• Journal of the Korean Chemical Society
• /
• v.39 no.3
• /
• pp.204-212
• /
• 1995

The graphite furnace atomic absorption spectrophotometric determination of trace lead in water samples was studied using matrix modifiers. In order to modify the sample matrix, the type and optimum amount of the modifier were investigated with a given concentration of Pb solution. In fact, if the matrix is not modified, lead has low ashing and atomization temperatures as to give a low absorbance with bad reproducibility because of its volatility. Therefore, optimum modifiers should be used to stabilize the atomization. In this work, the ashing and atomization temperatures were raised from 400 and $1800^{\circ}C$, to 1,000 and $2000^{\circ}C$, by the addition of palladium to 50 ng/mL lead solution as a modifier. The concentration of palladium was 5.0 ${\mu}g/mL$ in the modified solution. Furthermore, if 1.5 ${\mu}g/mL$ of aluminum was mixed with the palladium modifier as an auxiliary modifier, the ashing temperature could be increased $150^{\circ}C$ additionally. With such a treatment, the sensitivity was improved more than 5 times of the solution unmodified and the reproducible results of less than 5% RSD were obtained in the samples of university's waste water and pipe-washing tap water. It could be concluded that this procedure was quantitative in the determination of trace lead from the recoveries of more than 88% obtained in the samples in which a given amount of lead was spiked.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.11 s.170
• /
• pp.1922-1928
• /
• 1999

Rotary bending fatigue tests were carried out to investigate the influence of artificial defects on fatigue limit in annealed and austempered ductile iron. Obtained main results are as follows : (1) Artificial defect(micro hole type, dia.<0.4 mm) on specimen surface did not bring about a obvious reduction of fatigue limit in austempered ductile iron(ADI) as compared with annealed ductile iron. (2) According to the investigation of $\sqrt{area}_c$ which is the critical defect size to crack initiation at artificial defect, $\sqrt{area}_c$ of ADI is larger than that of annealed ductile iron. This shows that the situation of crack initiation at artificial defect in ADI is more difficult in comparison with annealed ductile iron. (3) One of the reasons for the low rate of crack initiation from artificial defect in ADI is that the resistance of matrix to crack initiation is higher than that of annealed ductile iron. (4) In case that the $\sqrt{area}$ of artificial defect and graphite nodule is the same, the rate of crack initiation from graphite nodule is higher than that from artificial defect. This reason is that the serious ruggedness around graphite nodule is formed by austempering treatment.

• Membrane and Water Treatment
• /
• v.8 no.1
• /
• pp.89-112
• /
• 2017

Dyeing wastewaters are the most problematic wastewater in textile industries and also, growing amounts of waste fibers in carpet industries have concerned environmental specialists. Among different treatment methods, membrane filtration processes as energy-efficient and compatible way, were utilized for several individual problems. In this research, novel hybrid membranes were prepared by waste fibers of mechanical carpets as useful resource of membrane matrix and industrial graphite powder as filler to eliminate Chrysophenine GX from dyeing wastewater. These membranes were expected to be utilized for first stage of hybrid membrane filtration process including (adsorption-ultrafiltration) and nanofiltration in Kashan Textile Company. For scaling of membrane filtration process, fouling mechanism of these membranes were recognized and explained by the use of genetic algorithm, as well. The graphite increased rejection and diminished permeate flux at low concentration but in high concentration, the performance was significantly worsened. Among all hybrid membranes, 18% wt. waste fibers-1% wt. graphite membrane had the best performance and minimum fouling. The maximum pore size of this optimum membrane was ranged from 16.10 to 18.72 nm.

• Journal of Korea Foundry Society
• /
• v.7 no.1
• /
• pp.53-59
• /
• 1987

In order to study the infuence of Sb addition on the compacted vermicular graphite cast iron(C/V) and gray cast iron(GC), these specimen which had different Sb content(0-0, 1wt.%) were prepared. these specimen were tested for microstructure and mechanical properties. The result from this study are as follows. For C/V and GC, the microstructure of graphite appeared to be finer with increasing Sb content more than 0.06wt.% Ferrite disappeared from the matrix with addition of Sb more than 0.06wt.% in GC and more than 0.08wt.% in C/V. The size of the eutectic cell in GC was 4.5 to 7 times larger than that in C/V, but the decreasing tendancy of its size was more remarkable in GC than in C/V with increasing Sb content. The abrasion speed corresponding to the maximum amount of abrasion in the nabrasion test was found to be 1.37m/sec. GC sample weared 3.6 to 21 times faster than those of C/V did. the amount of abrasion demeased remarkably with Sb addition, and the abrasion rate was constant with Sb content over 0.04wt.%

• Analytical Science and Technology
• /
• v.8 no.3
• /
• pp.273-279
• /
• 1995

Lyophilized whole blood samples containing various concentrations of Pb and Cd have been prepared as external quality control materials. These materials have been characterized with graphite furnace atomic absorption spectrometry(GFAAS), The optimized conditions for the quantitative determination of Ph and Cd in whole blood using GFAAS were obtained at the ashing temperature of $600{\sim}650^{\circ}C$ with 0.1% ammonium dihydrogen phosphate and 0.1% Triton X-100 as matrix modifier. Homogeniety and stability of the prepared whole blood have been studied at the optimized analytical condition.

• Nuclear Engineering and Technology
• /
• v.47 no.5
• /
• pp.617-623
• /
• 2015

$ZrO_2$-based composites reinforced with 6.5 vol.% of carbon foam, carbon fiber, and graphite were fabricated using spark plasma sintering, and characterized using scanning electron microscopy and X-ray diffractometry. Their thermal properties were also investigated. The microstructures of the reinforced composites showed that carbon fiber fully reacted with $ZrO_2$, whereas carbon foam and graphite did not. The carbothermal reaction of carbon fiber had a negative effect on the thermal properties of the reinforced $ZrO_2$ composites because of the formation of zirconium oxycarbide. Meanwhile, the addition of carbon foam had a positive effect, increasing the thermal conductivity from 2.86 to $3.38Wm^{-1}K^{-1}$ at $1,100^{\circ}C$. These findings suggest that the homogenous distribution and chemical stability of reinforcement material affect the thermal properties of $ZrO_2$-based composites.

• Laser Solutions
• /
• v.18 no.2
• /
• pp.1-4
• /
• 2015

This study is related to the surface hardening treatment to spheroidal graphite cast iron for die by using high power diode laser. Laser device used in this experiment is capable of real-time laser power control. This is because the infrared temperature sensor (two color pyrometer) attached to the optical system measures the surface temperature of specimen and adjusts the laser power in real time. The surface treatment was carried out with the change of heat treatment temperature at the beam travel speed 3 mm/sec. Hardened width and depth was measured and hardened zone was analyzed by micro vickers hardness test in order to research the optimum condition of heat treatment. The changes in microstructure of the hardened zone also was examined. As a result of hardness measurement and observations on microstructure of hardened zone, hardness increased over three times as compared with base metal because the martensite was formed on the matrix structure.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.04b
• /
• pp.13-19
• /
• 1996

The tribological properties of the aluminum short fiber and glass fiber reinforced tin-bronze matrix composites manufactured by vacuum hot pressing was studied. The effect of the composition and the relative density on the wear properties was examined by a reciprocal type tribo-test machine. The results were discussed by the observation of the microstructure of sintered specimen and worn surface observation using SEM and EDS. Addition of the fibers led to the wear resistance since the metal matrix was reinforced by the fibers. The reinforcement of the fiber seemed to be stronger as the distribution of the fibers was more uniform. Graphite also reduce the wear loss. The pores in the sintered composites seemed to play an important role to improve the wear resistance since the pores provide the places where the solid lubricants locate.

• KSTLE International Journal
• /
• v.2 no.2
• /
• pp.150-153
• /
• 2001

The effects of humidity on friction performance of automotive brake materials were studied using a pad-on-disk type friction tester. Three different friction materials based on a simple formulation were investigated by changing the solid lubricant graphite, MoS$_2$, and Sb$_2$S$_3$. Friction materials without solid lubricants were also examined to study the effect of other ingredients in the matrix on humidity. The friction material containing graphite was strongly affected by the humidity showing lower friction coefficient at high humidity level than other conditions. On the other hand, the friction material containing MoS$_2$exhibited higher friction coefficient at initial stage under high humidity level. The friction material without solid lubricant or with Sb$_2$S$_3$ was not affected by humidity conditions. However, the friction material containing barite showed strong speed dependence.

• 한국기계연구소 소보
• /
• s.9
• /
• pp.83-93
• /
• 1982

The influence of different heat treatment conditions on microstructure, mechanical and fatigue properties of Spheroidal Graphite cast Iron with 0.4-0.6% Mn was investigated. 1) Maximum tensile strength was arrived by tempering at about $450^{\circ}C$after quenching. Tempering at higher than $600^{\circ}C$ was changed martensitic structure to ferritic structure and secondary graphites were precipitated. 2) The relationship between matrix hardness and total hardness of the specimens are as following. [HB]$T$=0.7[HB] [HB]$M$+35 Maximum tensile strength was arrived at the total hardness of HB400-450. 3) Endurance ratio decreases with increasing total hardness, and fatigue limits can be presumed from as following. $\sigmaf$=$\sigmat$