• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.154-155
• /
• 2012

The promise of nano-crystalites (nc) as a technological material, for applications including display backplane, and solar cells, may ultimately depend on tailoring their behavior through doping and crystallinity. Impurities can strongly modify electronic and optical properties of bulk and nc semiconductors. Highly doped dopant also effect structural properties (both grain size, crystal fraction) of nc-Si thin film. As discussed in several literatures, P atoms or radicals have the tendency to reside on the surface of nc. The P-radical segregation on the nano-grain surfaces that called self-purification may reduce the possibility of new nucleation because of the five-coordination of P. In addition, the P doping levels of ${\sim}2{\times}10^{21}\;at/cm^3$ is the solubility limitation of P in Si; the solubility of nc thin film should be smaller. Therefore, the non-activated P tends to segregate on the grain boundaries and the surface of nc. These mechanisms could prevent new nucleation on the existing grain surface. Therefore, most researches shown that highly doped nc-thin film by using conventional PECVD deposition system tended to have low crystallinity, where the formation energy of nucleation should be higher than the nc surface in the intrinsic materials. If the deposition technology that can make highly doped and simultaneously highly crystallized nc at low temperature, it can lead processes of next generation flexible devices. Recently, we are developing a novel CVD technology with a neutral particle beam (NPB) source, named as neutral beam assisted CVD (NBaCVD), which controls the energy of incident neutral particles in the range of 1~300eV in order to enhance the atomic activation and crystalline of thin films at low temperatures. During the formation of the nc-/pm-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. In the case of phosphorous doped Si thin films, the doping efficiency also increased as increasing the reflector bias (i.e. increasing NPB energy). At 330V of reflector bias, activation energy of the doped nc-Si thin film reduced as low as 0.001 eV. This means dopants are fully occupied as substitutional site, even though the Si thin film has nano-sized grain structure. And activated dopant concentration is recorded as high as up to 1020 #/$cm^3$ at very low process temperature (＜ $80^{\circ}C$) process without any post annealing. Theoretical solubility for the higher dopant concentration in Si thin film for order of 1020 #/$cm^3$ can be done only high temperature process or post annealing over $650^{\circ}C$. In general, as decreasing the grain size, the dopant binding energy increases as ratio of 1 of diameter of grain and the dopant hardly be activated. The highly doped nc-Si thin film by low-temperature NBaCVD process had smaller average grain size under 10 nm (measured by GIWAXS, GISAXS and TEM analysis), but achieved very higher activation of phosphorous dopant; NB energy sufficiently transports its energy to doping and crystallization even though without supplying additional thermal energy. TEM image shows that incubation layer does not formed between nc-Si film and SiO2 under later and highly crystallized nc-Si film is constructed with uniformly distributed nano-grains in polymorphous tissues. The nucleation should be start at the first layer on the SiO2 later, but it hardly growth to be cone-shaped micro-size grains. The nc-grain evenly embedded pm-Si thin film can be formatted by competition of the nucleation and the crystal growing, which depend on the NPB energies. In the evaluation of the light soaking degradation of photoconductivity, while conventional intrinsic and n-type doped a-Si thin films appeared typical degradation of photoconductivity, all of the nc-Si thin films processed by the NBaCVD show only a few % of degradation of it. From FTIR and RAMAN spectra, the energetic hydrogen NB atoms passivate nano-grain boundaries during the NBaCVD process because of the high diffusivity and chemical potential of hydrogen atoms.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.22 no.1
• /
• pp.26-46
• /
• 2020

An irrigated-maize agroecosystem is viewed as an open thermodynamic system upon which solar radiation impresses a large gradient that moves the system away from equilibrium. Following the imperative of the second law of thermodynamics, such agroecosystem resists and reduces the externally applied gradient by using all means of this nature-human coupled system acting together as a nonequilibrium dissipative process. The ultimate purpose of our study is to test this hypothesis by examining the energetics of agroecosystem growth and development. As a first step toward this test, we employed the eddy covariance flux data from 2003 to 2014 at the AmeriFlux NE1 irrigated-maize site at Mead, Nebraska, USA, and analyzed the energetics of this agroecosystem by scrutinizing its radiation, energy and entropy exchange. Our results showed: (1) more energy capture during growing season than non-growing season, and increasing energy capture through growing season until senescence; (2) more energy flow activity within and through the system, providing greater potential for degradation; (3) higher efficiency in terms of carbon uptake and water use through growing season until senescence; and (4) the resulting energy degradation occurred at the expense of increasing net entropy accumulation within the system as well as net entropy transfer out to the surrounding environment. Under the drought conditions in 2012, the increased entropy production within the system was accompanied by the enhanced entropy transfer out of the system, resulting in insignificant net entropy change. Drought mitigation with more frequent irrigation shifted the main route of entropy transfer from sensible to latent heat fluxes, yielding the production and carbon uptake exceeding the 12-year mean values at the cost of less efficient use of water and light.

• Progress in Medical Physics
• /
• v.10 no.2
• /
• pp.63-71
• /
• 1999

For the purpose of utilization in 3-D conformal radiotherapy and whole body radiosurgery, the Whole Body 3-Dimensional Topographic Radiation Therapy System has been developed. Whole body frame was constructed in order to be installed on the couch. Radiopaque catheters were engraved on it for the dedicated coordinate system and a MeV-Green immobilizer was used for the patient setup by the help of side panels and plastic rods. By designing and constructing the whole body frame in this way, geometrical limitation to the gantry rotation in 3-D conformal radiotherapy could be minimized and problem which radiation transmission may be altered in particular incident angles was solved. By analyzing CT images containing information of patient setup with respect to the whole body frame, localization and coordination of the target is performed so that patient setup error may be eliminated between simulation and treatment. For the verification of setup, the change of patient positioning is detected and adjusted in order to minimize the setup error by means of comparison of the body outlines using 3 CCTV cameras. To enhance efficiency of treatment procedure, this work can be done in real time by watching the change of patient setup through the monitor. The method of image subtraction in IDL (Interactive Data Language) was used to visualize the change of patient setup. Rotating X-ray system was constructed for detecting target movement due to internal organ motion. Landmark screws were implanted either on the bones around target or inside target, and variation of target location with respect to markers may be visualized in order to minimize internal setup error through the anterior and the lateral image information taken from rotating X-ray system. For CT simulation, simulation software was developed using IDL on GUI(Graphic User Interface) basis for PC and includes functions of graphic handling, editing and data acquisition of images of internal organs as well as target for the preparation of treatment planning.

• The Mathematical Education
• /
• v.24 no.2
• /
• pp.105-116
• /
• 1986

For any thought and knowledge, its growth and development has close relation with the society where it is developed and grow. As Feuerbach says, the birth of spirit needs an existence of two human beings, i. e. the social background, as well as the birth of body does. But, at the educational viewpoint, the spread and the growth of such a thought or knowledge that influence favorably the development of a society must be also considered. We would discuss the goal and the function of mathematics education in relation with the prosperity of a technological civilization. But, the goal and the function are not unrelated with the spiritual culture which is basis of the technological civilization. Most societies of today can be called open democratic societies or societies which are at least standing such. The concept of rationality in such societies is a methodological principle which completes the democratic society. At the same time, it is asserted as an educational value concept which explains comprehensively the standpoint and the attitude of one who is educated in such a society. Especially, we can considered the cultivation of a mathematical thinking or a logical thinking in the goal of mathematics education as a concept which is included in such an educational value concept. The use of the concept of rationality depends on various viewpoints and criterions. We can analyze the concept of rationality at two aspects, one is the aspect of human behavior and the other is that of human belief or knowledge. Generally speaking, the rationality in human behavior means a problem solving power or a reasoning power as an instrument, i. e. the human economical cast of mind. But, the conceptual condition like this cannot include value concept. On the other hand, the rationality in human knowledge is related with the problem of rationality in human belief. For any statement which represents a certain sort of knowledge, its universal validity cannot be assured. The statements of value judgment which represent the philosophical knowledge cannot but relate to the argument on the rationality in human belief, because their finality do not easily turn out to be true or false. The positive statements in science also relate to the argument on the rationality in human belief, because there are no necessary relations between the proposition which states the all-pervasive rule and the proposition which is induced from the results of observation. Especially, the logical statement in logic or mathematics resolves itself into a question of the rationality in human belief after all, because all the logical proposition have their logical propriety in a certain deductive system which must start from some axioms, and the selection and construction of an axiomatic system cannot but depend on the belief of a man himself. Thus, we can conclude that a question of the rationality in knowledge or belief is a question of the rationality both in the content of belief or knowledge and in the process where one holds his own belief. And the rationality of both the content and the process is namely an deal form of a human ability and attitude in one's rational behavior. Considering the advancement of mathematical knowledge, we can say that mathematics is a good example which reflects such a human rationality, i. e. the human ability and attitude. By this property of mathematics itself, mathematics is deeply rooted as a good. subject which as needed in moulding the ability and attitude of a rational person who contributes to the development of the open democratic society he belongs to. But, it is needed to analyze the practicing and pursuing the rationality especially in mathematics education. Mathematics teacher must aim the rationality of process where the mathematical belief is maintained. In fact, there is no problem in the rationality of content as long the mathematics teacher does not draw mathematical conclusions without bases. But, in the mathematical activities he presents in his class, mathematics teacher must be able to show hem together with what even his own belief on the efficiency and propriety of mathematical activites can be altered and advanced by a new thinking or new experiences.

• Journal of Technology Innovation
• /
• v.26 no.3
• /
• pp.37-68
• /
• 2018

Since the 20th century, automobiles, which are the most common means of transportation, have been evolving as the use of electronic control devices and automotive semiconductors increases dramatically. Automotive semiconductors are a key component in automotive electronic control devices and are used to provide stability, efficiency of fuel use, and stability of operation to consumers. For example, automotive semiconductors include engines control, technologies for managing electric motors, transmission control units, hybrid vehicle control, start/stop systems, electronic motor control, automotive radar and LIDAR, smart head lamps, head-up displays, lane keeping systems. As such, semiconductors are being applied to almost all electronic control devices that make up an automobile, and they are creating more effects than simply combining mechanical devices. Since automotive semiconductors have a high data rate basically, a microprocessor unit is being used instead of a micro control unit. For example, semiconductors based on ARM processors are being used in telematics, audio/video multi-medias and navigation. Automotive semiconductors require characteristics such as high reliability, durability and long-term supply, considering the period of use of the automobile for more than 10 years. The reliability of automotive semiconductors is directly linked to the safety of automobiles. The semiconductor industry uses JEDEC and AEC standards to evaluate the reliability of automotive semiconductors. In addition, the life expectancy of the product is estimated at the early stage of development and at the early stage of mass production by using the reliability test method and results that are presented as standard in the automobile industry. However, there are limitations in predicting the failure rate caused by various parameters such as customer's various conditions of use and usage time. To overcome these limitations, much research has been done in academia and industry. Among them, researches using data mining techniques have been carried out in many semiconductor fields, but application and research on automotive semiconductors have not yet been studied. In this regard, this study investigates the relationship between data generated during semiconductor assembly and package test process by using data mining technique, and uses data mining technique suitable for predicting potential failure rate using customer bad data.

• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.12
• /
• pp.1141-1153
• /
• 2010

This paper introduces ONLIS(Overlay Multicast Network for Live IPTV Service), a novel overlay multicast network optimized to deliver live broadcast IPTV stream. We analyzed IPTV reference model of ITU-T IPTV standardization group in terms of network and stream delivery from the source networks to the customer networks. Based on the analysis, we divide IPTV reference model into 3 networks; source network, core network and access network, ION(Infrastructure-based Overlay Multicast Network) is employed for the source and core networks and PON(P2P-based Overlay Multicast Network) is applied to the access networks. ION provides an efficient, reliable and stable stream distribution with very negligible delay while PON provides bandwidth efficient and cost effective streaming with a little tolerable delay. The most important challenge in live P2P streaming is to reduce end-to-end delay without sacrificing stream quality. Actually, there is always a trade-off between delay & stream quality in conventional live P2P streaming system. To solve this problem, we propose two approaches. Firstly, we propose DSPT(Distributed Streaming P2P Tree) which takes advantage of combinational overlay multicasting. In DSPT, a peer doesn't fully rely on SP(Supplying Peer) to get the live stream, but it cooperates with its local ANR(Access Network Relay) to reduce delay and improve stream quality. When RP detects bandwidth drop in SP, it immediately switches the connection from SP to ANR and continues to receive stream without any packet loss. DSPT uses distributed P2P streaming technique to let the peer share the stream to the extent of its available bandwidth. This means, if RP can't receive the whole stream from SP due to lack of SP's uploading bandwidth, then it receives only partial stream from SP and the rest from the ANR. The proposed distributed P2P streaming improves P2P networking efficiency.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.10 no.1
• /
• pp.1388-1393
• /
• 1968

Higher yield in rice paddies is greatly dependent on adequately balanced and timely supply of water. A majority of rice paddy in Korea is generally irrigated by rainfall, but in many cases it has to be supplemented by artificial irrigation for optimum rice culture. Although the water requirement of rice plant is far higher than that of other crops, submerged condition of rice paddy is not necessarily required. The moisture requirement of rice plant varies with its growing stages, and it is possible to increase the irrigation efficiency through reduction of water loss due to percolation in rice paddies. An experiment was conducted on the effectiveness of economical use of water by different irrigation period and different method of cultivation. The experimental plots were set up by means of randomized block design with three duplications; (a) Alltime submerged (b) Economically controlled, and (c) Extremely controlled. Three different irrigation periods were (a) Initial stage (b) Inter-stage, and (c) last stage. The topsoil of the three plots were excavated to the depth of 30cm and then compacted with clay of 6 cm thickness. Thereafter, they were piled up with the excavated top soils, leveled and cored with clay of 6cm thickeness arround footpath in order to prevent leakage. The results obtained frome the experiments are as follows; (1) There is no difference among the three experiment plots in terms of physical and chemical contditions, soil properties, and other characteristics. (2) Colulm length and ear length are not affected by different irrigation methdos. (3) There is no difference in the mature rate and grain weight of rice for the three plots. (4) The control plot which was irrigated every three days shows an increased yield over the all the time submerged plot by 17 persent. (5) The clay lined plot whose water holding capacity was held days long, needs only to be irrigated every 7 days. (6) The clay lined plot showes an increased yield over the untreated plot; over all the time submerged plot by 18 percent, extremely controlled plot by 18 percent, and economically controled plot by 33 percent.

• Current Research on Agriculture and Life Sciences
• /
• v.8
• /
• pp.129-138
• /
• 1990

This study investigated the relationship between the cutflow of rural population and agricultural policy by using time series method. For the analytical tools, decomposition time series methods and regression technique were employed in computing seasonal fluctuation and cyclical fluctuation of population migration. Also, this study predicted farmhouse, rural population till the 2000's by means of the mathematical methods. The analytical forms employed in forecasting farmhouse, rural population were Exponential curve, Gompertz curve and Transcendental form. The major findings of this study were identified as follows: 1) Rural population and farmhouse population began to decrease from 1965 and hastily went down since 1975. Rural population which accounted for 36.4 percent, 35.6 percent of national population respectively in 1960 diminished about two times: 17.5 percent, 17.1 percent respectively. 2) The rapid decreasing of the rural population was caused because of the outflow of rural people to the urban regions. Of course, that was also caused from the natural decreases but the main reason was heavily affected more the former than the latter. In the outflowing course shaped from rural to the urban regions, rural people concentrated on such metropolis as Seoul, Pusan, Keanggi. But these trends were diminishing slowly. On the other hand, compared with that of the 1970's the migration to Keanggi was still increasing in the 1980's. That is, people altered the way of migration from the migration to Seoul, Pusan to the migration to the out-skirts of Seoul. 3) The seasonal fluctuation index of population migration has gone down since the June which the request of agricultural labor force increases and has turned to be greatly wanted in the March as result of decomposition time series method. As result of cyclical analysis, the cyclical patterns of migration have greatly 7 cycle. 4) As result of forecasting the rural and farmhouse population, rural and farmhouse population in the 2000 will be about 9,655(thousand/people) and 4,429(thousand/people) respectively. Thus, it is important to analyze the probloms that rural and farmhouse population will decrease or increase by the degree. But fairly defining the agricultural into a industry that supply the food, this problem - how much our nation need the rural and farmhouse population - is greatly significant too. Therefore, the basic problems of the agricultural including the outflows of rural people are the earning differentials between rural and urban regions. And we should regard the problems of the gap of relative incomes between rural and urban regions as the main task of the agricultural policy and treat the agricultural policy in the viewpoint of developing economic equilibrium than efficiency by using actively the natural resources of the rural regions.

• Journal of Intelligence and Information Systems
• /
• v.17 no.4
• /
• pp.213-226
• /
• 2011

In global supply chain, the scheduling problems of large products such as ships, airplanes, space shuttles, assembled constructions, and/or automobiles are complicated by nature. New scheduling systems are often developed in order to reduce inherent computational complexity. As a result, a problem can be decomposed into small sub-problems, problems that contain independently small scheduling systems integrating into the initial problem. As one of the authors experienced, DAS (Daewoo Shipbuilding Scheduling System) has adopted a two-layered hierarchical architecture. In the hierarchical architecture, individual scheduling systems composed of a high-level dock scheduler, DAS-ERECT and low-level assembly plant schedulers, DAS-PBS, DAS-3DS, DAS-NPS, and DAS-A7 try to search the best schedules under their own constraints. Moreover, the steep growth of communication technology and logistics enables it to introduce distributed multi-nation production plants by which different parts are produced by designated plants. Therefore vertical and lateral coordination among decomposed scheduling systems is necessary. No standard coordination mechanism of multiple scheduling systems exists, even though there are various scheduling systems existing in the area of scheduling research. Previous research regarding the coordination mechanism has mainly focused on external conversation without capacity model. Prior research has heavily focuses on agent-based coordination in the area of agent research. Yet, no scheduling domain has been developed. Previous research regarding the agent-based scheduling has paid its ample attention to internal coordination of scheduling process, a process that has not been efficient. In this study, we suggest a general framework for agent-based coordination of multiple scheduling systems in global supply chain. The purpose of this study was to design a standard coordination mechanism. To do so, we first define an individual scheduling agent responsible for their own plants and a meta-level coordination agent involved with each individual scheduling agent. We then suggest variables and values describing the individual scheduling agent and meta-level coordination agent. These variables and values are represented by Backus-Naur Form. Second, we suggest scheduling agent communication protocols for each scheduling agent topology classified into the system architectures, existence or nonexistence of coordinator, and directions of coordination. If there was a coordinating agent, an individual scheduling agent could communicate with another individual agent indirectly through the coordinator. On the other hand, if there was not any coordinating agent existing, an individual scheduling agent should communicate with another individual agent directly. To apply agent communication language specifically to the scheduling coordination domain, we had to additionally define an inner language, a language that suitably expresses scheduling coordination. A scheduling agent communication language is devised for the communication among agents independent of domain. We adopt three message layers which are ACL layer, scheduling coordination layer, and industry-specific layer. The ACL layer is a domain independent outer language layer. The scheduling coordination layer has terms necessary for scheduling coordination. The industry-specific layer expresses the industry specification. Third, in order to improve the efficiency of communication among scheduling agents and avoid possible infinite loops, we suggest a look-ahead load balancing model which supports to monitor participating agents and to analyze the status of the agents. To build the look-ahead load balancing model, the status of participating agents should be monitored. Most of all, the amount of sharing information should be considered. If complete information is collected, updating and maintenance cost of sharing information will be increasing although the frequency of communication will be decreasing. Therefore the level of detail and updating period of sharing information should be decided contingently. By means of this standard coordination mechanism, we can easily model coordination processes of multiple scheduling systems into supply chain. Finally, we apply this mechanism to shipbuilding domain and develop a prototype system which consists of a dock-scheduling agent, four assembly- plant-scheduling agents, and a meta-level coordination agent. A series of experiments using the real world data are used to empirically examine this mechanism. The results of this study show that the effect of agent-based platform on coordinated scheduling is evident in terms of the number of tardy jobs, tardiness, and makespan.

• The Journal of Korean Society for School & Community Health Education
• /
• v.1 no.1
• /
• pp.83-93
• /
• 2000

The purpose of this study were to suggest the method of sex education by designing and implementing multimedia program about sex education, to search the efficiency between a teaching using multimedia program and a teaching of traditional method. To put above aims into practice, these were required : 1. are there any differences in the alteration of sex attitude according to teaching methods. 2. are there any differences in the completion of sex knowledge according to teaching methods. 3. are there any differences in the alteration of sex attitude according to learning level and teaching methods. 4. are there any differences in the completion of sex knowledge according to learning level and teaching methods. 5. are there any differences in the alteration of sex attitude according to sex and teaching methods. 6. are there any differences in the completion of sex knowledge according to sex and teaching methods. To carry out a reseach for this purpose, the subjects for this study were 160 sixth grade students from 2 elementary schools in Pu-Chun, Kyung Ki. The tools for study were two kind of questionnaires: sex knowledge test, sex attitude test. Each test consists of 20 items. Collected data was analysed with t-test by means of SPSS program. The main results of this study are as follow: 1. The Alteration of sex attitude according to teaching methods. There was a significant difference among teaching methods(P<.001). a teaching using multimedia program was more efficient than a teaching of traditional method in the alteration of sex attitude. 2. The Completion of sex knowledge according to teaching methods. There was a significant difference among teaching methods(P<.001). a teaching using multimedia program was more efficient than a teaching of traditional method in the completion of sex knowledge. 3. The Alteration of sex attitude according to learning level and teaching methods. There was a significant difference among teaching methods in the superior class. a teaching using multimedia program was more efficient than a teaching of traditional method in the alteration of sex attitude(P<.001). However, there was not a significant difference among teaching methods in the inferior class(P>.05). 4. The Completion of sex knowledge according to learning level and teaching methods. There was a significant difference among teaching methods in the superior class. a teaching using multimedia program was more efficient than a teaching of traditional method in the completion of sex knowledge(P<.001). Also, there was a significant difference among teaching methods in the inferior class. a teaching using multimedia program was more efficient than a teaching of traditional method in the completion of sex knowledge(P<.001). 5. The Alteration of sex attitude according to sex and teaching methods. There was a significant difference among teaching methods in the man class. a teaching using multimedia program was more efficient than a teaching of traditional method in the alteration of sex attitude(P<.01). However, There was not a significant difference among teaching methods in the woman class(P>.05). 6. The Completion of sex knowledge according to sex and teaching methods. There was a significant difference among teaching methods in the man class. a teaching using multimedia program was more efficient than a teaching of traditional method in the completion of sex knowledge(P<.001). Also, there was a significant difference among teaching methods in the woman class. a teaching using multimedia program was more efficient than a teaching of traditional method in the completion of sex knowledge(P<.05).