• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.368-372
• /
• 2003

There arc two methods to evaluate the combustion product, that is analysis method and measurement method. Properties of the combustion products, constituents, and quanties, can be used to calculate boiler efficiency and beat losses. Using combustion evaluation methods combustion calculation were performed at certain condition and analyze the results. In this paper by comparing the results between two methods, deviation, correction and possibility of site application were confirmed

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.346.2-346.2
• /
• 2014

To use the GaN based light-emitting diodes (LEDs) as solid state lighting sources, the improvement of light extraction and internal quantum efficiency is essential factors for high brightness LEDs. In this study, we suggested the new materials system of a zinc tin oxide (ZTO) layer formed on blue LED epi-structures to improve the light extraction. ZTO is a representative n-type oxide material consisted of ZnO and SnO system. Moreover, ZTO is one of the promising oxide semiconductor material. Even though ZTO has higher chemical stability than IGZO owing to its SnO2 content this has high mobility and high reliability. After formation of ZTO layer on p-GaN layer by using the spin coating method, structural and optical properties are investigated. The x-ray diffraction (XRD) measurement results show the successful formation of ZTO. The photoluminescence (PL) and absorption spectrum shows that it has 3.6-4.1eV band gap. Finally, the light extraction properties of ZTO/LED chip using electroluminescence (EL) measurement were investigated. The experimental and theoretical analyses were simultaneously conducted.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.455-455
• /
• 2000

A novel pulse-width-modulated (PWM) function is introduced for precise position measurement in an enclosed signal field. An amplitude modulation was used to light the LEDs for the conventional study. However, the transform properties from the driving signal to the lighting intensities of the LEDs are non-linear, and accurate control of the lighting power was necessary. Therefore, a lighting function independent of these properties is desired. Well-known PWM functions are used to construct the enclosed signal field by simulation, and the precision of the phase detecting system is analyzed. A novel "axial symmetry PWM" function is found to be effective for orthogonal pahse detection.

• Journal of KSNVE
• /
• v.10 no.6
• /
• pp.949-954
• /
• 2000

Applicability of the vibration signal phase for predicting the modal damping properties of structures is investigated. For uniform plates with different internal damping levels, the phase delay as a function of the frequency span as well as a function of the distance between the excitation and response measurement points are experimentally obtained. Dependence of the phase characteristics on the amount of structural damping is elucidated -more heavily damped plate shows notably reduced phase delay at intermediate distances. The experimental results compare favorably with analytical predictions, and show much promise for further refinement as a tool for estimating structural properties.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.1
• /
• pp.54-61
• /
• 1998

Since Cr-Mo-V steel has excellent fracture and creep properties at elevated temperature, they are extensively used as steam turbine components such as the turbine rotor. However, the turbine rotor steel used to suffer material degradation during long term service. Therefore, the assessment of the safety and residual life of the turbine rotor is periodically required during service. One of the most convenient techniques for that is the hardness method mainly due to its simplicity and nondestructive characteristics. In this research, six specimens with different aging times of turbine rotor steel were artificially prepared by an isothermal heat treatment at $630^{\circ}C$. The micro Vickers hardnesses of specimens were measured at room temperature. The relationships between the fracture properties and the hardness ratio were investigated. And also an indirect method to evaluate the residual life of degraded turbine rotor was proposed based on the micro Vickers hardness measurement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.550-554
• /
• 2014

Regarding thin films in MEMS/NEMS structures, the exact evaluation of mechanical properties is very essential to enhance the reliability of their design and manufacturing. However, such methods as a tensile test and a resonance test, general methods to measure elastic moduli, cannot be applied to thin films since its thickness is so small. This work concerns guided wave based elastic modulus measurement method. To this end, guided wave excitation and detection system using a pulsed laser and a laser interferometry has been established. Also an elastic modulus extraction algorithm from the measured guided wave signal was developed. Finally, it was applied to actual thin film structures such as Ni-Si and Al-Si multilayers. From experimental results, we confirm that the proposed method has considerable feasibility to measure elastic properties of thin films.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.257-260
• /
• 2003

Bi-2223 tape is one of the most widely used HTS tapes for power application. This paper presents the basic properties such as temperature and resistivity rise of the Bi-2223 tape which is exposed to the over current. Temperature and resistivity were measured by E-type thermocouple and voltage taps. Results of the measurement showed that rise of voltage depended on the magnitude of the over current until several times of the rated current. When the current largely exceeded the rated current, rise of voltage depended on the magnitude of the resistivity of the Ag matrix because temperature of the matrix increased to a great extend.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.4
• /
• pp.72-78
• /
• 1997

A free space transmission method using standard gain horn antennas in the frequency range from 9.0 to 10.5GHz is applied to determine the dielectric properties of grain such as rough rice ,brown rice and barley. The dielectric constant and loss factor, which depend on the moisture content of the wetted grain are obtained from the measured attenuation and phase shift by vector network analyzer. The moisture content of grain varied from 11 to 25% based on this wetted condition. The measured values of dielectric constants as a function of moisture density are compared with values of those obtained using he predicted model for estimating dielectric constants of grain. The effect of density fluctuation, high is an important parameter governing the dielectric properties of grain, on the dielectric constant and loss factor is presented. A new density-independent model in terms of measured attenuation an moisture density is proposed of reducing the effects of density fluctuation on the moisture content measurement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.11
• /
• pp.1010-1013
• /
• 2006

Hydrogenated Diamond-like carbon (DLC) films were Prepared by the radio frequency plasma enhanced chemical vapor deposition (RF PECVD) method on silicon substrates using methane $(CH_4)$ and hydrogen $(H_2)$ gas for the application to solid lubricant of MEMS devices. We have checked the influence of varying RF power on tribological properties of DLC film. We have checked their performance as two kinds of method such as FFM (Friction Force Microscope) and BOD (Ball-on Disk) measurement. The friction coefficients and the contact number of cycles to steady state decreased as the increase of RF power with FFM and BOD measurement, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.303-305
• /
• 1996

The electrical Properties of ZnO added TiO$_2$were investigated by using the complex impedance measurement and voltage-current source and measurement unit. The electrical conductivity of ZnO added TiO$_2$decrease with increasing the content of ZnO. The frequency-dependent Ac conductivity increase as frequency increase. Also, the trend of capacitances is similar to the AC conductivity. The semicircles of impedance spectrum increase with increasing ZnO contents. The decrease of electrical conductivity seems to be the effect of ZnO acceptor adding.