• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.8 s.99
• /
• pp.815-824
• /
• 2005

In this paper, we proposed a new DGS(Defected Ground Structure) Doherty amplifier for IMT-2000 band. Originally, active load-pull analysis of a Doherty amplifier assumes ideal harmonic termination condition. However, there have been no papers considering this ideal harmonic termination condition. We obtained excellent improvements of efficiency, gain, maximum output power as well as superior size reduction of a Doherly amplifier by satisfying the overlooked assumption of ideal harmonic termination through the adaptation of DGS at the output transmission line of carrier and peaking amplifier that is essential for Doherty operation. The amount of both the 2nd and the 3rd harmonic rejection of the proposed DGS Doherty amplifier over the conventional one are 44.92 dB and over 23.77 dB, respectively. The acquired improvement in Pl dB, gain, drain efficiency, and ACPR to WCDMA 1FA signal were 0.42 dB, 0.33 dB, $6.4\%$ and 5.4 dBc, respectively. Moreover, electrical length of $90{\circ}$ is reduced at each of the DGS carrier amplifier path and DGS peaking amplifier path, therefore the whole amplifier circuit size is considerably reduced.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.200-207
• /
• 2009

This paper presents a compact, low insertion loss, sharp rejection and wide band microstrip band pass filter that is composed rectangular loop resonator and Step-Impedance-Open-Stub(SIOS). The SIOS can be reduce length about 30 % more than general 0.25 $\lambda$ open stub. And the stub can the advantage of tuning impedance magnitude. In order to demonstrate agrement of this paper prove, the optimized wide band pass filters are realized and experimented. A transmission line model used to calculate the frequency response of the new filters shows good agreement with measurements. The filter has 3 dB fractional bandwidth of 51.75 %(3.206 GHz), an insertion loss of better than 0.44 dB from 4.587 GHz to 7.793 GHz, and two rejection of greater than 30 dB within 221 MHz($4.326{\sim}4.587\;GHz$) at low frequency band, 181 MHz($7.739{\sim}7.954\;GHz$) at high frequency band. Maximum rejection characteristics of the filter are -61.8 dB at low frequency and -76.3 dB at high frequency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.5B
• /
• pp.502-510
• /
• 2011

In this research, a wireless movable systems is introduced that is applicable for real-world clinical examination in order to resolve the inconvenience of wired motion analysis system which uses markers by measuring more accurately the angle of the 3D motion. The system is composed of bluetooth data transmission and 6 DOF inertial measurement system that is composed of 3-axis acceleration and 3-axis gyroscope. The samples were collected from 10 feet of 5 young children who were confirmed as patients having flat feet and achilles tendonitis by podiatric expert in pediatrics, and the validity of the system was evaluated by comparison with the opinion by the expert using the EMG data and the data measured by the developed system. ROM of ankle was measured by the difference between the maximum and the minimum peaks of 3-axis values (pitch, roll and yaw) measured at lateral malleolus bone, and based on this measured value, the eversion rate became relatively higher as flat feet state become worse, which is equivalent to the opinion from the podiatric experts. It was shown that there is a relation between the certain muscle activities and the abnormal motion of foot caused by disease.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.2
• /
• pp.150-156
• /
• 2001

To explore the feasibility of recycled paper mulching in spring-grown potato the changes of soil environments and the growth and yield of potato under non-mulched control and three mulching treatments of recycled paper (RPM), transparent polyethylene film (TPFM), and black polyethylene film (BPFM) were examined over two spring seasons in 1998 and 1999 at Suwon, Korea. The mulching materials were a recycled mulch paper with 110 g/$m^2$ and a thickness of 0.1mm, which was manufactured from old corrugated containers for this experiment and the commercial polyethylene films with a thickness of 0.01mm. RPM lowered the average soil temperature at 5-cm depth during the potato growing period by 03$^{\circ}C$ compared with the control, whereas TPFM and BPFM raised it by 2.$0^{\circ}C$, and 1.8$^{\circ}C$, respectively. On a sunny day during sprout emergence, RPM reduced the maximum soil temperature by about 5$^{\circ}C$, while TPFM and BPFM enhanced it by about 11$^{\circ}C$ and 6.$0^{\circ}C$, respectively. The temperature difference between the control and the mulching treatments decreased with the development of canopy. All the mulching treatments had an advantage in preserving the soil moisture over the control. RPM and BPFM resulted in the effective control of weed by obstructing light transmission onto soil surface, but TPFM had no control effect of weed. Sprout emergence started two to three days earlier in TPFM and BPFM, but one day later in RPM than in the control due to the altered soil temperature by the mulching treatments. However, the final percentage of emergence was notably lower in TPFM than that in the control because of too high soil temperature during daytime, but was not different among the control, RPM, and BPFM. During the early stage of potato growth, the shoot and root growth under RPM was lower compared with the control, but afterwards, RPM outpaced the control. In 1998 experiment, the tuber yield under RPM and BPFM were significantly higher than those of the control and TPFM. In 1999 experiment, there was no significant difference in tuber yield between RPM and the control.

• Cartoon and Animation Studies
• /
• s.14
• /
• pp.151-164
• /
• 2008

Cross platform game has brought about the expansion of game market, which results in technology innovation overcoming the limit of game consumption. The new model integrates both off and online game services. Gamers can now enjoy game service regardless of age, time, and space. If the technology evolution model of digital contents like cross-platform game engine can provide contents for several platform at the same time, the interactive service can be utilized into maximum level. It is also necessary to allocate, switch data as well as to innovate the transmission technology of data according to each platform. Providing the same contents for several platform as many as possible can be the most suitable strategy to enhance the efficiency and profits. However if the interactive service can be accomplished completely, the development of data switching technology and distribution should be made. To be a leader in the next digital contents market, one should develop the network engine technology which can embody the optimization of consumption in the interactive network service.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.10
• /
• pp.90-99
• /
• 2009

In this paper, we proposed the new class-E frequency multiplier design that include the highest efficient characteristics. The proposed frequency multiplier is designed for 5.8[GHz] output using the frequency multiplier about 2.9[GHz] input signal. And studying in this paper is for the design and the implementation of the class E frequency multiplier. For the result, the maximum highest efficient characteristics 32[%] which is with output power 24.5[dBm] and 8.5[dB], is shown with frequency multiplier for the 2.9/5.8[GHz] class E. And we applied the linear method to the implemented class E frequency multiplier. As a result, the output spectrum for the linear is upgrade to 12[dB], 12[dB], 13[dB] of the ACPR characteristics on the +11[MHz], +20[MHz], +30[MHz] offset frequency in the center frequency. The result is satisfied with the 3.83[%] of the lineared EVM for the 64-QAM modulated method with the 54[Mbps] transmission velocity. In this paper, we show that the good compensation result of the linearity and the efficiency through the digital pre-linear method of the distortion with the frequency multiplier. Therefore, we suggested the frequency multiplier method are applying to WLAN, cellular, PCS, WCDMA, and etc.

• Journal of KIISE:Information Networking
• /
• v.37 no.4
• /
• pp.272-283
• /
• 2010

Wireless Mesh Networks (WMNs) have gained a lot of attention recently. Based on the characteristic of WMNs as a highly connected wireless infrastructure, many efforts from research organizations are made in order to improve the performance of the flow throughput in WMNs. Therefore, it is very critical issue to establish efficient routing paths for multiple concurrent ongoing flows. In this paper, we propose a general modeling methodology to analyze the end-to-end throughput of multiple concurrent flows by analytical calculation taking into account the carrier sensing behaviors, interference and the IEEE 802.11 Distributed Coordination Function mechanism. After the comparison of the average service time for each successful transmission at each node, we analyze the bottlenecks of flows, and hence obtain the maximum end-to-end throughput of them. By using our proposed model, it is possible to predicate the throughput of several candidate routing paths for multiple concurrent ongoing data flows, so we can select the most efficient route that can achieve the highest throughput. We carry out simulations with various traffic patterns of multiple flows in WMNs to validate our modeling and our efficient route selection mechanism.

• Journal of Korea Multimedia Society
• /
• v.15 no.6
• /
• pp.805-813
• /
• 2012

In this paper, we have designed and developed a middleware for an effectively approaching database to the existed brain disease clinical research system. The brain disease clinical research system was consisted of two parts i.e., a register and an analyzer. Since the register collects the registration data the analyzer yields a statistical data which based on the diverse variables. The middleware has designed to database management and a large data query processing of clients. By separating the function of each feature as a module, the module which was weakened connectivity between functionalities has been implemented the re-use module. And image data module used a new compression method from image to text for an effective management and storage in database. We tested the middleware system using 700 actual clinical medical data. As a result, the total data transmission time was improved maximum 115 times faster than the existing one. Through the improved module structures, it is possible to provide a robust and reliable system operation and enhanced security functionality. In the future, these middleware importances should be increased to the large medical database constructions.

• The KIPS Transactions:PartC
• /
• v.12C no.1 s.97
• /
• pp.121-128
• /
• 2005

Tho existing TCP(Transmission Control Protocol) is known to be unsuitable for a network with the characteristics of high RDP(Bandwidth-Delay Product) because of the fixed small or large buffer size at the TCP sender and receiver. Thus, some trial cases of adjusting the buffer sizes automatically with respect to network condition have been proposed to improve the end-to-end TCP throughput. ATBT(Automatic TCP fluffer Tuning) attempts to assure the buffer size of TCP sender according to its current congestion window size but the ATBT assumes that the buffer size of TCP receiver is maximum value that operating system defines. In DRS(Dynamic Right Sizing), by estimating the TCP arrival data of two times the amount TCP data received previously, the TCP receiver simply reserves the buffer size for the next arrival, accordingly. However, we do not need to reserve exactly two times of buffer size because of the possibility of TCP segment loss. We propose an efficient TCP buffer tuning technique(called TBT-PLR: TCP buffer tuning algorithm based on packet loss ratio) since we adopt the ATBT mechanism and the TBT-PLR mechanism for the TCP sender and the TCP receiver, respectively. For the purpose of testing the actual TCP performance, we implemented our TBT-PLR by modifying the linux kernel version 2.4.18 and evaluated the TCP performance by comparing TBT-PLR with the TCP schemes of the fixed buffer size. As a result, more balanced usage among TCP connections was obtained.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.436-441
• /
• 1998

$Pt/SrTiO_3/Pb_x(Zr_{0.52}, Ti_{0.48})O_3/SrTiO_3/Si$ structure was prepared by rf-magnetron sputtering method for use in nondestructive read out ferroelectric RAM(NDRO-FEAM). PBx(Zr_{0.52}Ti_{0.48})O_3}$(PZT) and $SrTiO_3$(STO) films were deposited respectively at the temperatures of $300^{\circ}C and 500^{\circ}C$on p-Si(100) substrate. The role of the STO film as a buffer layer between the PZT film and the Si substrate was studied using X-ray diffraction (XRD), Auger electron spectroscopy (ASE), and scanning electron microscope(SEM). Structural analysis on the interfaces was carried out using a cross sectional transmission electron microscope(TEM). For PZT/Si structure, mostly Pb deficient pyrochlore phase was formed due to the serious diffusion of Pb into the Si substrate. On the other hand, for STO/PZT/STO/Si structure, the PZT film had perovskite phase and larger grain size with a little Pb interdiffusion. the interfaces of the PZT and the STO film, of the STO film and the interface layer and $SiO_2$, and of the $SiO_2$ and the Si substate had a good flatness. Across sectional TEM image showed the existence of an amorphous layer and $SiO_2$ with 7nm thickness between the STO film and the Si substrate. The electrical properties of MIFIS structure was characterized by C-V and I-V measurements. By 1MHz C-V characteristics Pt/STO(25nm)/PZT(160nm)/STO(25nm)/Si structure, memory window was about 1.2 V for and applied voltage of 5 V. Memory window increased by increasing the applied voltage and maximum voltage of memory window was 2 V for V applied. Memory window decreased by decreasing PZT film thickness to 110nm. Typical leakage current was abour $10{-8}$ A/cm for an applied voltage of 5 V.