• Composites Research
• /
• 제20권1호
• /
• pp.23-31
• /
• 2007

Jute fiber Green Composite의 기계적 향상을 위한 계면특성을 향상시키기 위하여 커플링제를 도입하여 첨가량에 따른 특성변화를 실험적으로 규명하였다. Maleic anhydride grafted popolypropylene(MAPP)는 자연섬유와의 계면특성의 향상에서 물리화학적 역할을 하는 것으로 판단된다. MAPP에 의한 용융상태에서의 낮아진 수지의 점도는 흐름성이 향상되어 섬유의 계면과의 접촉 면적을 확대시킨다. 약 80mm의 jute 장섬유 mat에 maleated coupler가 혼합된 PP 복합재의 물성 향상과 열가소성수지의 물리적 변화와의 관계를 고찰하였다. 이 물리적 현상을 유동지수(MI: Melting flow index) 및 점도, contact angle, 복합재료 두께, 계면전단강도, morphology 분석 등의 인자들을 이용하여 기계적 물성 향상에 기여하는 정도를 확인하였다. 특히 유동지수(MI)와 점도, MAPP의 혼합량은, 전당강도(IFSS), 인장 및 굴곡 강도와 인장탄성률의 향상과 매우 관계가 있음을 실험 결과를 통하여 확인하였다.

• 전기학회논문지
• /
• 제57권1호
• /
• pp.46-51
• /
• 2008

Extra-high voltage(EHV) disconnecting switch(DS) consists of the electrical contacts and mechanical parts which actuate the contacts. When the short-circuit condition occurs, a large amount of current flows through the electrical contact in disconnecting switches and this causes considerable temperature rise due to Joule heating. If the temperature rise is higher than the melting point of contact material, the DS contact becomes melting and cannot be usable anymore. For this reason, the analysis for capability of carrying short-circuit current in DS contacts must be performed at a design stage. Here, we proposed a numerical technique for evaluating the capability of carrying short-circuit current at electrical contacts in EHV DS. In this numerical approach, the mechanical and thermal analyses were simulated to check the capability of carrying short-circuit current. First, the applied pressure at contact parts was analyzed considering the mechanical properties, and then contact resistance was calculated by an empirical equation. Finally, thermal analysis was performed with resistance variation at electrical contacts. To verify these numerical results, the distributions of temperature in DS were experimentally measured and compared with each other. The results from experiments were agreed well with those from the proposed numerical simulations.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제28회 KOSCO SYMPOSIUM 논문집
• /
• pp.149-157
• /
• 2004

In the present paper we studied experimentally fundamental optimization of oxygen enriched pyrolysis melting incinerator, Characteristics of this system was confirmed dealing with the gas flow and combustion properties for the inside secondary air injection. The experiment setup has a disposal rate of 30kg/hr which was measured by the inside temperature and gas. Along with above experiments, the three-dimensional computation was employed to analyse the combustion fluid dynamics and gas residence time. Equations for turbulence and heat - transmission as well as chemical reactions were solved by using common codes. The experimental combustion chamber was composed of staged combustion types structure for reducing NOx. Finally, it was verified that the control of the secondary air and air ratio of thermo stack were important. In the computational analysis, it showed reasonable agreement with the experimental results regarding the temperature and discharged gas concentration.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 영호남 학술대회 논문집
• /
• pp.48-52
• /
• 2003

Low melting crystalline solder glasses for CRT sealing were prepared from the composition of PbO 73.0~75.5 wt%, ZnO 12~15 wt%, $B_2O_3$ 7.0~9.0 wt%, BaO 1.5~3.5 wt%, $P_2O_5$ 1.0~2.5 wt%, $Bi_2O_3$ 0.5~20 wt%. The nucleation and crystallization of the crystalline solder glasses were studied by DTA, SEM and XRD. $2PbO{\cdot}ZnO{\cdot}B_2O_3$ crystalline phase was formed from glass matrix by heat-treatment of glass frits Crystalline solder glasses developed from this paper have good firing condition of $430{\sim}440^{\circ}C$ for 10min and good physical properties

• 태양에너지
• /
• 제6권2호
• /
• pp.43-53
• /
• 1986

The objective of this study is to report on the characterics of convective flow and heat transfer during metling process in order to provide design information for thermal energy storage systems which use phase change material. In present study, flow and heat transfer characteristics of the Phase Change Material in the Open Top Model (O.T.M) and in the Closed Top Model (C.T.M) were studied numerically by the control volume formulation using the algebraic non-orthogonal coordinate transformation. For the calculation procedure, the physical properties of fluid are assumed to be constant except density which is linely dependent on temperature in the bouyancy term of momentum equations. At start of melting process, the thickness of melting layer is assumed from the Stefan Problem assumption. The heat transfer results of Open Top Model and Closed Top Model are compared with the parameters of Grashof number and aspect ratio. It was found that heat transfer phenomena in melted region was greatly affected by buoyancy-driven natural convection and the melting distance of Open Top Model at the upper region is greater than that of Closed Top Model.

• 한국조명전기설비학회지:조명전기설비
• /
• 제11권6호
• /
• pp.74-80
• /
• 1997

본 논문에서는 저압 배전용 전선퓨즈의 I-t 특성을 다루었다. 전선퓨즈 엘리먼트는 과전류 영역을 담당하는 낮은 온도 용융영역(LTME)과, 대전류 영역을 담당하는 높은 온도 용융영역(HTME)으로 나누어 진다. 이들부분에 의하여 퓨즈의 용단특성이 결정되는 것이다. 따라서 이들 부분에 대한 열적, 전기적인 특성을 시뮬레이션하므로서, 퓨즈 엘리먼트 설계의 타당성을 이론적으로 검증하였다. 유한요소법(Finite Element Method)을 이용하여 전선퓨즈의 I-t특성을 시뮬레이션 하였다. 그리고 시뮬레이션 결과와 실혐결과를 비교해 보았을 때 대전류영역과 소전류영역에서의 상당히 유사한 결과를 얻을 수 있었다.

• Nuclear Engineering and Technology
• /
• 제51권6호
• /
• pp.1589-1595
• /
• 2019

In this paper, the CLAM steel strengthened by micro-scale Y-Zr-O was prepared by vacuum induction melting followed by electroslag remelting (VIM-ESR). Yttrium (Y) and zirconium (Zr) were easy to aggregates into massive yttrium-zirconium-rich inclusions in the steel melted by vacuum induction melting (VIM), which would interrupt the continuity of the matrix and reduce the mechanical properties of steel. Micron-sized Y-Zr-O inclusions would be produced with the removal of original blocky Y-Zr-rich inclusions and the submicron-sized inclusions smaller than $0.2{\mu}m$ could be retained in the steel. The small grain size and the better refinement and distribution uniformity of Y-Zr-O inclusions after remelting would be responsible for the better yield strength and toughness. For VIM-ESR alloy, the ultimate tensile strength is 749 MPa and the yield strength is 642 MPa at room temperature, meanwhile they are 391 MPa and 367 MPa at $600^{\circ}C$, respectively. Meanwhile, the ductile-brittle transition temperature (DBTT) reduced from $-43^{\circ}C$ (VIM) to $-76^{\circ}C$ (VIM-ESR).

• 한국분말재료학회지
• /
• 제29권1호
• /
• pp.1-7
• /
• 2022

This study investigates the effect of process stopping and restarting on the microstructure and local nanoindentation properties of 316L stainless steel manufactured via selective laser melting (SLM). We find that stopping the SLM process midway, exposing the substrate to air having an oxygen concentration of 22% or more for 12 h, and subsequently restarting the process, makes little difference to the density of the restarted area (~ 99.8%) as compared to the previously melted area of the substrate below. While the microstructure and pore distribution near the stop/restart area changes, this modified process does not induce the development of unusual features, such as an inhomogeneous microstructure or irregular pore distribution in the substrate. An analysis of the stiffness and hardness values of the nano-indented steel also reveals very little change at the joint of the stop/restart area. Further, we discuss the possible and effective follow-up actions of stopping and subsequently restarting the SLM process.

• 설비공학논문집
• /
• 제9권2호
• /
• pp.171-179
• /
• 1997

During the day time in summer, peak of air conditing load, and electric power management system lies under overloaded condition. The reason is the enlarged peak load value of electric power caused by increased air-cooling load in summer. To prevent load concentration during day time and overloaded condition of power management system, some energy storage methods are suggested. One of these methods is ice storage system. Water has some good properties as P.C.M.(Phase Chang Material) : Its melting point is the range of required operation temperature. It has large specific latent heat and is chemically stable compared to other organic or inorganic substances. It is cheap and easy to treat. This study represents experimental results of heat transfer characteristics of P.C.M. under the outward melting process in a vertical cylinder. We experimented with twelve combinations of conditions, i.e., three different inlet temperatures($7^{\circ}C,\;4^{\circ}C\;and\;1^{\circ}C$), two working fluid directions(upward and downward), and two aspect ratios, H/R(4 and 2). At the inlet temperature of $7^{\circ}C$ and $4^{\circ}C$, there was temperature stagnation region where the temperature of P.C.M. remains constant at $4^{\circ}C$ regardless of aspect ratio and direction of working fluid. This temperature stagnation occurs as the water, at its maximum density, flows down to the lower region. The phase change interface formed bell-shaped curve as the melting process continued. With a new set of conditions(4H/R, inlet temperature $4^{\circ}C$ and $1^{\circ}C$, downward/upwerd inlet direction), the movement of phase change interface was faster when the working flued inlet direction was downward. With the same set of conditions, melting rate and total melting energy were larger when the working fluid inlet direction was downward. The results were reversed when the other sets of conditions were applied.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.126-128
• /
• 2004

Welding or joining of dissimilar material is difficult and have limitations because physical properties of each material like melting temperature, heat expansion coefficient, conductivity, yielding point, etc. are different. (omitted)