• 품질경영학회지
• /
• 제18권1호
• /
• pp.84-95
• /
• 1990

The objective of this study is to understand the effect of measurement-related investment. That is, this study aims at verifying the correlation between the measurement-related investment and inferiority rate of products by statistical analysis. The samples of this study are 376 industrial companies in Korea, and the research data was analysed on inferiority state of industrial companies with a measurement standard laboratory. The analysis was made by the elementary statistics, the correlation analysis and the regression analysis. The results are summarized as follows : First, the inferioriy rate of the industrial companies with a measurement standard laboratory was relatively lower than that of the other companies without the laboratory by statistical significance. Second, the increment on measurement-related investment had a negative correlation with the increment of inferiority rate, and the increase of measurement-related investment showed decrease of the inferiority rate by regression analysis.

• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.862-874
• /
• 1989

본 연구에서는 반경법 진원도 측정기의 회전정도와 편심에 의한 영향을 제거 하여 시험편의 형상오차와 측정기 자체의 오차특성을 분리함으로써 진원도 측정의 정도를 향상시킬 수 있는 방법에 대하여 검토하였다. 진원도의 표시법으로는 최근 최소영역법에 의해 규정되는 경우가 많으나 이는 일반적으로 많은 연산시간을 요구 하므로 비경제적인 면이 있다.

• 한국연소학회지
• /
• 제19권4호
• /
• pp.42-48
• /
• 2014

The emission standard of diesel engine on the construction equipment has been rapidly enhanced in advanced countries, because most of air pollutions was caused by construction equipment. So, all of the construction equipments will be tested for emission with standard measurement mode. But, the standard measurement mode of construction equipment is different for non-road and one for the road in korea. This study was conducted to measure emission characteristics of the construction equipment with changed standard measurement mode and to improvement the emissions experimentally.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.198-203
• /
• 1998

To acquire the high precision of profile for standard electrode of loss angle, it is needed ultraprecision machining technology like MEAP(Magnetic Electronic Abrasive Polishing) and the very high profile measurement technology which can measure a micro unit about the workpiece. So, in this paper, it was developed the measurement system of precision of profile using non-contactable sensor that was approximate sensor of capacitance type, because that is better than others in the electrical characteristics. And standard electrode of loss angle was machined by the MEAP machining technology. In this study, it was development of precision measurement system. This system could be used measure the workpiece of roundness and straightness much more precise and faster than general mechanical measurement system done before. And it could be helped to minimize machining time and planning by very fast and precise measurement about the workpiece.

• 지역사회간호학회지
• /
• 제17권4호
• /
• pp.573-582
• /
• 2006

Purpose: To find out whether the self-care ability measurement used for visiting health care provide an appropriate standard to select service methods using a Delphi survey and to offer basic data that can improve the measurement. Method: A Delphi survey was done with 39 people consisting of theoretical professionals, field managers, and practitioners engaged in visiting health care. Result: It was found that items and weighted points in the currently used self-care ability measurement needed adjustment. Therefore, a modified evaluation standard was presented by domains, items and detailed items. Finally, the self-care ability measurement is composed of 4 domains, 11 items and 19 detailed items. Conclusion: This study is significant in that it presented an evaluation standard applicable directly to business practice by supplementing problems in the existing self-care ability measurement. This study suggests the need to develop various measurements for elderly households based on community.

• 대한안전경영과학회지
• /
• 제9권1호
• /
• pp.145-156
• /
• 2007

This paper is to propose model classification and evaluation of measurement uncertainty. In order to obtain type A and B uncertainty, variety of measurement mathematical models are illustrated by example. The four steps to evaluate expanded uncertainty are indicated as following; First, to get type A standard uncertainty, measurement mathematical models of single, double, multiple, design of experiment and serial autocorrelation are shown. Second, to solve type B standard uncertainty measurement mathematical models of empirical probability distributions and multivariate are presented. Third, type A and B combined uncertainty, considering sensitivity coefficient, linearity and correlation are discussed. Lastly, expanded uncertainty, considering degree of freedom for type A, B uncertainty and coverage factor are presented with uncertainty budget. SPC control chart to control expanded uncertainty is shown.

• 한국의류학회지
• /
• 제27권1호
• /
• pp.88-99
• /
• 2003

The body changes of the elderly women are the forward tilt of the neck and shoulder point shrinkage of the spinal column, and protrusive abdomen. Unfortunately, few data based on body measurements for elderly women existed and a few studies are limited to the body figure of the elderly women. If these changes are not applied to the manufacturing of the clothing, almost of the elderly women will be unfitted with their clothing. So to improve the fitting of the elderly women, it is necessary to use the standard size systems for elderly women. This report is the first study to develop the standard tables of body measurements to be used for improving the fit of garments and patterns for women aged 60 and older. This study drew from anthropometric measurements of 337 and photographic measurements of 276 women aged 60 and older. It described the protocol of anthropometric measurement, the comparison between the measured data and the data on which National anthropometric survey of Korea 1997 is based, and the development of body measurement standard tables for elderly women. And we also considered the regional difference of body dimensions in order to develop the national size standards for elderly women. Further study would include the classification of body dimensions and description of each figure type for sizing apparel of women aged 60 and older.

• 대한기계학회논문집B
• /
• 제32권9호
• /
• pp.712-719
• /
• 2008

Light Oil Flow Standard System(LOFSS), as a national oil flow standard system, in Korea Research Institute of Standards and Science(KRISS) was developed for oil flowmeter calibration, and the expanded uncertainty of flow quantity determination was estimated within 0.04 %. In order to improve the reliability of the LOFSS measurement, a proficiency test was carried out in the flow range of 20 and $240\;m^3/h$ (Reynolds number $20,000{\sim}900,000$). A turbine flowmeter was used as a transfer package in round robin test. The water flow standard system of KRISS, the pipe prover of the national calibration and test organization and the master meter calibrator of the turbine flowmeter supplier, which used the different working fluid respectively, were compared with the turbine flowmeter measurement. The maximum difference of measurement was 0.15 % between the LOFSS and the pipe prover. The En numbers of the each system measurement were evaluated at the same Reynolds number. It was found that the En numbers were less than 1 in the comparison, which means the procedures of the uncertainty estimation of the each calibrators were reasonable and reliable.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.87-88
• /
• 2006

• 플랜트 저널
• /
• 제7권4호
• /
• pp.77-87
• /
• 2011

In proportion to continuing growth of overseas plant market and the trend of its mega scale of the project, the importance of management is significantly emphasized for the successful execution of the project. And it is recognized that progress control is the most important management item amongst the others in the management. Progress control is importance of progress measurement for performance measurement and process control of project, but it is hardly obtainable securing the objectivity in the progress measurement since the progress measurement are being applied differently in accordance with the project conditions and the experience level of the person in charge for the progress control. This study has conducted as following to propose a standard method for progress measurement in a petrochemical plant protect. Domestic and overseas plant projects are investigated variously with the applied method of progress measurement, and the deduced problem of progress measurement. And then standard method for progress measurement of engineering, procurement, construction and commissioning has been proposed according to comparison and analysis of practices in domestic & overseas plant project, procedures for progress control in the globally reputed petrochemical client, company rules and recommendation of the expert in progress control.