• Journal of Biosystems Engineering
• /
• 제14권1호
• /
• pp.33-40
• /
• 1989

The flow properties of water added com-cob-mix(CCM) were studied in order to provide basic information for designing its pumping system. For the study, a model system similar to actual situation was constructed. From the experiment, it can be concluded that the flow properties of the water added CCM has close relationship with its moisture content as follows; 1. The pressure drop caused by friction was very low when the moisture content of water added CCM was more than 70%. However, when the moisture content of the material is about 60%, the pressure drop increases up to 10 kPa/m at low pumping speed, and 20 kPa/m at high pumping speed, respectively. 2. The water added CCM having about 65% moisture content showed pseudo-plastic flow characteristics. 3. As the moisture content of the material decreases, the shear stress increases more rapidly than the shear rate does. Finally, below approximately 60% moisture, the shear stress becomes a linear relationship with the shear rate. 4. It was possible to pump the material having the moisture content down to 58% through a pipe having 80 mm diameter by a pump operating at 234 rpm. However, by either increasing the diameter of the pipe or decreasing the pumping speed, it can be possible to pump the material having lower moisture content than 55%.

• 항공우주시스템공학회지
• /
• 제10권3호
• /
• pp.63-69
• /
• 2016

The properties of composite materials, when compared to those of metallic materials, are highly variable due to many factors including the batch-to-batch variability of raw materials, the prepreg manufacturing process, material handling, part-fabrication techniques, ply-stacking sequences, environmental conditions, and test procedures. It is therefore necessary to apply reliable statistical-analysis techniques to obtain the design allowables of composite materials. A new composite-material qualification process has been developed by the Advanced General Aviation Transport Experiments (AGATE) consortium to yield the lamina-design allowables of composite materials according to standardized coupon-level tests and statistical techniques; moreover, the generated allowables database can be shared among multiple users without a repeating of the full qualification procedure by each user. In 2005, NASA established the National Center for Advanced Materials Performance (NCAMP) with the purpose of refining and enhancing the AGATE process to a self-sustaining level to serve the entire aerospace industry. In this paper, the statistical techniques and procedures for the generation of the allowables of aerospace composite materials will be discussed with a focus on the pooling-across-environments method.

• 대한기계학회논문집A
• /
• 제25권3호
• /
• pp.369-380
• /
• 2001

Although extensive efforts have been devoted to the optimal design of composite laminated plates in recent years, some practical issues still need further research. Two of them are: the handling of the ply angle as either continuous or discrete; and that of the uncertainties in material properties, which were treated as continuous and ignored respectively in most researches in the past. In this paper, an algorithm for stacking sequence optimization which deals with discrete ply angles and that for thickness optimization which considers uncertainties in material properties are used for a two step optimization of composite laminated plates. In the stacking sequence optimization, the branch and bound method is modified to handle discrete variables; and in the thickness optimization, the convex modeling is used in calculating the failure criterion, given as constraint, to consider the uncertain material properties. Numerical results show that the optimal stacking sequence is found with fewer evaluations of objective function than expected with the size of feasible region taken into consideration; and the optimal thickness increases when the uncertainties of elastic moduli considered, which shows such uncertainties should not be ignored for safe and reliable designs.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.1-6
• /
• 2004

This paper shows the study on the design and another applications of the spray-freeze dryer for the production of valuable material powders. Powder production and handling has been an integral part of material extracting processing and pharmaceutical processing because of the wide use of oral dosage forms. There are a few commonly used powder preparation methods including mechanical milling, precipitaion, spray drying, freeze drying, and so on. In general, methods available for preparing inhalation powders are limited due to certain inhalation powder's sensitive nature to the processing environments. This is particularly true for preparing dry powder aerosols where the aerodynamic particle size($<5{\mu}m$) and the size distribution are pivotal. Supercritical fluid antisolvent and spray freeze drying have recently emerged as promising techniques for producing powders for use in microcapsulation. However, the aerosol applications of these powders are yet to be explored. The purpose of this study is to test the feasibility of using spray freeze-dried valuable material powders for aerosolization.

• Journal of Pharmaceutical Investigation
• /
• 제32권1호
• /
• pp.41-45
• /
• 2002

The purpose of this study is to microencapsulate a highly hygroscopic drug, pyridostigmine bromide (PB), with a waterproof wall material, in order to increase the flowability of the drug particles. Polyvinylacetaldiethylaminoacetate (AEA), Eugragit E and Eugragit RS were examined as the wall materials. Microcapsules containing PB were prepared by the evaporation technique in an acetone/liquid paraffin system using aluminum tristearate as a core material, and evaluated for drug encapsulation efficiency, surface morphology, particle size and drug dissolution. The encapsulation of PB in the wall material was almost complete. Among the wall materials examined, AEA exhibited the most excellency in shape, surface texture, flowability, size distribution of microcapsules. Above results suggest that AEA would be a potential wall material for microcapsulation of highly hygroscopic drugs, such as PB. Through microencapsulation with AEA, inconvenience of handling of PB powders encountered in the process of weighing and packing the powders to tableting die or capsule body could be greatly improved.

• 대한기계학회논문집A
• /
• 제39권12호
• /
• pp.1265-1273
• /
• 2015

석탄하역기는 화력발전소의 주 원료인 석탄을 체인 버킷을 구동하여 선박으로부터 컨베이어 벨트로 하역하는 장비이다. 그러나 국내에서는 석탄하역기의 하역위치에 따라 붐 각도를 제어하는 유압시스템인 붐 호이스팅 실린더에 대한 연구가 이루어지지 않아, 전량 수입하고 있는 실정이다. 이에 본 연구에서는 두꺼운 실린더에서 접촉면압의 이론 값을 FEM 을 수행하여 얻은 결과 값과 비교하여 접촉면압 해석기법의 타당성을 확립하였고, 이를 통하여 브이 실을 갖는 붐 호이스팅 실린더에서 작동유의 누설 여부 판단과 접촉면압을 최대로 갖는 브이 실 형상을 설계하였다. 또한, 실린더의 스트로크에 따른 구동시뮬레이션을 수행하였고, 최대 출력 상태에서의 붐 호이스팅 실런더의 구조 안전성을 검증하였다.

• 한국산업보건학회지
• /
• 제26권4호
• /
• pp.454-465
• /
• 2016

Objectives: The purpose of this study was to evaluate trends in asbestos exposure among asbestos-handling industries from 2000 to 2005. Methods: The data included the number of industries and workers exposed, concentrations of asbestos and the amount exceeded, and the type and size of industry by year. These data were collected by 46 regional employment and labor offices in Korea using work environment monitoring reports. A total of 1,481 samples from 284 industries were extracted from the reports and were analyzed with no data modification. Results: The means of asbestos concentration decreased from $0.84f/cm^3$ to $0.03f/cm^3$ during the period 2000-2005. Among the total of 1,481 samples, 11 samples(0.7%) exceeded the KOEL, and 178 samples(12.0%) were ACGIH TLV. The insulating paper product manufacturing industry was found to have the highest level of asbestos, followed by the fireproofing manufacturing industry, brake lining products manufacturing industry, commutator products manufacturing industries, and construction materials manufacturing industry. The number of asbestos handling industries decreased from 48 industries with 1,155 employees to 37 industries during the period of 2000 to 2005, but the number of asbestos workers expanded to the point that 1,182 employees could be found in 2005. Conclusion: Based on these results, the strengthening of the KOEL and new regulations turned out to help reduce asbestos exposure levels. This study recommends that retrospective exposure to asbestos based on various industry types should be assessed.

• 대한안전경영과학회지
• /
• 제18권4호
• /
• pp.57-72
• /
• 2016

There are more than 30,000 chemical substances handled in domestic university laboratories. Among them, hazardous materials are selected and managed as designated substances by the standards of 19 Ministries and 16 Acts. However, domestic safety-related laws and regulations are used to manage industrial risk factors based on industrial activities. In case of installing a university chemical laboratory in accordance with the installation standards applicable to general workplaces. It is not suitable to use as a laboratory installation standard that can be applied to a chemical laboratory installed at a university such as a problem occurs in applying to a university using a small quantity of dangerous substances in a small amount. In order to establish the laboratory structure and facility standards that are appropriate for the laboratory characteristics and apply systematic laboratory safety, the National Security Administration shall apply the special handling standard of chemical experiment to places where handling less than 30 times the designated quantity of chemical substances for chemical experiments. On August 2, 2016, the regulations for the enforcement of the Dangerous Goods Safety Management Act and the standards for the structure and facilities of the university chemical laboratory were enacted. In this study, we investigated the domestic chemical substances laws and regulations to determine the chemical substances that are over-regulated in the relevant laws, and define them as substances against accidents. The management criteria for the substances were analyzed. The R value for the designation of the designated quantity by the concept of the space in the management standard was calculated.

• 한국산업보건학회지
• /
• 제25권4호
• /
• pp.506-515
• /
• 2015

Objectives: This study was conducted to evaluate the status of hazard communication regarding dental materials among dental hygienists in the Daegu Metropolitan City and the North Gyeongsang-do Province area. Materials: A total of 310 dental hygienists were surveyed using self-administered questionnaires to investigate the status of hazard communication on dental materials and information needs. We collected instructions for use and material safety data sheets(MSDSs) for 67 dental materials frequently used at dental hospitals located in the Daegu Metropolitan City and the North Gyeongsang-do Province area. Results: The questionnaire surveys showed that only 11% of the 310 dental hygienists had knowledge of MSDS and 46.8% of respondents never read instructions for use before using materials. Just 7.4% of dental hygienists have undergone training on hazard information for dental materials. In particular, dental hygienists working at dental clinics had significantly lower response rates on knowledge of MSDS(p<0.001), reading of instructions for use(p=0.042) and training on the hazard information of dental materials(p=0.004) than those in dental hospitals or general hospitals. The essential information most desired by dental hygienists was hazard identification(82.3%) followed by first-aid measures(53.9%), handling and storage(51%), disposal considerations (49%) and toxicological information(47.1%). All dental materials were on foreign products which came from Japan(59.7%), the USA(26.9%) and Liechtenstein(13.7%). In terms of usage, 56.7% of dental materials were prosthetic, followed by conservation(31.3%), orthodontics(9%), and prevention(3%). We found that dental hygienists had accessed MSDSs for only five dental products among the 67 dental materials. The instructions for the use of the 67 dental materials provided hazard identification(64.2%), first-aid measures(83.6%), handling and storage(97%), disposal considerations(20.9%) and toxicological information(26.9%). Conclusions: Based on the results of this study, the hazard communication system for dental hygienists working at dental clinics should be improved.

• 한국산업보건학회지
• /
• 제27권4호
• /
• pp.423-432
• /
• 2017

Objectives: This study was conducted to evaluate asbestos handling history of workers at automobile manufacturing plants in Korea. Methods: National regulations on asbestos and Korea Occupational Safety and Health Agency(KOSHA) database on the information of asbestos containing products were reviewed. We investigated asbestos related materials from one automobile manufacturing plant. Material safety data sheets(MSDS) collected in 2010, work environment monitoring results reported from 2000 to 2013, trade union reports and asbestos survey reports were reviewed. We also interviewed workers with long career and did walk-through survey. Results: The Ministry of Labor in Korea has permitted asbestos manufacturing since 1990. In 1997, the use of crocidolite and amosite asbestos were banned. In 2007, the Korean government announced a total ban on the manufacturing, importation and use of all kinds of asbestos, which took full effect in 2009. A total of 174 asbestos products information from KOSHA database was analyzed. Extruded cement panel for building, special brake for crane farm machinery, gasket, joint sheet and thermal insulator were produced until 2007. From automobile manufacturing plant survey, we confirmed that asbestos containing materials(ACM) such as gasket, heating induction materials have been used until 2011. Asbestos containing building materials(ACBM) such as bamlites, slate and ceiling tex were reported at 122 asbestos dismantling projects in 2014. Conclusion: Although the use of all kinds of asbestos were banned from 2009, ACMs and ACBMs installed before 2009 were still found at automobile manufacturing plant until 2011 and 2014 respectively. In particular, asbestos slates should be managed because most of slates had not been removed until 2014.