• 콘크리트학회논문집
• /
• 제29권2호
• /
• pp.179-187
• /
• 2017

철근콘크리트 휨 부재의 최대철근비에 대한 설계 규정은 일반적으로 부재 파괴 시 철근이 항복하도록 하여 충분한 연성과 경제성을 보장 하도록 하고 있다. 콘크리트구조기준(2012)에서 최대철근비는 인장 철근의 순인장변형률 항으로 표현되고, 고강도 재료가 사용되는 경우 매우 높은 철근비를 나타낸다. 따라서 이는 콘크리트 타설시 시공성 확보에 어려움을 야기할 수 있다. 이에 반해, 도로교설계기준(한계상태설계)에서는 최대중립축 깊이비가 0.4가 되도록 최대철근비를 규정하고 있다. 이 결과로부터 시공성 및 연성을 확보할 수 있는 최대철근비에 대한 합리적인 모델을 제시하였다.

• 대한토목학회논문집
• /
• 제37권2호
• /
• pp.277-287
• /
• 2017

이 연구는 한계상태설계법을 기반으로 하는 도로교설계기준에 의해 철근콘크리트 휨부재 설계 시 적용하는 균형철근비와 최대 철근량에 대한 규정을 검토한 것이다. 현행 도로교설계기준(한계상태설계법)에서는 휨부재 철근량 산정의 기준이 되는 균형철근비에 대한 명시적 규정이 없고, 휨모멘트 재분배 효과를 반영한 최대 중립축 깊이 및 콘크리트 단면적의 0.04배로서 최대 철근량을 산정한다. 그런데, 최대 중립축 깊이 규정에 의하면 최대 철근량이 적게 산정되어 단면을 크게 하여야 하며, 콘크리트 단면적의 0.04배라는 한계값이 적용될 경우에는 인장 철근의 변형률이 항복 변형률의 2배 이하로 되어 충분한 연성거동을 보장할 수 없는 문제점이 있다. 이 연구에서는 연성거동을 확보할 수 있는 휨부재 설계를 위한 사용 철근량 산정의 기준이 되는 균형철근비를 극한한계상태 검증 규정 및 재료 특성과 콘크리트 기준압축강도에 따른 극한한계변형률을 도입하여 설계 실무에 적용할 수 있도록 간편한 식으로 유도하였다. 그리고, 설계된 휨부재가 충분한 연성이 확보되도록 인장철근의 최소허용변형률을 항복변형률의 2배로 가정하고 철근의 기준항복강도 및 콘크리트 기준압축강도에 상관없이 만족할 수 있도록 최대 중립축 깊이 비 보정계수를 도입하여 수정하고, 이로부터 최대철근비를 산정할 수 있도록 하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1988년도 춘계학술대회 논문집
• /
• pp.46-48
• /
• 1988

The effect of cold reduction ratio on magnetic properties of 45% Ni-Fe permalloy was studied. To know the relationship between the crystal orientation and the magnetic properties, the pole figure was measured by X-ray diffraction method. In the case of single rolled reduction, the coercive force decreased with cold reduction ratio monotonically, but the maximum permeability, induction and squreness increased drastically. In the case of double rolled reduction (total reduction ratio is 90%), the saturation and residual induction increased slightly with secondary reduction ratio, but the maximum permeability and the coercive force had the maximum and the minimum value at the 50/50% reduction ratio respectively. And strong {100} <100> pole was developed by increasing the cold reduction ratio.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.891-896
• /
• 2001

As composite materials, the addition of steel fiber in concrete significantly improves the engineering properties of structural members, notably shear strength and ductility, In this study, shear capacity evaluation method according to steel fiber contents was proposed from the literature surveys and member tests. For this, previously proposed five shear strength equation were examined and evaluated by maximum shear strength and shear capacity ratio. From the parametric study and regression analysis, following conclusion can be made; the maximum shear strength of steel fiber reinforced column will be estimated by relative shear capacity ratio.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2002년도 학술논문발표회
• /
• pp.69-74
• /
• 2002

The following results are achieved from a mortar flow test depending on stainless steel slag fineness, replacement ratio, and a research on material age compressive strength, strength activity index. 1. Flow is proportional to the stainless steel slag fineness within the limits of 4000~8000$\textrm{cm}^2$/g, but in the case of fineness 20000$\textrm{cm}^2$/g flow decreases at all conditions except the case of replacement ratio 10%. 2. As stainless steel slag replacement ratio increases, Mortar of flow somewhat decreases. 3. As stainless steel slag blends, compressive strength decreases, but in proportion to the increase of age, compressive strength increases. 4. As stainless steel slag replacement ratio, compressive strength decreases. 5. In the case of stainless steel slag fineness 6000$\textrm{cm}^2$/g and 20.000$\textrm{cm}^2$/g, compressive strength of revelation ratio has the maximum value when it's replacement ratio is 10%.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.162-167
• /
• 2000

The warm deep drawability in square cup drawing is investigated about a newly developed high-strength steel sheet with retained austenite which is transformed into martensite during forming. For this investigation, six steps of temperature ranges, from room temperature to $250^{\circ}C$, and five kinds of drawing ratio, from 2.2 to 2.6 were adopted. As a result the maximum drawing force and the maximum drawing depth were affected by the elevated temperatures, and the more stable thickness strain distribution was observed to the elevated temperatures. But blue shortness happened over $200^{\circ}C$. The FEM analysis using the LS-DYNA code is adopted to compare the experimental results with the analytical results for thickness strain distribution.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 가을 학술발표회 논문집
• /
• pp.284-292
• /
• 1995

This paper is on experimental study on the behavior of reinforced concrete columns subjected to longitudinal steel ratio To investigate the effects of concrete strength and longitedinal steel ratio on the behavior of reinforced concrete columns. a series of tests were carried out for thirty-six tied reinforced concrete columns with a 100mm square cross section and three slendemess ratio of 15, 30 and 50. And To study and illustrate the change of the ultimate loads and that of displacements, two different concrete strength of 180,26kfg/$\textrm{cm}^2$, 819,36kfg/$\textrm{cm}^2$ and five different longitudinal steel ratio of 0.5, 1.0, 4.0, 5.7 and 10.3% were used. The boundary conditions at the ends were both hinged and the end eccentricities (17mm) were equal and of the same sign. While the ultimate load capacity of high-strength concrete column was much increased when the columns were short, that was not when the columns were slender. The effect of longitudinal steel ratio on the increased of ultimate load of column was more evident for slender columns than for short ones and the ultimate of longitudinal steel ratio were more pronounced with increasing concrete strength. The more inserted the longitudinal steel, the more increased the ultimate load, but the superabundance of longitudinal steel ratio over the limitation of maximum steel ratio in ACI code was used, it was showed that the ultimate load was rather decreased.

• 콘크리트학회논문집
• /
• 제16권3호
• /
• pp.415-423
• /
• 2004

To improve the brittle column behavior during seismic excitation, benefits of using steel fiber reinforced concrete in columns were investigated. For experimental study, eight specimens were used to evaluate the shear enhancement effect. The variables in this study were amount of shear reinforcement ratio (i.e., 0.26, 0.21 $\%$) and steel fiber volume fraction (i.e., 0.0, 1.0, 1.5, 2.0$\%$). The test results indicated that the maximum enhancement of shear capacity was shown in $1.5\%$ steel fiber content. In addition, to predict the maximum shear strength, equations of ACI 318-99, AIJ MB, NZS 3101, Hirosawa and Priestley were reviewed. From the parametric and regression study, modified Priestely equation was proposed by adding steel fiber effect.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.593-598
• /
• 2002

Coupling adjacent steel frame using elastic dampers for control of response to low and moderate dynamic event is investigated in this paper. The complex modal superposition method is first used to determine dynamic characteristic, mainly modal damping ratio and modal frequency, of damper linked linear adjacent steel frame for fractical use. Dynamic response of steel frame linked by hydraulic-excitation method. This combined method can efectively and accurately determine dynamic response of non-clasically damped systems in the frequency domain. Parametric studties are finally performed to identify optimal parameters of elastic dampers for achieving the maximum modal damping ratio or the maximum response reduction of steel frame. It is demonstrated that using discrete elasatic dampers of proper parameters to link steel frame can reduce dynamic response significantly.

• Advances in concrete construction
• /
• 제8권2호
• /
• pp.139-144
• /
• 2019

In this study, the mechanical properties of reactive powder concrete (RPC) with a constant cement to silica fume ratio of 4 were investigated. In the experimental program, reactive powder concretes with steel fiber at different ratios were produced. Five productions using quartz sand with a maximum grain size of 0.6 mm were performed. A superplasticizer with a ratio of 3% of the cement was used for all productions. $40{\times}40{\times}160mm$ prismatic specimens were prepared and tested for flexural and compression. The specimens were exposed to two different curing conditions as autoclave and standard curing condition. Autoclave exposure was performed for 3 hours under a pressure of 2 MPa. It was observed that the compressive strength of concrete, along with the flexural strength exposed to autoclave was quite high compared to the strength of concretes subjected to standard curing. The results obtained indicated that the compressive strength, along with the flexural strength of autoclaved concrete increased as the amount of cement used increases. Approximately 15% increase in flexural strength was achieved with a 4% steel fiber addition. The maximum compressive strength that has been reached is over 210 MPa for reactive powder concrete for the same steel fiber ratio and with a cement content of $960kg/m^3$. The relationship between compressive strength and flexural strength of reactive powder concrete exposed to both curing conditions was also identified.