• Journal of Hydrogen and New Energy
• /
• v.9 no.4
• /
• pp.161-167
• /
• 1998

It has been investigated the effects of alloying elements and binders on the corrosion behavior of metal hydride electrodes for anode of Ni/MH secondary battery. The $AB_5$-type alloys, $(LM)Ni_{4.49}Co_{0.1}Mn_{0.205}Al_{0.205}$ and $(LM)Ni_{3.6}Co_{0.7}Mn_{0.3}Al_{0.4}$, were used for the experiments. The electrodes were prepared by mixing and cold-pressing of alloy powders with Si sealent or PTFE powders, or cold-pressing the electroless copper coated alloy powders. The amount of copper coating was 20wt%. In order to examine corrosion behavior of the electrodes, the corrosion current and the current density, in 6M KOH aqueous solution after removal of oxygen in the solution, were measured by potentiodynamic and cyclic voltamo methods. The results showed that Co in the alloy increased corrosion resistance of the electrode whereas Ni decreased the stability of the electrode during the charge-discharge cycles. The electrode used Si sealant as a binder showed a lower corrosion current density than the electrode used PTFE and the electrode used Cu-coated alloy powders showed the best corrosion resistance.

• Journal of the Korean Magnetics Society
• /
• v.23 no.2
• /
• pp.49-53
• /
• 2013

A current sensor is one of important component which is used for the electrical current measurement during charge and discharge of the battery, and monitoring system of the motor controller in the electric and hybrid vehicle. In this study, we have developed an open loop type current sensor using GaAs Hall sensor and magnetic core has an air gap. The Hall sensor detect magnetic field produced by the current to be measured. The 3 mm air gap core was made by HGO electrical steel sheets after slitting, winding, annealing, molding, and cutting. Developed current sensor shows 0.03 % linearity within DC current range from -400 A to +400 A. Operating temperature range was extended to the range of $-40{\sim}105^{\circ}C$ using temperature compensating electronic circuit. To Improve frequency bandwidth limit due to the air flux of PCB (Printed Circuit Board) and Hall sensor, We employed an air flux compensating loop near Hall sensor or on PCB. Frequency bandwidth of the sensor was 100 kHz when we applied sine wave current of $40A{\cdot}turn$ in the frequency range from 100 Hz to 100 kHz. For the dynamic response time measurement, 5 kHz square wave current of $40A{\cdot}turn$ was applied to the sensor. Response time was calculated time reach to 90 % of saturation value and smaller than $2{\mu}s$.

• Journal of Korea Water Resources Association
• /
• v.41 no.12
• /
• pp.1187-1198
• /
• 2008

Many reservoirs in Korea and their downstream environments are under increased pressure for water utilization and ecosystem management from longer discharge of turbid flood runoff compared to a natural river system. Turbidity($C_T$) is an indirect measurement of water 'cloudiness' and has been widely used as an important indicator of water quality and environmental "health". However, $C_T$ modeling studies have been rare due to lack of experimental data that are necessary for model validation. The objective of this study is to validate a coupled three-dimensional(3D) hydrodynamic and particle dynamics model (ELCOM-CAEDYM) for the simulation of turbid density flows in stratified Daecheong Reservoir using extensive field data. Three different groups of suspended solids (SS) classified by the particle size were used as model state variables, and their site-specific SS-$C_T$ relationships were used for the conversion between field measurements ($C_T$) and state variables (SS). The simulation results were validated by comparing vertical profiles of temperature and turbidity measured at monitoring stations of Haenam(R3) and Dam(R4) in 2004. The model showed good performance in reproducing the reservoir thermal structure and propagation of stream density flow, and the magnitude and distribution of turbidity in the reservoir were consistent with the field data. The 3D model and turbidity modeling framework suggested in this study can be used as a supportive tool for the best management of turbidity flow in other reservoirs that have similar turbidity problems.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.1 no.1
• /
• pp.29-35
• /
• 1999

Soil structure and organic matter have been known to strongly affect water flow and solute transport, yet little information is available concerning soil hydraulic properties related to soil physical and chemical properties in the forest site. The purpose of this study was to quantify the spatial variability and spatial correlation of the measured parameter values from the plots established with the rainfall simulator on Japanese larch(Larix leptolepis) dominated site in Kwangju. Kyunggi-Do. Measurement of soil water flux and retention were made with the inherent soil texture, soil structure, and organic matter. The method was based on the observation that when water was applied at a constant rate to the soil surface on each plot. The method was simple to apply and consists of following steps: (i) Wet the soil from a rainfall simulator with several known discharge rates on a relatively leveled soil surface with and without organic matter. (ii) Once the borders of the ponded zone were steady, saturated hydraulic conductivity( $K_{s}$) and the matric flux function(F) was evaluated from a regression of flux vs. the reciprocal of the ponded area. A conductivity of the form $K_{i+}$$_1$ $_{c}$= $K_{i}$( $_{c}$) [1-d /dz] where flux continuity implies. For this, continuity of matric potential at the interface at all times are as follows: $_1$( $Z_{c}$) = $_2$( $Z_{c}$) = $_{c}$ for steady state intake from water ponded on the soil surface. Results of this investigation showed the importance of understanding spatial variability in wide differences of water retention and saturated hydraulic conductivity with respect to pore geometry and organic matter contents which influenced the water flux throughout the soil profile.l profile.ile.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.2 no.2
• /
• pp.20-30
• /
• 1999

To improve water quality particularly for sea bathers along the Fylde coastal zone near Blackpool, North West England, waste water from a sewage outfall is studied using a mathematical model. The explicit second order accurate central scheme and the third order accurate QUICKEST scheme are used to represent the diffusion terms and the advection terms of the advective-diffusion equation, respectively. Hydrodynamic model is run for a coarse and fine grid, of 1km and 200m, respectively, obtaining good agreement with measured data. Water quality model is then used to predict faecal coliform levels in the region for four different scenarios, including discharges from: - (i) Fleetwood outfall, (ii)River Ribble for summer condition, (iii)River Ribble for winter condition, and (iv)combined sewer overflows for the Blackpool and Fleetwood communities. Main findings from the simulations are:- (i) Fleetwood outfall has a negligible impact on the beaches with respect to pathogen levels; (ii) Discharge from River Ribble for both summer and winter conditions is predicted in the range of coliform levels 10 -500 counts/100ml along the beach at Lytham St. Annes; and (iii) The CSO effluent discharges are predicted not to advect out into offshore by stronger tidal currents.

• Journal of the Korean Dietetic Association
• /
• v.22 no.4
• /
• pp.292-309
• /
• 2016

The purpose of this study was to verify the validity of Mealworms as a hospital meal with increased nutrition density. We provided a meal for postoperative patients and conducted analysis of dietary intake and nutritional status of patients and assessment of acceptability of the meal. This study was carried out as a randomized control trial. Patients were supplied either a hospital meal using Mealworms (Experimental group) or a regular hospital meal (Control group). We investigated the administration amounts of parenteral nutrition (PN) and food intake of patients after surgery and measured anthropometry, body composition, and blood tests before surgery and at hospital discharge. We included 34 postoperative patients who were admitted to Gangnam Severance Hospital from March to September. In the groups of patients not supplied with PN, the experimental group ($964.68{\pm}284.6kcal$, $38.82{\pm}12.9g$) had significantly higher dietary calorie and protein intake than the control group ($666.62{\pm}153.7kcal$, $24.47{\pm}4.9g$)(P<0.05). Additionally in the group of patients not supplied with PN, the experimental group (1.37%) showed a significantly higher increase in fat free mass index than the control group (-3.46%)(P<0.05). In all subjects, calorie density and protein density were significantly higher in the experimental group (P<0.001), and acceptability of calorie (P=0.036) and protein (P=0.001) was also significantly higher in the experimental group. Therefore, the results of this study support the validity of the introduction of hospital meals using Mealworms.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.6
• /
• pp.1029-1044
• /
• 2017

The Discrete Element Method (DEM) is one of the useful numerical methods to analyze the behavior of the ground formation by computing the motion and interaction using particles. The DEM has not been applied in civil engineering but also a wide range of industrial fields, such as chemical engineering, pharmacy, material science, food engineering, etc. In this study, to review a performance of the spoke-type earth pressure balance (EPB) shield TBM (Tunnel Boring Machine), the commercial software based on the DEM technology was used. An analysis of the TBM during excavation was conducted according to two pre-defined excavation conditions with the different rotation speed of a cutterhead. During the analysis, the resistant torque at the face of the cutterhead, the compressive force at the cutterhead and shield surface, the muck discharge at the screw auger were measured and compared. Upon the two kinds of excavation conditions, the applicability of the DEM analysis was reviewed as a modelling method for the TBM.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.230-238
• /
• 2014

In this paper, we propose the possible way of accurate analysis and examination of ITO sensor to discriminate whether mutual capacitance ITO sensor is defective by using mutual capacitance of data in each node which consists of electrodes inside of ITO sensor. We have analyzed the structure characteristic of mutual capacitance ITO sensor which is used as an input device for not only small size electronics like mobile phone and tablets but also big size electronics and designed the circuit to inspect ITO sensor using touch screen panel IC. Set a variable related with mutual capacitance of charge and discharge and Implement to find and analyze accurate position when defect is made through the data from each node of ITO sensor. First, we can set a yield effective range through the first experiment data of mutual capacitance ITO sensor and by using the data of each node of ITO sensor which is the result from the second experiment, we can verify accuracy and effectiveness of effective range from the first experiment as a sample which is used in this experiment.

• Clean Technology
• /
• v.14 no.3
• /
• pp.171-175
• /
• 2008

The effect of the addition of $Al^{3+}$ dopant on the electrochemical characteristics of $Li_{4}Ti_{5}O_{12}$ was investigated. $Li_{4}Ti_{5}O_{12}$ is known as a 2ero-strain material, and $Li_{3.95}Al_{0.15}Ti_{4.9}O_{12}$ has been manufactured by solid-state reaction with high energy ball milling (HEBM). The samples were heated at 800, 900 and $1000^{\circ}C$ in electric furnace. The structural and surface structures were measured by XRD (X-ray diffraction) and SEM (scanning electron microscopy). Cut-off voltage of charge/discharge cycles was $1.0{\sim}3.0 V$ to investigate reversible capacity, cycle stability and plateau voltage. The reversible capacity of $Li_{3.95}Al_{0.15}Ti_{4.9}O_{12}$ was 138 mAh/g.

• Journal of Periodontal and Implant Science
• /
• v.30 no.1
• /
• pp.11-27
• /
• 2000

The purpose of this study was to evaluate the clinical effects of Dipotassium glycyrrhizinate, Allantoin, Hinokitiol, Cetylpyridinium chloride containing gel($Dentheth^{(R)}$) on periodontitis. 41 patients with sites having pocket depth of 4-6mm were selected for the study. We classified 2 groups which consisted of 21 patients in the test group(exp.) and 20 patients in the control(placebo) respectively. Following a baseline examination, plaque and calculus were removed and then the experimental gel were handed out to the patients and topical application regimens were initiated. During the 4-week experimental period, pocket depth, bleeding on probing, gingival index, plaque index as a clinical parameters were measured in the baseline, 2 weeks, 4 weeks respectively. A questionnaire was delivered to each patients in 2 weeks, 4 weeks respectively. The results were as follows : 1. Probing pocket depth showed a significant difference in the Exp. group compared with the control group in the changes from baseline to 2 weeks(p<0.05), but there was no significant difference between the groups in the changes from baseline to 4 weeks, from 2 weeks to 4 weeks(p<0.05). 2. The Exp. group showed a significant difference compared with the control group in the changes from baseline to 2 weeks, from baseline to 4 weeks, from 2 weeks to 4 weeks in bleeding on probing(p<0.05). 3. The gingival index showed a significant difference compared with the control group in the changes from baseline to 2 weeks, from baseline to 4 weeks, from 2 weeks to 4 weeks after 4 weeks use of a gel(p<0.05). 4. The plaque index showed a significant difference in the Exp. group compared with the control group in the changes from baseline to 2 weeks(p<0.05), but there was no significant difference between the groups in the changes from baseline to 4 weeks, from 2 weeks to 4 weeks(p<0.05). 5. A questionnaire was consisted of 5 kinds as to bleeding, pus discharge, pain, burning sensation, patient's satisfaction and all of the questions showed a significant difference compared with the control group in the changes from 2 weeks to 4 weeks(p<0.05). 6. During the 4-week experimental period, important side-effects were not finded out, but each groups had one patient appealed nausea or discomfort respectively. These results indicate that application of periodontitis medical gel was useful as an additional aid of mechanical treatment.