• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.388-388
• /
• 2016

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated with cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature $T_s$, and substrate dc bias $V_s$ as variables for efficient PEDOT:PSS/crystalline (c-)Si heterojunction solar cells (Fig. 1). The high-speed camera and differential mobility analysis characterizations revealed that average size and flux of PEDOT:PSS mist depend on f, solvent, and $V_s$. The size distribution of mist particles including EG/DI water cosolvent is also shown at three different $V_s$ of 0, 1.5, and 5 kV for a f of 3 MHz (Fig. 2). The size distribution of EG/DI water mist without PEDOT:PSS is also shown at the bottom. A peak maximum shifted from 300-350 to 20-30 nm with a narrow band width of ~150 nm for PEDOT:PSS solution, whose maximum number density increased significantly up to 8000/cc with increasing $V_s$. On the other hand, for EG/water cosolvent mist alone, the peak maximum was observed at a 72.3 nm with a number density of ~700/cc and a band width of ~160 nm and it decreased markedly with increasing $V_s$. These findings were not observed for PEDOT:PSS/EG/DI water mist. In addition, the Mie scattering image of PEDOT:PSS mist under white bias light was not observed at $V_s$ above 5 kV, because the average size of mist became smaller. These results imply that most of solvent is solvated in PEDOT:PSS molecule and/or solvent is vaporized. Thus, higher f and $V_s$ generate preferentially fine mist particle with a narrower band width. Film deposition occurred when $V_s$ was impressed on positive to a c-Si substrate at a Ts of $30-40^{\circ}C$, whereas no deposition of films occurred on negative, implying that negatively charged mist mainly provide the film deposition. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrate by adjusting $T_s$ and $V_s$. The adhesion of CMD PEDOT:PSS to c-Si enhanced by $V_s$ conspicuously compared to that of spin-coated film. The CMD PEDOT:PSS/c-Si solar cell devices on textured c-Si(100) exhibited a ${\eta}$ of 11.0% with the better uniformity of the solar cell parameters. Furthermore, ${\eta}$ increased to 12.5% with a $J_{sc}$ of $35.6mA/cm^2$, a $V_{oc}$ of 0.53 V, and a FF of 0.67 with an antireflection (AR) coating layer of 20-nm-thick CMD molybdenum oxide $MoO_x$ (n= 2.1) using negatively charged mist of 0.1 wt% 12 Molybdo (VI) phosphoric acid n-Hydrate) $H_3(PMo_{12}O_40){\cdot}nH_2O$ in methanol. CMD. These findings suggest that the CMD with negatively charged mist has a great potential for the uniform deposition of organic and inorganic on textured c-Si substrate by adjusting $T_s$ and $V_s$.

• Journal of Aquaculture
• /
• v.10 no.4
• /
• pp.449-456
• /
• 1997

This study was concuted to determine the optimal conditions for raising the freshwater rotifer, Brachinus calyciflorus. The authors presented some biological informatin obtained from incubation experiment under the various controlled temperatures. Lorica size of the rotifer was divided into two groups : the length and the width for the S-type was $141.0\pm16.7\mu m$($110.1-182.5\;\mu m, n=44$)and $107.0\pm20.3\mu m\;(75.3-152.3\mu m, n=44)$, and those for the L-type was $262.8\pm15.2\mu m\;(234.4-288.6\mu m,\;n=20)\;and\;182.6\pm13.4\mu m (159.8-207.0\mu m,\;n=20$), respectively. The number of eggs being attached on the female varied from 1 to 11 at various culture conditions. Egg type was divided into two groups, large and small. Large and small egg was measured in its major axis as 85a.7-107.8$\mu$m and 55.1-65.2$\mu$m for S-type, and 104.9-121.8 $\mu$m and 62.8-89.1$\mu$m for L-type respectively. The maximum density was reached at 4th day after incubation. The density was 583.9 rotifers/$m\ell$ for $25^{\circ}C$-experimental. group and 421.3 rotifers/$m\ell$ for $22^{\circ}C$-experimental. group respectively. In the case of $28^{\circ}C$-experimental. group, it suddenly decreased into 4.7 rotifers/$m\ell$ at 1st day after incubations and did not recover to its initial density. The maximum rate of increase of populatin per day was reached 0.802 for $22^{\circ}C$-experimental. group at day 2 and fluctuated thereafter. For $25^{\circ}C$-experimental. group it increased to 0.964 at day 3 of incubation and then declined. And the egg ratio of female was reached the maximum of 0.614 for 22$^{\circ}C$- at 3rd day and 0.772 for $25^{\circ}C$-experimental. group at 4th day of incubation.

• Composites Research
• /
• v.31 no.2
• /
• pp.43-50
• /
• 2018

The effects of deposition temperature on chemical vapor deposited silicon carbide (CVD-SiC) were studied to obtain high deposition rates and excellent bending strength characteristics. Silicon carbide prepared at $1250{\sim}1400^{\circ}C$ using methyltrichlorosilane(MTS : $CH_3SiCl_3$) by hot-wall CVD showed deposition rates of $95.7{\sim}117.2{\mu}m/hr$. The rate-limiting reaction showed the surface reaction at less than $1300^{\circ}C$, and the mass transfer dominant region at higher temperature. The activation energies calculated by Arrhenius plot were 11.26 kcal/mole and 4.47 kcal/mole, respectively. The surface morphology by the deposition temperature changed from $1250^{\circ}C$ pebble to $1300^{\circ}C$ facet structure and multi-facet structure at above $1350^{\circ}C$. The cross sectional microstructures were columnar at below $1300^{\circ}C$ and isometric at above $1350^{\circ}C$. The crystal phases were all identified as ${\beta}$-SiC, but (220) peak was observed from $1300^{\circ}C$ or higher at $1250^{\circ}C$ (111) and completely changed to (220) at $1400^{\circ}C$. The bending strength showed the maximum value at $1350^{\circ}C$ as densification increased at high temperatures and the microstructure changed from columnar to isometric. On the other hand, at $1400^{\circ}C$, the increasing of grain size and the direction of crystal growth were completely changed from (111) to (220), which is the closest packing face, so the bending strength value seems to have decreased.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.17 no.1
• /
• pp.57-71
• /
• 2015

This study was conducted to develop the fertigation system with a peristaltic hose pump and brushless DC motor. The fertigation system was consisted of sensor, main controller, motor control unit, peristaltic pump, water supply pump, control panel, and filter. The peristaltic pump discharges liquid by squeezing the tube with rollers. Rollers attached to the external circumference of the rotor compresses the flexible tube. The fluid is contained within a flexible tube fitted inside a circular pump casing. The developed fertigation system has no mixing tank but instead injects directly a concentrated nutrient solution into a water supply pipe. The revolution speed of the peristaltic pump is controlled by PWM (Pulse width modulation) method. When the revolution speed of the peristaltic pump was 300rpm, the flow rate of the 3.2, 4.8, 6.3mm diameter tube was 202, 530, 857mL/min, respectively. As increasing revolution speed, the flow rate of the peristaltic pump linearly increased. As the inner diameter of a tube larger, a slope of graph is more steep. Flow rate of three roller was more than that of four roller. Flow rate of a norprene tube with good restoring force was more than that of a pharmed tube. As EC sensor probe was installed in direct piping in comparison with bypass piping showed good performance. After starting the system, it took 16~17 seconds to stabilize EC. The maximum value of EC was 1.44~1.7dS/m at a setting value of 1.4dS/m. The developed fertigation system showed ±0.06dS/m deviation from the setting value of EC. In field test, Cucumber plants generally showed good growth. From these findings, this fertigation system can be appropriately suitable for fertigation culture for crops.

• Korean Journal of Remote Sensing
• /
• v.32 no.3
• /
• pp.307-321
• /
• 2016

Planetary Boundary Layer Height (PBLH) is a major input parameter for weather forecasting and atmosphere diffusion models. In order to estimate the sub-grid scale variability of PBLH, we need to monitor PBLH data with high spatio-temporal resolution. Accordingly, we introduce a LIdar observation VEhicle (LIVE), and analyze PBLH derived from the lidar loaded in LIVE. PBLH estimated from LIVE shows high correlations with those estimated from both WRF model ($R^2=0.68$) and radiosonde ($R^2=0.72$). However, PBLH from lidar tend to be overestimated in comparison with those from both WRF and radiosonde because lidar appears to detect height of Residual Layer (RL) as PBLH which is overall below near the overlap height (< 300 m). PBLH from lidar with 10 min time resolution shows typical diurnal variation since it grows up after sunrise and reaches the maximum after 2 hours of sun culmination. The average growth rate of PBLH during the analysis period (2014/06/26 ~ 30) is 1.79 (-2.9 ~ 5.7) m $min^{-1}$. In addition, the lidar signal measured from moving LIVE shows that there is very low noise in comparison with that from the stationary observation. The PBLH from LIVE is 1065 m, similar to the value (1150 m) derived from the radiosonde launched at Sokcho. This study suggests that LIVE can observe continuous and reliable PBLH with high resolution in both stationary and mobile systems.

• Journal of Aquaculture
• /
• v.18 no.3
• /
• pp.135-141
• /
• 2005

A 16-week feeding trial was conducted to estimate the optimum dietary protein to energy ratio (P/E ratio, mg/kcal) in juvenile Japanese eel, Anguilla japonica. Six experimental diets were formulated with three energy levels and two protein levels at each energy level. Three energy levels of 3800, 4150 and 4500 kcal per kg diets were included at 45 and 50% crude protein (CP) levels, respectively $(_{120}P_{45},\;_{110}P_{45},\;_{100}P_{45},\;_{130}P_{50},\;_{120}P_{50},\;and\;_{110}P_{50})$. After four weeks of the conditioning period, fish initially averaging $15.0{\pm}3g\;(means{\pm}SD)$ were randomly distributed into each tank as groups of 20 fish. Each diet was fed to fish in three randomly selected tanks at a rate of $2{\sim}3%$ wet body weight per day in the recirculated system. Weight gain (WG) and specific growth rate of fish fed diet $_{100}P_{45}$ were significantly higher (P<0.05) than those of fish fed the other diets. WG of fish fed diet $_{120}P_{50}$ was also significantly higher than those of fish fed diets $_{130}P_{50}$ and $_{110}P_{50}$. Feed efficiency ratio of fish fed diets $_{100}P_{45}$ and $_{110}P_{45}$ were significantly higher (P<0.05) than those of fish fed other diets. These results suggest that the optimum P/E ratio may be 100 mg/kcal with 45% protein diets, and 120 mg/Kcal 50% protein diets for the maximum growth of juvenile Japanese eel under the experimental condition.

• Horticultural Science & Technology
• /
• v.32 no.4
• /
• pp.427-433
• /
• 2014

Trellising is an important cultural practice that affects grape quality and yield. Some grape cultivars require different trellising under different climate and soil conditions. To find suitable trellis conditions for grape cultivar 'Cheongsoo', we measured growth and fruit characteristics with three different trellis systems: curtain, Geneva double curtain (GDC), and modified T. The maximum light exposure of clusters in the curtain, GDC, modified T trellis systems was 670, 1,654, and $1,649{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, respectively. However, there was no difference in air temperature among the three trellis systems. Net $CO_2$ assimilation rate at $1,500{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ light intensity was 13.4, 13.7, and $8.7{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ in curtain, GDC, and modified T trellis systems, respectively. Trunk cross section area (TCSA) and bud burst rate were not significantly different among the three systems. Shoot number was 31.3, 47.0, and 37.0 in curtain, GDC, and modified T trellis systems, respectively. The shoot length was higher (243.9 cm) in the modified T trellis system than in the single curtain (171.1 cm) and GDC (151.5 cm) systems. Interior leaf number and leaf layer number were higher in the GDC system, in which there are two primary branches, in comparison to the modified T and curtain systems, which utilize one primary branch. Primary leaf area and lateral leaf area were significantly higher in the modified T trellis system in comparison to the GDC system. Berry weight, length and diameter, and total soluble solids were not significantly different among the three trellis systems. However, cluster weight and cluster number per tree were significantly higher in GDC. Titratable acidity was significantly lower in GDC. Collectively, our data suggest that the GDC trellis system is preferable for grape 'Cheongsoo' to maintain fruit quality and quantity in Korea.

• Journal of Bio-Environment Control
• /
• v.29 no.4
• /
• pp.373-380
• /
• 2020

This study was conducted to investigate the effect of elevated temperatures on the growth and physiological responses of peach 'Mihong' (Prunus persica). We simulated three different temperature conditions in the sunlight phytotron rooms from April 25 to July 5, 2019; Control (average temperature in normal years in Jeonju city), +3.4℃ treatment (expecting temperature in mid-21st century), +5.7℃ treatment (expecting temperature in late 21st century). The shoot numbers and lengths were increased while the temperature was increased, but the leaf areas were not statistically different. The harvest dates were July 1, June 24 and 21 at the control, +3.4℃, and +5.7℃, respectively. The fruit weights were increased at +3.4℃ but decreased at +5.7℃ compared to the control. The tree yield was the highest in the +3.4℃ (2,898g), followed by the control (2,746g) and the +5.7℃ (2,404g). These are related to the result that the average of maximum photosynthesis rate at 3.4℃ (14.93μmol·CO₂·m^-2·s^-1) was higher than those at the control (13.79μmol·CO₂·m^-2·s^-1) and +5.7℃ (13.20μmol·CO₂·m^-2·s^-1) from mid-May to early June, the fruit growing season. Also, the stomatal densities were higher at the +3.4℃ (229ea/㎟), compared to the control (181ea/㎟). The rate of floral bud differentiation affecting the yield in the following year was the lowest at the +5.7℃. These results suggest that a temperature elevated to 3.4℃ in the future may give a positive effect on the yield and quality of peach 'Mihong' while a temperature elevated above 5.7℃ may affect negatively.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.19 no.1
• /
• pp.4279-4295
• /
• 1977

Two types of model were established in order to product the soil moisture content by which information on irrigation could be obtained. Model-I was to represent the soil moisture depletion and was established based on the concept of water balance in a given soil profile. Model-II was a mathematical model derived from the analysis of soil moisture variation curves which were drawn from the observed data. In establishing the Model-I, the method and procedure to estimate parameters for the determination of the variables such as evapotranspirations, effective rainfalls, and drainage amounts were discussed. Empirical equations representing soil moisture variation curves were derived from the observed data as the Model-II. The procedure for forecasting timing and amounts of irrigation under the given soil moisture content was discussed. The established models were checked by comparing the observed data with those predicted by the model. Obtained results are summarized as follows: 1. As a water balance model of a given soil profile, the soil moisture depletion D, could be represented as the equation(2). 2. Among the various empirical formulae for potential evapotranspiration (Etp), Penman's formula was best fit to the data observed with the evaporation pans and tanks in Suweon area. High degree of positive correlation between Penman's predicted data and observed data with a large evaporation pan was confirmed. and the regression enquation was Y=0.7436X+17.2918, where Y represents evaporation rate from large evaporation pan, in mm/10days, and X represents potential evapotranspiration rate estimated by use of Penman's formula. 3. Evapotranspiration, Et, could be estimated from the potential evapotranspiration, Etp, by introducing the consumptive use coefficient, Kc, which was repre sensed by the following relationship: Kc=Kco$.$Ka＋Ks‥‥‥(Eq. 6) where Kco : crop coefficient Ka : coefficient depending on the soil moisture content Ks : correction coefficient a. Crop coefficient. Kco. Crop coefficients of barley, bean, and wheat for each growth stage were found to be dependent on the crop. b. Coefficient depending on the soil moisture content, Ka. The values of Ka for clay loam, sandy loam, and loamy sand revealed a similar tendency to those of Pierce type. c. Correction coefficent, Ks. Following relationships were established to estimate Ks values: Ks=Kc-Kco$.$Ka, where Ks=0 if Kc,=Kco$.$K0$\geq$1.0, otherwise Ks=1-Kco$.$Ka 4. Effective rainfall, Re, was estimated by using following relationships : Re=D, if R-D$\geq$0, otherwise, Re=R 5. The difference between rainfall, R, and the soil moisture depletion D, was taken as drainage amount, Wd. {{{{D= SUM from { {i }=1} to n (Et-Re-I+Wd)}}}} if Wd=0, otherwise, {{{{D= SUM from { {i }=tf} to n (Et-Re-I+Wd)}}}} where tf=2∼3 days. 6. The curves and their corresponding empirical equations for the variation of soil moisture depending on the soil types, soil depths are shown on Fig. 8 (a,b.c,d). The general mathematical model on soil moisture variation depending on seasons, weather, and soil types were as follow: {{{{SMC= SUM ( { C}_{i }Exp( { - lambda }_{i } { t}_{i } )+ { Re}_{i } - { Excess}_{i } )}}}} where SMC : soil moisture content C : constant depending on an initial soil moisture content $\lambda$ : constant depending on season t : time Re : effective rainfall Excess : drainage and excess soil moisture other than drainage. The values of $\lambda$ are shown on Table 1. 7. The timing and amount of irrigation could be predicted by the equation (9-a) and (9-b,c), respectively. 8. Under the given conditions, the model for scheduling irrigation was completed. Fig. 9 show computer flow charts of the model. a. To estimate a potential evapotranspiration, Penman's equation was used if a complete observed meteorological data were available, and Jensen-Haise's equation was used if a forecasted meteorological data were available, However none of the observed or forecasted data were available, the equation (15) was used. b. As an input time data, a crop carlender was used, which was made based on the time when the growth stage of the crop shows it's maximum effective leaf coverage. 9. For the purpose of validation of the models, observed data of soil moiture content under various conditions from May, 1975 to July, 1975 were compared to the data predicted by Model-I and Model-II. Model-I shows the relative error of 4.6 to 14.3 percent which is an acceptable range of error in view of engineering purpose. Model-II shows 3 to 16.7 percent of relative error which is a little larger than the one from the Model-I. 10. Comparing two models, the followings are concluded: Model-I established on the theoretical background can predict with a satisfiable reliability far practical use provided that forecasted meteorological data are available. On the other hand, Model-II was superior to Model-I in it's simplicity, but it needs long period and wide scope of observed data to predict acceptable soil moisture content. Further studies are needed on the Model-II to make it acceptable in practical use.

• Applied Biological Chemistry
• /
• v.9
• /
• pp.41-57
• /
• 1968

Changes of acids (total, titratable and combined form) and sugars (total, reducing and non-reducing) in the edible part and the rind of 17 varieties the in growing and ripening period were investigated. The results were summarized as follows. 1) The percentage of rind was notably decreased in growing period and slightly in the ripening period- It may suggest that the rates of translocation of metabolite from leaves to each part of fruit are different with growth phase. 2) The heavier the weight of fruit, the higher the percentage of rind was and the varieties having over 200 g per fruit showed the value over 30 in the rind percentage and over 15 in the number seeds per fruit. 3) Total acid contents in the rind were highest at the maximum grow th of fruit except in Citrus grandis having tie lowest value (below 20 me/100 g F.W). of total acid at maximum point in which total acid content is steadily increase. 4) Total acid and titratable acid in the edible part and total acid and combined acid in whole fruit life showed 0.933 and 0.970 of correlation coefficient significant at 1% level respectively, and most acid in the edible part was titratable acid(73%) whereas acid in the rind consists mostly of combined acid. 5) The content of combined acid in the ripening period increased in the edible part and decreased in the rind. It may be contributed to translocation of some cations from the rind to the edible part. 6) The grouping criteria on citrus fruit were applicable on melon, watermelon and tomatoes. 7) The contents of total sugar and non-reducing sugar in the edible part were continuously increased whereas the content of reducing sugar were decreased in certain varieties, notablly in citrus natsudaidai. The correlation coefficient between total sugar and reducing sugar in the edible part with ripening decreased as $0.849^{**},\;0.732^{**}.\;0.583^*$. ( $^{**}$: significant at 1% level and $^{*}:$: at 5%) 8) 61% of total sugar in the edible part was non-reducing sugar whereas 88% of total sugar in the rind was reducing form at the end of ripening and the correlation coefficient between total and non-reducing sugar in the edible part was 0.861 end total and reducing sugar in the rind was 0.972, both significant at 1% level. 9) Varieties having the percentage of the rind below 36 showed higher value than I in the ratio of total sugar in the edible part to one in the rind. It may suggest that there exists any intimate relation between relative sugar content and growth rate of fruit parts. 10) Citrus unshiu in Guje island showed lower values in the content of acid and sugar, and the rind percentage but higher sweetness index (the ratio of total sugar to titratable acid) comparing with the same variety in Jeiu.