• 한국소음진동공학회논문집
• /
• 제24권4호
• /
• pp.339-347
• /
• 2014

Floor impact sound in high-rise apartment building became one of social problems. A lot of civil complaints on floor impact sound occur continuously and the number of disputes between neighbors in small and aged apartment buildings is increasing. Interests on heavy-weight impact sound pressure level measurement and evaluation method is increased. Previous study reported that heavy-weight impact sound level was changed by the sound field condition of receiving reverberation chamber. In this study, heavy-weight impact sound pressure level change by the receiving sound field condition was measured in standard test facility and mock-up test room. These two experimental conditions were designed to simulate averaged living room of common apartment units. By the change of sound absorption power in receiving room, heavy-weight impact sound pressure level in most of frequency bands were changed in standard test facility and mock-up room. Normalized maximum sound pressure level regulated in ISO 16032 showed wider range of heavy/soft impact sound pressure level. Heavy/soft impact sound pressure level change was became smaller by the application of standardized maximum sound pressure level and ISO/CD 10140-3 Amd 2 method. In the case of standardized maximum sound pressure level, absolute sound pressure level changed. From these results, receiving sound field correction method regulated in ISO/CD 10140-3 Amd 2 is needed for the precision measurement and evaluation of heavy-weight impact sound.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.158-161
• /
• 1989

This paper describes the AR model of EMG signal during maximum voluntary contraction. By comparing the AR coefficients and the reflection coefficients of the AR model with the median frequency of power spectrum, it if proved that muscle fatigue can be measured by the AR and the reflection coefficients. In the estimation procedure of AR model parameter, the auto-correlation method is superior to the covariance method, and it is determined that the optimal order is six. As the muscle becomes fatigue, the median frequency of power spectrum is declined, and the AR coefficient [$a_1$ ] and the reflection coefficient [$k_1$ ] are also decreased. Therefore the muscle fatigue can be measured by the AR parameter.

• Transactions on Electrical and Electronic Materials
• /
• 제5권4호
• /
• pp.161-165
• /
• 2004

In order to get oxidizing power enough for growth of a superconductive thin film with oxide gas, concentrated ozone was used. As a method for concentrating ozone, a method for concentrating ozone by adsorbing ozone selectively into silica-gel beads is adopted, and this concentration is analyzed by the ultraviolet absorption method, the thermal decomposition method and the Q-mass analyzing method. Thermal decomposition method is most effective for measurement of a high concentration of ozone. Ozone as concentrated by the adsorption method got to have a concentration of 97 mol % at the maximum, and it was identified that the concentration of the ozone gas was stable for the time while a thin film was formed.

• Transactions on Electrical and Electronic Materials
• /
• 제16권1호
• /
• pp.16-19
• /
• 2015

A wearable sensing ECG T-shirt for ubiquitous vital signs sensing is proposed. The sensor system consists of a signal processing board and capacitive sensing electrodes which together enable measurement of an electrocardiogram (ECG) on the human chest with minimal discomfort. The capacitive sensing method was employed to prevent direct ECG measurement on the skin and also to provide maximum convenience to the user. Also, low power integrated circuits (ICs) and passive electrodes were employed in this research to reduce the power consumption of the entire system. Small flexible electrodes were placed into cotton pockets and affixed to the interior of a worn tight NIKE Pro combat T-shirt. Appropriate signal conditioning and processing were implemented to remove motion artifacts. The entire system was portable and consumed low power compared to conventional ECG devices. The ECG signal obtained from a 24 yr. old male was comparable to that of an ECG simulator.

• Nuclear Engineering and Technology
• /
• 제15권3호
• /
• pp.160-178
• /
• 1983

TRIGA Mark-III 원자로에서 핵연료봉의 내부 온도를 측정함으로써 노심의 출력분포를 유추하는 방법을 개발하였다. 핵연료 온도는 원자로의 안선 운전을 위하여 이미 장전되어 있는 계측 연료봉의 위치를 이동시켜 가면서 측정하였고 측정한 연료공의 수는 16개이다. 실험결과를 중성자확산이론에 의거한 노심계산의 결과와 비교한 바 최대편차는 12%, 표준편차는 5%였다. 핵연로 온도를 이용하여 연료봉의 출력밀도를 유추하는 방법은 기존의 다른 방법보다 훨씬 편리하면서 정확성을 유지할 수 있음이 판명되었다.

• 한국지능시스템학회논문지
• /
• 제20권6호
• /
• pp.852-857
• /
• 2010

최근 풍력발전 시스템은 가장 빨리 발전하고 있는 신재생 에너지원중 하나로 각광을 받고 있으며, 풍력발전 시스템의 주된 관심사는 어떻게 광범위한 풍속의 변화에서도 효율적으로 시스템을 동작시키는 가에 있다. 일반적으로 풍속은 풍력발전시스템의 동특성에 큰 영향을 미치는 요소이다. 따라서 많은 풍력발전 제어 알고리즘은 성능향상을 위해 풍속의 측정을 요구하게 된다. 그러나 불행히도 풍속계와 같은 센서에 의한 실효 풍속의 정확한 측정은 어려운 실정이며 따라서 제어 시스템의 동작을 위해 풍속은 여러 가지 기법을 통해 추정되고 있는 실정이다. 이에 본 연구에서는 신경망 학습을 통해 현재 풍속을 추정한 후 추정된 풍속을 이용하여 최대 전력점을 추종(MPPT)하는 방법을 제안하고자 하며, 제안된 기법의 유용성 검증을 위해 실제 제작된 실험환경에서의 적용실험을 수행하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(1)
• /
• pp.105-108
• /
• 2004

In this paper, the simple analog MPPT (Maximum Power Point Tracking) algorithm is proposed for the solar array of KOMPSAT (Korea Multi-Purpose Satellite). This method doesn't need any calculation of power by multiplication of voltage and current and a measurement of the solar array temperature. It is consist of only two sample and hold circuits, two comparators, a flip-flop, and an integrator. The proposed MPPT algorithm is verified by the simulation for the 100[W] solar array.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.998-1002
• /
• 1997

This study has been performed to predict beam absorption with analysis of temperature field by using a FEM in co /sab 2/ laser hardening and to invesrigate into some effects of power density and travel speed of laser beam on the microstructure and hardness of ductile cast iron treated by laser surface hardening technique. Optical micrograph has shown that large martensite and small amount of retained austenite appear in inside hardened zone. Hardness measurement has revealed that the range of maximum hardness value is Hv=415 .+-. 10. The power density increases and the travel speed decreases, the depth of hardened zone increases due to increase of input power density.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2018년도 전력전자학술대회
• /
• pp.126-128
• /
• 2018

Solar array simulator (SAS) is a special DC power supply that regulates the output voltage or current to emulate characteristics of photovoltaic (PV) panels. Especially, the control of SAS is a challenging task due to the nonlinearity in the output curve, which is dependent on irradiance as well as temperature and is determined by panel materials. Conventionally, both current-mode control and voltage-mode control should be alternated by partitioning the operating curve into multiple sections, which is not only for the measurement noise problem with the feedback sensing but also for the control stability issue near the maximum power point. However, the occurrence of transition among different controllers may deteriorate the overall performance. To eliminate the mode transitions, a novel single controller scheme has been introduced in this paper, where the reference operating projection technique enables simple, smooth and numerically stable control. Theoretical consideration on the loop stability issue is discussed and the performance is verified experimentally for the emulation of a PV panel data in view of stability and response speed.

• Journal of Magnetics
• /
• 제22권2호
• /
• pp.281-285
• /
• 2017

To suppress the wall slip effect and improve the yield stress measurement precision of magnetorheological fluid, measurement disks with different grooves are first manufactured. Then, the influence of groove characteristics on the yield stress of magnetorheological fluid is investigated by the method of experiments. Finally, the optimization wall grooves of measurement disks are obtained, and the yield stress of a self-prepared magnetorheological fluid is measured. Results indicate that the groove type and groove width have a slight influence on the shear yield stress, whereas the measured yield stress increases with enhanced groove density, and the optimized groove depth is 0.3 mm. The measured shear yield stress of self-prepared MR fluid can be improved by 18 % according to the optimized grooved disks, and the maximum yield stress can reach up to 65 kPa as the magnetic flux density is 0.5 T.