• Communications of the Korean Mathematical Society
• /
• v.37 no.1
• /
• pp.303-326
• /
• 2022

Our aim is to construct Hermite-type exponentially fitted interpolation formulas that use not only the pointwise values of an 𝜔-dependent function f but also the values of its first derivative at three unequally spaced nodes. The function f is of the form, f(x) = g₁(x) cos(𝜔x) + g₂(x) sin(𝜔x), x ∈ [a, b], where g₁ and g₂ are smooth enough to be well approximated by polynomials. To achieve such an aim, we first present Hermite-type exponentially fitted interpolation formulas I_N built on the foundation using N unequally spaced nodes. Then the coefficients of I_N are determined by solving a linear system, and some of the properties of these coefficients are obtained. When N is 2 or 3, some results are obtained with respect to the determinant of the coefficient matrix of the linear system which is associated with I_N. For N = 3, the errors for I_N are approached theoretically and they are compared numerically with the errors for other interpolation formulas.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.26 no.4
• /
• pp.244-262
• /
• 2022

In this paper, we analyze the hybridizable discontinuous Galerkin (HDG) method for second-order elliptic equations with nonlinear coefficients, which are used in many fields. We present the HDG method that uses a mixed formulation based on numerical trace and flux. Under assumptions on the nonlinear coefficient and H²-regularity for a dual problem, we prove that the discrete systems are well-posed and the numerical solutions have the optimal order of convergence as a mesh parameter. Also, we provide a matrix formulation that can be calculated using an iterative technique for numerical experiments. Finally, we present representative numerical examples in 2D to verify the validity of the proof of Theorem 3.10.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.31 no.6_2
• /
• pp.577-583
• /
• 2013

Recently, massive archives of ground information imagery from new sensors have become available. To establish a functional relationship between the image and the ground space, sensor models are required. The rational functional model (RFM), which is used as an alternative to the rigorous sensor model, is an attractive option owing to its generality and simplicity. To determine the rational polynomial coefficients (RPC) in RFM, however, we encounter the problem of obtaining a stable solution. The design matrix for solutions is usually ill-conditioned in the experiments. To solve this unstable solution problem, regularization techniques are generally used. In this paper, we describe the effective determination of the optimal regularization parameter in the regularization technique during RPC derivation. A brief mathematical background of RFM is presented, followed by numerical approaches for effective determination of the optimal regularization parameter using the Euler Method. Experiments are performed assuming that a tilted aerial image is taken with a known rigorous sensor. To show the effectiveness, calculation time and RMSE between L-curve method and proposed method is compared.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.122-128
• /
• 2001

The objective of the present study was to investigate the characteristics of the friction and wear according to the amount of ion-irradiation for the carbon fiber reinforced plastic(CFRP). Unidirectional carbon fiber reinforced composites were fabricated with epoxy resin as a matrix and carbon fiber as a reinforcement, and its surface was modified by the ion-assisted reaction. When the amount of ion-irradiation was $1{\times}10^{16}$ ions/$cm^2$, the friction coefficients of composites were about 0.1 and the wear mode was stable, whereas, the friction coefficient of non-treatment composites were about 0.16 and the wear mode was very unstable. But if the amount of ion-irradiation was $5{\times}10^{16}$ ions/$cm^2$, the friction coefficients were higher rather than that of $1{\times}10^{16}$ ions/$cm^2$. Consequently, the amount of ion-irradiation was not in proportion to the friction coefficients, and it was conformed that the optimal conditions would exist between broth of them.

• Journal of KSNVE
• /
• v.5 no.4
• /
• pp.565-575
• /
• 1995

Gearboxes are often used in the petrochemical and electrical power plants to transmit mechanical power between two branches of a machinery train rotating at different speeds. When the gearboxes are connected with rotors supported by journal bearings, bearing loads vary in magnitude and direction with rotor speed and torque transmitted by the gearboxes. In this study, dynamic characteristics of the system which consists of gearboxes and a rotor supported by journal bearings are investigated analytically and experimentally by employing the polynomial transfer matrix method and modal analysis under different speeds and torque levels. Journal bearing loads due to the transmitted torque are claculated analytically and the stiffness and damping coefficient of the journal bearings are obtained using finite element method. Comparison of the analytical and experimental results shows that the cross coupled stiffness coefficients increase with increasing rotor speed, while the cross coupled damping coefficients decrease. This generates the oil whirl instability in the journal bearings. As the transmitted torque level goes up, the stiffness coefficients of the journal bearing and the first horizontal natural frequency increase. High levels of the transmitted torque produce high bearing stiffness since the contact loads of the mating gear teeth increase. The logarithmic decrement, which is a stability indicator, is shown to decrease with increasing speed and decreasing torque. Thus, at the low torque level, the system become unstable even at the low shaft speed.

• Speech Sciences
• /
• v.10 no.2
• /
• pp.249-258
• /
• 2003

This study attempted to examine a speaker identification method using difference sum and correlation coefficient determined from a pair of intensity level matrices of band-pass-filtered numeric sounds produced by ten female speakers of similar age and height. Subjects recorded three digit numbers at a quiet room at a sampling rate of 22 kHz on a personal computer. Collected data were band-pass-filtered at five different band ranges. Then, matrices of five intensity levels at 100 proportional time points were obtained. Pearson correlation coefficients and the sum of absolute intensity differences between a pair of given matrices were determined within and across the speakers. Results showed that very high correlation coefficient and small difference sum generally occurred within each speaker but some individual variation was also observed. Thus, the matrix pair with a higher coefficient and a smaller difference sum was averaged to form each individual's model. Comparison among the speakers yielded generally low coefficients and large differences, which suggests successful speaker identification, but among them there were a few cases with very high coefficients and small differences. Future studies will focus on finer band ranges and additional spectral parameters at some peak points of the intensity contour at a low frequency band.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.1
• /
• pp.130-140
• /
• 1998

This paper presents a method to estimate subpixel accuracy motion vectors using a mathermatical model withoug interpolation. the proposed method decides the coefficients of mathematical model, which represents the motion vector which is achieved by full search. And then the proposed method estimates subpixel accuracy motion vector from achieved mathematical model. Step by step mathematical models such as type 1, type 2, type 3, modified bype 2, modified type 3, and Partial Interpolation type 3 are presented. In type 1, quadratic polynomial, which has 9 unknown coefficients and models the 3by 3 pixel plane, is used to get the subpixel accuracy motion vectors by inverse matrix solution. In type 2 and 3, each quadratic polynomial which is simplified from type 1 has 5 and 6 unknown coefficients and is used by least square solution. Modified type 2 and modified type 3 are enhanced models by weighting only 5 pixels out of 9. P.I. type 3 is more accurate method by partial interpolation around subpixel which isachieved by type 3. LThese simulation results show that the more delicate model has the better performance and modified models which are simplified have excellent performance with reduced computational complexity.

• Tribology and Lubricants
• /
• v.18 no.1
• /
• pp.61-67
• /
• 2002

The objective of the present study was to investigate the characteristics of the friction and wear according to the amount of ion-irradiation for the carbon fiber reinforced plastic (CFRP). Unidirectional carbon fiber reinforced composites were fabricated with epoxy resin as a matrix and carbon fiber as a reinforcement, and its surface was modified by the ion-assisted reaction. When the amount of ion-irradiation was $1{\times}10^{16}$ $ions/cm^{2}$. the friction coefficients of composites were about 0.1 and the wear mode was stable. whereas, the friction coefficient of non-treatment composites were about 0.16 and the wear mode was very unstable. But if the amount of ion-irradiation was $5{\times}10^{16}$ $ions/cm^{2}$, the friction coefficients were higher rather than that of $1{\times}10^{16}$ $ions/cm^{2}$ Consequently. the amount of ion-irradiation was not in proportion to the friction coefficients, and it was conformed that the optimal conditions would exist between both of them.

• Journal of Advanced Navigation Technology
• /
• v.10 no.3
• /
• pp.219-225
• /
• 2006

This paper presents a method of object classification based on discrete wavelet transform (DWT) and fuzzy inference(FI). It concentrated not only on the design of fuzzy inference algorithm which is suitable for low speed uninhabited transportation such as, conveyor but also on the minimize the number of fuzzy rule. In the preprocess of feature extracting, feature parameters are extracted by using characteristics of the coefficients matrix of DWT. Such feature parameters as area, perimeter and a/p ratio are used obtained from DWT coefficients blocks. Secondly, fuzzy if - then rules that can be able to adapt the variety of surroundings are developed. In order to verify the performance of proposed scheme, In the middle of fuzzy inference, the Mamdani's and the Larsen 's implication operators are utilized. Experimental results showed that proposed scheme can be applied to the variety of surroundings.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.10
• /
• pp.1196-1203
• /
• 2012

This paper presents a study on the calibration of a C-band HPS(Hongik Polarimetric Scatterometer) system using the DMMCT(Differential Mueller Matrix Calibration Technique). For calibration of the polarimetric scatterometer system, a fully-polarimetric antenna pattern(magnitudes and phase-differences) of the antenna main-beam is measured using a conducting sphere at anechoic chamber. The polarimetric scatterometer system could be accurately calibrated after retrieving its distortions using the DMMCT. Unlike a single-polarimetric system, in a fully-polarimetric system, not only backscattering coefficients but also phase differences are important parameters. This calibrated HPS system can be used to measure accurate Mueller matrices of bare soil surfaces, rice paddies, and vegetation fields. The phase-difference parameters as well as the backscattering coefficients for co- and cross-polarizations can then be obtained. The accuracy of calibration was verified by comparing the measured backscattering coefficients with a scattering model. The measured polarization response of a plowed bare field was also compared with the polarization response which was synthesized using a polarimetric scattering model for verifying the calibration technique.