of the sea surface temperature (SST) anomalies, namely, the dependency of the monthly SST anomaly on that of the previous month, are studied based on the SST data for 28years(1957-1984) at 5 stations in the southeastern coast of Korea. Wi classified the monthly SST anomalies at each station into the low, the normal and the high state, and computed transition probabilities between SST anomalies of two successive months The standard deviation of SST anomalies at each station is used as a reference for the classification of SST anomalies into 3states. The transition probability of the normal state to remain in the same state is about 0.8. The transition probability of the high or the low states to remain in the same state is about one half. The SST anomalies have almost no probability to transit from the high (the low) state to the low (the high) state. Statistical tests show that the Markov chain properties of SST anomalies are stationary in tine and homogeneous in space. The multi-step Markov chain analysis shows that the 'memory' of the SST anomalies at the coastal stations remains about 3 months.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.1
• /
• pp.1-17
• /
• 2002

The purpose of this study is to examine the possibility of thermal injury to bone tissues during an implant site preparation under the same condition as a typical clinical practice of $Br{\aa}nemark$ implant system. All the burs for $Br{\aa}nemark$ implant system were studied except the round bur The experiments involved 880 drilling cases : 50 cases for each of the 5 steps of NP, 5 steps of RP, and 7 steps of WP, all including srew tap, and 30 cases of 2mm twist drill. For precision drilling, a precision handpiece restraining system was developed (Eungyong Machinery Co., Korea). The system kept the drill parallel to the drilling path and allowed horizontal adjustment of the drill with as little as $1{\mu}m$ increment. The thermocouple insertion hole. that is 0.9mm in diameter and 8mm in depth, was prepared 0.2mm away from the tapping bur the last drilling step. The temperatures due to countersink, pilot drill, and other drills were measured at the surface of the bone, at the depths of 4mm and 8mm respectively. Countersink drilling temperature was measured by attaching the tip of a thermocouple at the rim of the countersink. To assure temperature measurement at the desired depths, 'bent-thermocouples' with their tips of 4 and 8mm bent at $120^{\circ}$ were used. The profiles of temperature variation were recorded continuously at one second interval using a thermometer with memory function (Fluke Co. U.S.A.) and 0.7mm thermocouples (Omega Co., U.S.A.). To simulate typical clinical conditions, 35mm square samples of bovine scapular bone were utilized. The samples were approximately 20mm thick with the cortical thickness on the drilling side ranging from 1 to 2mm. A sample was placed in a container of saline solution so that its lower half is submerged into the solution and the upper half exposed to the room air, which averaged $24.9^{\circ}C$. The temperature of the saline solution was maintained at $36.5^{\circ}C$ using an electric heater (J. O Tech Co., Korea). This experimental condition was similar to that of a patient s opened mouth. The study revealed that a 2mm twist drill required greatest attention. As a guide drill, a twist drill is required to bore through a 'virgin bone,' rather than merely enlarging an already drilled hole as is the case with other drills. This typically generates greater amount of heat. Furthermore, one tends to apply a greater pressure to overcome drilling difficulty, thus producing even greater amount heat. 150 experiments were conducted for 2mm twist drill. For 140 cases, drill pressure of 750g was sufficient, and 10 cases required additional 500 or 100g of drilling pressure. In case of the former. 3 of the 140 cases produced the temperature greater than $47^{\circ}C$, the threshold temperature of degeneration of bone tissue (1983. Eriksson et al.) which is also the reference temperature in this study. In each of the 10 cases requiring extra pressure, the temperature exceeded the reference temperature. More significantly, a surge of heat was observed in each of these cases This observations led to addtional 20 drilling experiments on dense bones. For 10 of these cases, the pressure of 1,250g was applied. For the other 10, 1.750g were applied. In each of these cases, it was also observed that the temperature rose abruptly far above the thresh old temperature of $47^{\circ}C$, sometimes even to 70 or $80^{\circ}C$. It was also observed that the increased drilling pressure influenced the shortening of drilling time more than the rise of drilling temperature. This suggests the desirability of clinically reconsidering application of extra pressures to prevent possible injury to bone tissues. An analysis of these two extra pressure groups of 1,250g and 1,750g revealed that the t-statistics for reduced amount of drilling time due to extra pressure and increased peak temperature due to the same were 10.80 and 2.08 respectively suggesting that drilling time was more influenced than temperature. All the subsequent drillings after the drilling with a 2mm twist drill did not produce excessive heat, i.e. the heat generation is at the same or below the body temperature level. Some of screw tap, pilot, and countersink showed negative correlation coefficients between the generated heat and the drilling time. indicating the more the drilling time, the lower the temperature. The study also revealed that the drilling time was increased as a function of frequency of the use of the drill. Under the drilling pressure of 750g, it was revealed that the drilling time for an old twist drill that has already drilled 40 times was 4.5 times longer than a new drill The measurement was taken for the first 10 drillings of a new drill and 10 drillings of an old drill that has already been used for 40 drillings. 'Test Statistics' of small samples t-test was 3.49, confirming that the used twist drills require longer drilling time than new ones. On the other hand, it was revealed that there was no significant difference in drilling temperature between the new drill and the old twist drill. Finally, the following conclusions were reached from this study : 1 Used drilling bur causes almost no change in drilling temperature but increase in drilling time through 50 drillings under the manufacturer-recommended cooling conditions and the drilling pressure of 750g. 2. The heat that is generated through drilling mattered only in the case of 2mm twist drills, the first drill to be used in bone drilling process for all the other drills there is no significant problem. 3. If the drilling pressure is increased when a 2mm twist drill reaches a dense bone, the temperature rises abruptly even under the manufacturer-recommended cooling conditions. 4. Drilling heat was the highest at the final moment of the drilling process.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.3
• /
• pp.75-85
• /
• 2009

This work proposes a 13b 100MS/s 0.13um CMOS ADC for 3G communication systems such as two-carrier W-CDMA applications simultaneously requiring high resolution, low power, and small size at high speed. The proposed ADC employs a four-step pipeline architecture to optimize power consumption and chip area at the target resolution and sampling rate. Area-efficient high-speed high-resolution gate-bootstrapping circuits are implemented at the sampling switches of the input SHA to maintain signal linearity over the Nyquist rate even at a 1.0V supply operation. The cascode compensation technique on a low-impedance path implemented in the two-stage amplifiers of the SHA and MDAC simultaneously achieves the required operation speed and phase margin with more reduced power consumption than the Miller compensation technique. Low-glitch dynamic latches in sub-ranging flash ADCs reduce kickback-noise referred to the differential input stage of the comparator by isolating the input stage from output nodes to improve system accuracy. The proposed low-noise current and voltage references based on triple negative T.C. circuits are employed on chip with optional off-chip reference voltages. The prototype ADC in a 0.13um 1P8M CMOS technology demonstrates the measured DNL and INL within 0.70LSB and 1.79LSB, respectively. The ADC shows a maximum SNDR of 64.5dB and a maximum SFDR of 78.0dB at 100MS/s, respectively. The ABC with an active die area of $1.22mm^2$ consumes 42.0mW at 100MS/s and a 1.2V supply, corresponding to a FOM of 0.31pJ/conv-step.

• (The) Research of the performance art and culture
• /
• no.22
• /
• pp.253-285
• /
• 2011

The number of "Performing Arts Festivals" is growing increasingly in South Korea. This trend is mainly held in large cities which are difficult to communicate closely among residents. South Korea, while the pace of city life and speed of development are very fast, increasing number of "Performing Arts Festivals" with communal characteristics is in the natural process of festival evolution in large cities. In the evolution of the contemporary festival, it is natural to see some increase of modern festival after the development of traditional and folk festivals. It is important that the "Performing Arts Festivals" express the two elements, artistic character and festivity, not only in distinctively but also in harmony. The "Performing Arts Festivals" should consider the process of the organization, human resources, networking systems of the human communication process, resource use, etc. For the success of the festival, we must obtain the complementary effects between two attributes:festival characteristics and artistic senses. Therefore, we chose the 'Festival d'Avignon' as the reference of the total representation of artistic characteristics and festivity. From the case of the Festival d'Avignon, we get the implications of the development of performing arts festival in South Korea. To explain the festival value and artistic significance of the Festival d'Avignon, we explained the spontaneity and openness to public participation, the relationship between spectators and works, the representation of memory and communicative image, etc. To explain the artistic attributes of the 'Festival d'Avignon', we explained the mission to reconcile the artistic and the popular, to promote the artistic know-how, understanding how to communicate with the public, to consider more artistic quality than commercial benefits. Essentially, this study shows the meaning and the vision to forecast the future as well as the recent proliferation in various fields of Performing Arts Festivals. This study may help to improve analytical precision of Performing Arts Festivals.

• Asia Marketing Journal
• /
• v.13 no.4
• /
• pp.159-189
• /
• 2012

What attracts consumers to bloggers' reviews? Consumers would be attracted both by the Bloggers' expertise (i.e., knowledge and experience) and by his/her unbiased manner of delivering information. Expertise and trustworthiness are both virtues of information sources, particularly when there is uncertainty in decision-making. Noting this point, we postulate that consumers' motives determine the relative weights they place on expertise and trustworthiness. In addition, our hypotheses assume that tie strength moderates consumers' expectation on bloggers' expertise and trustworthiness: with expectation on expertise enhanced for power-blog user-group (weak-ties), and an expectation on trustworthiness elevated for personal-blog user-group (strong-ties). Finally, we theorize that the effect of credibility on willingness to accept a review is moderated by tie strength; the predictive power of credibility is more prominent for the personal-blog user-groups than for the power-blog user groups. To support these assumptions, we conducted a field survey with blog users, collecting retrospective self-report data. The "gourmet shop" was chosen as a target product category, and obtained data analyzed by structural equations modeling. Findings from these data provide empirical support for our theoretical predictions. First, we found that the purposive motive aimed at satisfying instrumental information needs increases reliance on bloggers' expertise, but interpersonal connectivity value for alleviating loneliness elevates reliance on bloggers' trustworthiness. Second, expertise-based credibility is more prominent for power-blog user-groups than for personal-blog user-groups. While strong ties attract consumers with trustworthiness based on close emotional bonds, weak ties gain consumers' attention with new, non-redundant information (Levin & Cross, 2004). Thus, when the existing knowledge system, used in strong ties, does not work as smoothly for addressing an impending problem, the weak-tie source can be utilized as a handy reference. Thus, we can anticipate that power bloggers secure credibility by virtue of their expertise while personal bloggers trade off on their trustworthiness. Our analysis demonstrates that power bloggers appeal more strongly to consumers than do personal bloggers in the area of expertise-based credibility. Finally, the effect of review credibility on willingness to accept a review is higher for the personal-blog user-group than for the power-blog user-group. Actually, the inference that review credibility is a potent predictor of assessing willingness to accept a review is grounded on the analogy that attitude is an effective indicator of purchase intention. However, if memory about established attitudes is blocked, the predictive power of attitude on purchase intention is considerably diminished. Likewise, the effect of credibility on willingness to accept a review can be affected by certain moderators. Inspired by this analogy, we introduced tie strength as a possible moderator and demonstrated that tie strength moderated the effect of credibility on willingness to accept a review. Previously, Levin and Cross (2004) showed that credibility mediates strong-ties through receipt of knowledge, but this credibility mediation is not observed for weak-ties, where a direct path to it is activated. Thus, the predictive power of credibility on behavioral intention - that is, willingness to accept a review - is expected to be higher for strong-ties.

• MISULJARYO - National Museum of Korea Art Journal
• /
• v.98
• /
• pp.22-53
• /
• 2020

This paper analyzes the contents, characteristics, and historical significance of the dedicatory inscriptions (josanggi) on the Amitabha Buddha and the Maitreya Bodhisattva statues of Gamsansa Temple, two masterpieces of Buddhist sculpture from the Unified Silla period. In the first section, I summarize research results from the past century (divided into four periods), before presenting a new perspective and methodology that questions the pre-existing notion that the Maitreya Bodhisattva has a higher rank than the Amitabha Buddha. In the second section, through my own analysis of the dedicatory inscriptions, arrangement, and overall appearance of the two images, I assert that the Amitabha Buddha sculpture actually held a higher rank and greater significance than the Maitreya Bodhisattva sculpture. In the third section, for the first time, I provide a new interpretation of two previously undeciphered characters from the inscriptions. In addition, by comparing the sentence structures from the respective inscriptions and revising the current understanding of the author (chanja) and calligrapher (seoja), I elucidate the possible meaning of some ambiguous phrases. Finally, in the fourth section, I reexamine the content of both inscriptions, differentiating between the parts relating to the patron (josangju), the dedication (josang), and the prayers of the patrons or donors (balwon). In particular, I argue that the phrase "for my deceased parents" is not merely a general axiom, but a specific reference. To summarize, the dedicatory inscriptions can be interpreted as follows: when Kim Jiseong's parents died, they were cremated and he scattered most of their remains by the East Sea. But years later, he regretted having no physical memorial of them to which to pay his respects. Thus, in his later years, he donated his estate on Gamsan as alms and led the construction of Gamsansa Temple. He then commissioned the production of the two stone sculptures of Amitabha Buddha and Maitreya Bodhisattva for the temple, asking that they be sculpted realistically to reflect the actual appearance of his parents. Finally, he enshrined the remains of his parents in the sculptures through the hole in the back of the head (jeonghyeol). The Maitreya Bodhisattva is a standing image with a nirmanakaya, or "transformation Buddha," on the crown. As various art historians have pointed out, this iconography is virtually unprecedented among Maitreya images in East Asian Buddhist sculpture, leading some to speculate that the standing image is actually the Avalokitesvara. However, anyone who reads the dedicatory inscription can have no doubt that this image is in fact the Maitreya. To ensure that the sculpture properly embodied his mother (who wished to be reborn in Tushita Heaven with Maitreya Bodhisattva), Kim Jiseong combined the iconography of the Maitreya and Avalokitesvara (the reincarnation of compassion). Hence, Kim Jiseong's deep love for his mother motivated him to modify the conventional iconography of the Maitreya and Avalokitesvara. A similar sentiment can be found in the sculpture of Amitabha Buddha. To this day, any visitor to the temple who first looks at the sculptures from the front before reading the text on the back will be deeply touched by the filial love of Kim Jiseong, who truly cherished the memory of his parents.