• 소성∙가공
• /
• 제10권1호
• /
• pp.30-34
• /
• 2001

The magnetic and metallurgical characteristics of Mischmetal(MM) -Ferroboron (FeB) Permanent magnets have been investigated by X-ray diffractometer, scanning and transmission electron microscope and vibrating sample magnetometer under hot-pressing and die-upsetting process. The best magnetic properties obtained in these studies were $H_c$=5.8 kOe, $B_r$=5.0 kG with $(BH)_{max}=7.6 MGOe for melt-spun ribbons, $H_c$=3.0 kOe, $B_r$=4.6 kG with $(BH)_{max}$=2.9 MGOe for hot-pressed magnets and $H_c$=1.8 kOe, $B_r$=5.5 kG with $(BH)_{max}$=4.1 MGOe for die-upset magnets. The higher magnetic properties in die-upset magnets were resulted from alignment of the c-axis along the die-upsetting direction.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.687-689
• /
• 1995

Our team works on mixture of hard magnetic materials. As hard magnetic material we used mixture of powders: melt-spun ribbon Nd-Fe-B, ferrite and Alnico. Their different mixtures are basic material for dielectromagnets under our investigation. Main disadvantage of dielectromagnets with Nd-Fe-B alloy powder as a component is a low corrosion resistance. Protection against corrosion is covering dielectromagnets with metallic or organic coating film. The coating film protects dielectromagnets from free particles on the surface and low resistance for mechanical stresses too. The surface of dielectromagnets prepared from mixture of powders if formed by metallic particles - powder of Nd-Fe-B and Alnico, particles of oxide - powder of ferrite and particles of resin - bonding materials. Team work on technology of laying the metallic coating on dielectromagnets prepared from mixture of mentioned powders. Papers show the results of initial investigation on metallic coating technology. It shows influence of type and used technology of the metallic coating film on magnetic properties of dielectromagnets.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.824-827
• /
• 1995

Dielectromagnets are permanent magnets made from resin-bonded hard magnetic powders. Magnetic properties of dielectromagnets depend on kind of used hard magnetic materials as chemical compound, shape, size of grain and applied technology. Comparison of advantages and disadvantages of dielectromagnets made from different kind of magnetic powders induced us to try to prepare dielectromagnets from mixture of hard magnetic powders, not only one of them. The purpose of investigation on this kind of dielectromagnets is to find formula to prepare permanent magnets with properties adequate to different kind of electrical motors requirements. As hard magnetic materials we used powders of ferrite, melt-spun ribbon Nd-Fe-B and Alnico. Papers present results of investigation on technology of this kind of dielectromagnets. It shows also influence of kind of mixture and used technology on magnetic properties of dielectromagnets.

• 전기화학회지
• /
• 제4권3호
• /
• pp.104-108
• /
• 2001

용융분사법으로 나프탈렌계 메조페이스 피치(mP)를 방사하여 산화안정화 속도를 변화시켜 흑연화 섬유의 모폴러지를 제어하였으며, 흑연화 섬유를 이용하여 Li-ion 이차전지 부극을 제조하여 충$\cdot$방전 거동 및 용량을 측정하였다. 용융분사조건에 따라 제조된 피치섬유의 직경은 $4{\mu}m$로부터 $16{\mu}m$까지 다양하였다 이중에서 직경 $10{\mu}m$인 피치섬유를 선택하여 세가지 승온속도 조건 $2^{\circ}C/min,\;5^{\circ}C/min,\;10^{\circ}/min$에서 산화안정화 후 $1000^{\circ}C$에서 탄소화하여 $2650^{\circ}C$에서 흑연화 한 결과, 섬유 단면이 산화안정화 조건 $2^{\circ}C/min$의 경우는 라디알 구조, $5^{\circ}C/min$의 것은 라디알-랜덤 구조, $10^{\circ}C/min$의 경우는 skin-core 구조를 형성하였고, 승온속도가 큰 경우일수록 이흑연화성이 컷다. 이것은 큰 승온속도에서는 탄소화$\cdot$흑연화 과정에서 섬유표면에서만 산화안정화가 일어나고, 내부에서는 피치분자가 유동성이 커 승온과정에서 고결정성의 흑연구조가 발달한 것으로 추측된다. 따라서 이흑연화성이 큰 $10^{\circ}C/min$에서 산화안정화 한 것이 충전방전 용량이 $2^{\circ}C/min$의 경우에 비해서 1.3배로 약 400mAh/g, 충방전 효율도 $96.8\%$로 가장 우수한 특성을 나타냈다.

• 한국자기학회지
• /
• 제1권2호
• /
• pp.60-68
• /
• 1991

급속냉각기술로 제조된 $Nd_{14}Fe_{76}Co_{4}B_{6}$ 및 $Nd_{10.5}Fe_{79}Co_{2}Zr_{15}B_{7}$ 자성분말을 사용하여 성형체와 본드자석을 제조하였다. 자기특성, 최적충진률 등의 분말입도 및 형상비에 따른 거동은 합금조성에 따라 달리 나타난다. Co/Fe 비가 작은 저밀도의 $Nd_{10.5}Fe_{79}Co_{2}Zr_{1.5}B_{7}$ 합금이 같은 성형압력에서 성형체의 성형밀도 및 최적충진률이 높아 자기특성이 우수하였으나 반면에 분말입도에 따라 자기특성이 변화하였다. 성형밀도(p)와 성형압력(P) 사이 에는 ${\phi}(g/cm^{2})=5.2~5.6{\times}P^{0.045~0.065}(ton/cm^{2})$의 관계식이 성립된다. 높은 Nd/Fe 비를 갖는 급속냉각된 $Nd_{14}Fe_{76}Co_{4}B_{6}$ 합금의 초미세립(50~60 nm)으로써 높은 보자력($iH_{c}=14~15kOe$)을 보유하나, Nd/Fe비가 낮은 $Nd_{10.5}Fe_{79}Co_{2}Zr_{1.5}B_{7}$ 합금은 결정립이 조대하고(150~400 nm)Nd-rich한 입경계상의 발달이 부진하여 자벽고착기구가 주 보자력 기구 로 판명된 두 합금에서 고착지점으로서의 역할이 불충분하여 보자력이 낮은 것으로 판명되었다.

• 한국주조공학회지
• /
• 제29권2호
• /
• pp.64-69
• /
• 2009

In the present study the effect of cooling rate during solidification on the microstructural characteristics of Al-xAg (x = 31, 33, 35 at.%) in-situ binary eutectic composites has been investigated. To provide a wide range of cooling rate three different casting techniques, i.e. conventional casting, injection casting, and melt spinning have been used. The observed microstructure is very much dependent on the cooling rate. The fcc ${\alpha}$-Al and hcp $Ag_2Al$ phases exhibits an orientation of (111)Al//(0001)$Ag_2Al$, [1-10]Al//[11- 20]$Ag_2Al$. The microstructure of the melt-spun samples contains Widmanstatten structure resulting from solid-state transformation and nano scale two-phase structure resulting from solid-state phase separation. The microstructure of injection-cast samples contains eutectic structure and solid state phase-separated structure. On the other hand, conventional-cast samples exhibit a microstructure consisted of plate-type eutectic structure.

• 수산해양기술연구
• /
• 제46권3호
• /
• pp.257-264
• /
• 2010

In order to improve the breaking strength and elongation of Polybutylene succinate (PBS) monofilament, the monofilament was produced by blending PBS and Polybutlyne adipate-co-terephthalate (PBAT). The PBS/PBAT blend monofilament was prepared by the melt spinning system, and the weight ratios of the compositions of PBS/PBAT was 100/0, 95/5, 90/10 and 85/15, respectively. The breaking strength, elongation, softness and crystallization of PBS/PBAT blend monofilament were analyzed by using a tensionmeter, softness measurement, X-ray diffractometer in the both dry and wet conditions. The PBS/PBAT blend monofilaments were spun in the take-up velocity of 1.19m/sec under the drawing ratio of 6.8:1 condition. The production volumes of PBS/PBAT blend monofilaments showed 20% less than that of Nylon. The breaking strength of PBS/PBAT blend monofilaments were decreased as PBAT contents increased, while elongation and softness were increased. In case of PBAT content were over 5%, the breaking strength, elongation and softness of PBS/PBAT blend monofilaments were not shown to increase in spite of increasing in PBAT contents. Based on these results, it was possible to make the monofilaments with the maximized physical properties when the PBAT contents at 5%.

• Journal of Magnetics
• /
• 제9권4호
• /
• pp.101-104
• /
• 2004

The crystallization behaviours of nanocomposite made by a function of quenching rate (roller speed) were studied. The results showed that there was one step c$\mathbb{r}$ystallization process for the alloy quenched at roller speed of 32 m/s, which could be shown as, Am (amorphouse) + ${\alpha}-Fe/Nd_2Fe_{14}B$ ${\rightarrow}$ ${\alpha}-Fe/Nd_2Fe_{14}B$ . For the alloy quenched at roller speed of 40 m/s, there was steps crystallization process taking place at different temperatures, which could be shown as, Am ${\rightarrow}$ ${\alpha}-Fe/Nd_2Fe_{23}B_3+Nd_2Fe_{14}B+Am`$ ${\rightarrow}$ ${\alpha}-Fe/Nd_2Fe_{14}B$. The presence of transition phase ($Nd_2Fe_{23}B_3$) was harmful to get fine and uniform grain size during crystallization process. Uniform microstructures and high magnetic properties could be attained for the as-quenched alloy containing less amorphous phase and no presence of transition phase during annealing treatment. For the alloy prepared at roller speed of 32 m/s, the following properties were obtained, $B_r= 0.904 T,_iH_c = 801 kA/m, (BH)_{max} = 122 kJ/m^3 and M_r/M_s = 0.6$.

• 한국세라믹학회지
• /
• 제35권1호
• /
• pp.79-87
• /
• 1998

Melt spun YbBa2Cu3Agx(x=0, 5, 12, 16 and 53) precursor alloy ribbons were oxidized at 263-330$^{\circ}C$ and treated at 820$^{\circ}C$, 855$^{\circ}C$ and 885$^{\circ}C$ under 1.0 atm oxygen pressure. In the ribbons treated at 820$^{\circ}C$, 855$^{\circ}C$and 885$^{\circ}C$ 1-2-4 phase (YbBa2Cu4O8) and 1-2-3 phase (YbBa2Cu3O{{{{ OMICRON _7-$\delta$ }})were formed respectively. The shape of 1-2-4 phase was distorted or ellipsoid. The 2-4-7 and 1-2-3 phases tooked the shape of bar. All the ribbons showed zero critical current density Jc at 77K in zero magnetic field. By considering the shape and the highest critical temperature (among the three phases) of the 1-2-3 phase we tried to increase the critical current density of the ribbons treated at 885$^{\circ}C$ by press deformation. About tenribbons were stacked and coupled by press deformation and then treated at 885$^{\circ}C$ These 1-2-3 phase did not show any texture in any of the ribbons. However they exhibited weak texture in the multilayered specimens. Among the multilayered specimens YbBa2Cu3Ag16 exhibited a Jc of 180 A/cm2 Among the above ribbons YbBa2Cu3Ag16 ribbon has the optimum composition to produce textured superconducting oxide with improved Jc by press deformation. Onset critical temperatures Ton of the multilayered YbBa2Cu3Agx(x=5, 12, 16 and 53) were measured as 88-90 K.

• 한국분말재료학회지
• /
• 제16권1호
• /
• pp.33-36
• /
• 2009

In order to increase the magnetic loss for electromagnetic(EM) wave absorption, the soft magnetic $Fe_{73}Si_{16}B_7Nb_3Cu_1$(at%) alloy strip was used as the basic material in this study. The melt-spun strip was pulverized using an attrition mill, and the pulverized flake-shaped powder was crystallized at $540^{\circ}C$ for 1h to obtain the optimum grain size. The Fe-based powder was mixed with 2 wt% $BaTiO_3$, $0.3{\sim}0.6$ wt% carbon black, and polymer-based binders for the improvement of electromagnetic wave absorption properties. The mixture powders were tape-cast and dried to form the absorption sheets. After drying at $100^{\circ}C$ for 1h, the sheets of 0.5 mm in thickness were made by rolling at $60^{\circ}C$, and cut into toroidal shape to measure the absorption properties of samples. The characteristics including permittivity, permeability and power loss were measured using a Network Analyzer(N5230A). Consequently, the properties of electromagnetic wave absorber were improved with the addition of both $BaTiO_3$ and carbon black powder, which was caused by the increased dielectric loss of the additive powders.