• Journal of Environmental Science International
• /
• v.6 no.6
• /
• pp.689-696
• /
• 1997

This paper discussed effect of the surface roughness and the hydrophobicity of support material on the microbial attachment In a rotating biological contactor. The by- drophoblclty of each support material was determined by the measurement of contact angle of water and the surface roughness was measured by the surface roughness In- strument. Microorganisms have well attached on the surface of more hydrophilic support material like Nylon6 than that of the hydrophobic support material like PE. When the relatively hydrophilic surface was roughen, the microbial attachment was increased but when the relatively hydrophobic surface was roughen, the attachment was slightly In- creased because the hydrophobicity of support material was Increased by roughening the hydrophobic surface. Although both variables, the surface hydrophobicity and the surface roughness, have Influenced the microbial attachment, the influence of the surface roughness overruled that of the surface hydrophobicity. Support material whose surfaces were roughened about 1mm, 6mm and 11mm were allowed for attached 3, 7 and 24hr, but the differences of maximum and minimum attachment of each material gave nearly constant values and similar trend with time.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.379-381
• /
• 2011

Direct numerical simulations (DNSs) of spatially developing turbulent boundary layers (TBLs) over two-dimensional (2-D) and rod and three-dimensional (3-D) cube rough walls were performed to investigate the effects of streamwise spacing on the properties of the TBL The 2-D and 3-D roughness were periodically arranged in the downstream direction with pitches of px/k=2, 3, 4, 6, 8 and 10 and for the cube, the spanwise spacing is fixed to pz/k=2 with staggered array, where px and pz are the streamwise and spanwise spacings of the roughness and k is the roughness height. Inspection of the Reynolds stresses showed that except for px/k=2 and 3 over the 2-D rough walls, the effects of the surface roughness extend to the outer layer over the 2-D and 3-D rough walls and the magnitude of the Reynolds shear stress in the outer layer is increased with proportion to px/k. However, such results are contrary to the trends of form drag, roughness junction and roughness length against px/k, which showed the maximum values at px/k=8 and 4 over the 2-D and 3-D rough walls respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.10
• /
• pp.1237-1243
• /
• 2014

The aim of the present paper is to analyze the friction and mass flow in a rough microchannel using Lattice Boltzmann Method (LBM). The LBM is a kinetic method based on the particle distribution function, so it can be fruitfully used to study the flow dependence on Knudsen number including slip velocity, pressure drop in rough microchannel. The surface roughness elements are taken to be considered as a series of circular shaped riblets throughout the channel with relative roughness height up to a maximum 10% of the channel height. The friction coefficients in terms of Poiseuille number (Pn), mass flow rate and the flow behaviors have been discussed in order to study the effect of surface roughness in the slip flow regime at Knudsen number (Kn), ranging from 0.01 to 0.10. It is seen that the friction factor and the flow behaviors in a rough microchannel strongly depend on the rarefaction effect and the relative roughness height. The friction factor in a rough microchannel is higher than that in smooth channel but the mass flow rate is lower than that of smooth channel. Moreover, it is seen that the friction factor increased with relative roughness height but decreased with increasing the Kundsen number (Kn) whereas the mass flow rate is decreased with increasing both of surface roughness height and Knudsen number.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.3
• /
• pp.141-148
• /
• 2006

An experimental study is presented for water droplet impingement on a steel surface in the process of heat treatment. The objective of the present work is to examine characteristic of evaporation cooling due to surface roughness and droplet diameter under conductive heat input condition. The surface temperatures varied from $80{\sim}155^{\circ}C$, surface roughness was from $R_a=0.12{\mu}m$ to $R_a=1.14{\mu}m$ and droplet diameter was from 2.4 mm to 3.0 mm. The results show that the total evaporation time is shorter for the larger surface roughness and the smaller droplet size, the time average heat flux has maximum value for the larger surface roughness and the smaller droplet size. The total evaporation time has not influence on the nuclear boiling region.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.6
• /
• pp.375-382
• /
• 2005

This paper presents the results of experimental investigation for the effect of heat conduction on the evaporation cooling of water droplet in the process of heat treatment. The experiments are mainly focused on the surface temperature, the surface roughness and the droplet diameter at aluminum. The range of surface temperature is from $80^{\circ}C$ to $140^{\circ}C$, surface roughness is from $R_a=0.18{\mu}m$ to $R_a=1.36{\mu}m$ and droplet diameter is from 2.4 mm to 3.0 mm. The results show that the total evaporation time is shorter for the larger surface roughness, the time averaged heat flux has maximum value for the larger surface roughness and exist the critical heat flux. The total evaporation time has a big influence on the evaporation region for the smaller droplet size, but the total evaporation time has not influence on the nuclear boiling region.

• Applied Science and Convergence Technology
• /
• v.25 no.6
• /
• pp.120-123
• /
• 2016

The rotor of a turbomolecular drag pump is generally made of an aluminum alloy. Its surface finish is affected by various processes that the rotor itself undergoes during the manufacturing phase. The impact of different surface finishes on the pumping performances of a turbomolecular pump has been mainly investigated by Sawada et al [1]. The present work aims to broaden the previous bibliographic study to the drag stages of a turbomolecular pump by testing the impact of different surface finishes on the compression ratio of the pump. Experimental tests have been made focusing on two processes: the corundum sandblasting and the glass microspheres shot-peening. Both the processes flatten and/or physically remove EDM melted spheres; in particular, blasted surfaces obtained by glass shot-peening are generally smoother than surfaces obtained by corundum sandblasting. In order to characterize the surface texture left by such processes, preliminary surface roughness measurements have been made on the drag rotor disks of several pumps. The experimental tests conducted on both sandblasted and shot-peened rotors confirms previous results obtained on the turbo stages by Sawada et al. [1], showing that the average roughness of the surface has an impact on the compression ratio of the pump; in particular, an increment in the surface roughness causes a corresponding increment in the compression ratio of the pump and vice versa. For the tested pumps, the higher surface roughness gives a factor of increment of about 2 on the measured hydrogen maximum compression ratio of the pump.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.101-105
• /
• 1992

Machined graphite/epoxy composite surfaces were studied by using SEM(Scanning Electron Microscopy). surface profilometry and its analysis to determine suitable surface describing parameters for machined unidirectional and laminate composite surface. The surface roughness and profile are found to be highly dependent on the fiber layup direction and the measurement direction. Machined unidirectional and 0.deg. 45 .deg. 90 .deg. plies in laminate composite surface profiles are found to be Gaussian in the direction of machining. Since there exist bare fibers without matrix smearing in 0 .deg. ply, higher surface roughness values were found in this orientation. It was possible to machine 90 .deg. and -45 .deg. plies due to the adjacent plies, which were holding those plies. It was found that the microgeometrical variations in terms of roughness parameters Ra without Dy (maximum Damage Depth) region and Dy are better descriptors of the machined laminate composite surface than commonly used roughness parameters Ra and Ra. The characteristics of surface profiles in laminate composite are well represented in CHD (Cumulative Height Distribution) plot and PPD (Percentage Probability Density) plot. Also, the power spectral density function is shown to be capable of identifying the wavelength distribution of the machining damage.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.993-998
• /
• 2004

In this paper, the effects of grinding conditions on the surface roughness of $ZrO_2$ ferrule applying to the optical fiber connector were investigated. The mesh number of grindstone, the grinding speed and the time schedule during grinding were regarded as main cutting parameters that have an effect on the surface roughness. And then, optimal combinations for chamfering grinding were obtained by using the Taguchi method. In addition, analytic values for maximum surface roughness ($R_{max}$) estimated by the theoretical equations which were derived from the formative model of surface roughness on the chamfering grinding were compared with those of the experiments.

• Transactions of Materials Processing
• /
• v.30 no.1
• /
• pp.27-34
• /
• 2021

In this study, response surface method (RSM) was used in modeling and multi-objective optimization of the parameters of AA5052-H32 in incremental sheet forming (ISF). The goals of optimization were the maximum forming angle, minimum thickness reduction, and minimum surface roughness, with varying values in response to changes in production process parameters, such as tool diameter, tool spindle speed, step depth, and tool feed rate. A Box-Behnken experimental design (BBD) was used to develop an RSM model for modeling the variations in the forming angle, thickness reduction, and surface roughness in response to variations in process parameters. Subsequently, the RSM model was used as the fitness function for multi-objective optimization of the ISF process based on experimental design. The results showed that RSM can be effectively used to control the forming angle, thickness reduction, and surface roughness.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.12
• /
• pp.149-156
• /
• 1995

This paper presents the surface profile of machined workpiece in face milling operation. The roughness model of feed direction is considered the cutting condition, the profile and run-out of inserts. For the dynamic model the cutting system can be modeled as avibratory system. The dynamic model of surface roughness is considered the relative displacements between tool and work- piece which can be obtained from the cutting system. These model can predict various surface roughnesses. i.e. maximum and arithmetic mean surface ruughnesses. Therefore, the developed model can be used for the monitoring of surface roughness.