• The Journal of the Petrological Society of Korea
• /
• v.15 no.2 s.44
• /
• pp.60-71
• /
• 2006

The Seokmodo consists mainly of biotite granite and granodiorite. The biotite granite is divided into the south and the north part by granodiorite. There occurs high temperature hot spring of which temperature is up to $72^{\circ}C$. The Rb-Sr isotopic data for the biotite granite define whole-rock isochron ages of $207{\pm}70$ Ma with initial Sr isotopic ratio of 0.7132 in north part and $132{\pm}50$ Ma with initial Sr isotopic ratio of 0.7125 in south part, suggesting that the magma be derived from the crustal source material. The geochemical characteristics of the biotite granite and hornblende granodiorite indicate that they were crystallized from calc-alkaline under syn-collisional tectonic environment. The samples of hot spring were collected at March 2005 and March 2006. The $^{87}Sr/^{86}Sr$ ratios of hot spring are 0.714507 and 0.714518, respectively and correspond to those oi the granite being occurred at the south part. The similarity of $^{87}Sr/^{86}Sr$ ratios between the granite and hot spring strongly suggests that the hot spring might be derived from the Seokmodo biotite granite.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.5
• /
• pp.543-561
• /
• 2020

This paper is the result of the study on the effect of the support structure of the tunnel steel rib. In tunnel excavation, the top and bottom half excavation methods result in subsidence of steel rib reinforcement due to insufficient support of steel rib reinforcement when the ground is poor after excavation. The foundation of the steel rib installed in the upper half excavates the bottom part of the base, causing the subsidence to occur due to various effects such as internal load and lateral pressure. As a result, the tunnel is difficult to maintain and its safety is problematic. To solve these problems, steel rib support structures have been developed. For the purpose of verification, the behavior of the supporting structure is verified by model experiments reduced to shotcrete and steel rib material similarity, the numerical analysis of ΔP and ΔP generated by bottom excavation by Terzaghi theoretical equation. As a result, it was found that the support structure of 20.100~198.423 kN is required for the 10~40 m section of the depth for each soil of weathered soil~soft rock. In addition, as a result of the reduced model experiment, a fixed level of 50% steel rib deposit of steel rib support structure was installed. The study shows that the installation of steel rib support structures will compensate for uncertainties and various problems during construction. It is also thought that the installation of steel rib support structure will have many effects such as stability, economy, and air reduction.

• The Journal of Art Theory & Practice
• /
• no.13
• /
• pp.97-132
• /
• 2012

1799 Francisco de Goya published Los Caprichos with 80 aquatint etchings. On 6 February he advertised it on the front page of the Diario de Madrid. The long advertisement which began with "a collection of prints of capricious subjects, invented and etched by Don Francisco Goya" informed purpose, themes and methods of this collection of prints. According to this advertisement Goya "has chosen as subjects for his work, from the multitude of follies and mistakes common in every civil society and from the vulgar prejudices and lies authorized by custom, ignorance or self-interest, those that he has thought most fit to provide material for ridicules, and at the same time to exercise the artist's imagination." The text emphasized that the 'author' of this series didn't to want to criticise any individual and to be a copyist. From his phantasy Goya invented many creatures like the anthropic, humanized animals etc.. With Los Caprichos he stood on the threshold to Romanticism. The early researchers of Los Caprichos classified its author, Goya as an enlightened intellectual. The similarity of the themes of the series with the subjects of the Enlightenment, his some enlightened 'friends' and the idea to avoid the prevalent mystification of his life supported this theory. But this trend became revised since the 80's of the last century. This made possible to research Goya's works in new perspective and to see that Goya didn't criticise the Spanish society and his contemporaries. Rather he showed its reality and parodied through creatures which are mixtures of the reality that he observed, and visions that he invented. Characters and scenes in Goya's prints are ambiguous and equivocal. They have the values which are defined by the dualistic metaphysic in Europe as oppositional, like good and evil for example, at the same time. Goya himself also appeared in various types in this series. This ambiguousness, or "polyphony", as Jennis Tomlinson defined, is a symptom of the decay of the belief in the Enlightenment which spreaded in Europe as a result of the attack of Bastille and the French Revolution. Goya's self-portrait in pl. 43 of this series, "El sue$\tilde{n}$o de la razon produce monstruos" shows the complex psychology of him and his contemporaries as well. As the rest etchings after this print show witchcraft and monsters reside in the world in which the reason of the Enlightenment and the through the reason weakened God's rule lost their authority. In this thesis I will examine and analyse how Goya represented in Los Caprichos the nature of man and its society, as complex being in which the 'antagonistic' value couple as good and evil couldn't be divided, but are united.

• The Research Journal of the Costume Culture
• /
• v.16 no.6
• /
• pp.1050-1063
• /
• 2008

A movie is a fiction made on a basis of an author's and a writer's imagination, but all sorts of properties mixed with each other and most realistically expresses the era which becomes the background of a movie and acts as a carrier that connects designers with consumers. Thus, this study was carried out to review how the fashion products that designer's intention and commercial value added are expressed in collections by comparing and analysing the costumes in the movie "The Great Gatsby" that described the life of America's upper-class in 1920s and the 04 S/S Y&Kei collection which were proceeding after getting inspiration from this movie. For this, literature materials were inspected in order to make a theoretical review on social and cultural background and costumes history background in 1920s and the photo materials on movie costume were collected and analysed using DVD video captures, as well as the photo materials on 04 S/S Y&Kei were collected and analyzed through the institute providing domestic fashion information. The following conclusion was deduced through this study. First, in 1920s which becomes the background of this study, the slim shape of Flapper which looks like a young and boy became an ideal figure condition and the straight silhouette with low waist line and the short skirt that rose to knee was popular. Second, as a result of analysing movie costume by classifying it in silhouette, colors, and materials, straight silhouette of low waistline with a near colored - tone seen in the pastel series, including white, beige, pink, and gray was mainly constituted and the metal colors like silver and gold were used. As a material, chiffon, satin, velvet, flower patterned prints, and beads were used, which represented luxurious life of women in the upper classes. Third, as a result of comparing and analysing, it turned out that there was a similarity. However, in dress collection for a heroine, some dissimilarity differentiated from a movie costumes was found out in that the dresses in collection expressed moderate beauty and modernism and elegant beauty at the same time by matching a variety of materials and using black color.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.9
• /
• pp.630-635
• /
• 2013

There is a need to establish systematic procedure of groundwater quality standards, however, there were no specified basis for establishing substances and values in Korean groundwater quality standards for non-drinking water. In this study, we reviewed basis for deriving groundwater quality standard in the developed countries, considering carcinogenic and non-carciongenic risk via inhalation and dermal contact exposure pathways. Also, we reviewed the prior systematic procedure of standards related to water quality (e.g. drinking water, surface water, and wastewater). USEPA RAGS, ASTM RBCA, and Massachusettes presented the formulas for deriving groundwater concentrations of chemicals and there were similarity and differences. We suggests systematic procedure of groundwater quality standards, as follows. (1) Selection of groundwater pollutants population, (2) Possibility of risk assessment, (3) Selection of monitoring priority substances, (4) Monitoring, (5) Risk assessment, (6) Selection of groundwater quality standard candidates, (7) Selection of new substances and values for groundwater quality standards. Especially, groundwater concentration of hazardous material were presented according to revised risk formulas via inhalation and dermal contact.

• Korean Journal of Plant Resources
• /
• v.19 no.1
• /
• pp.161-168
• /
• 2006

To investigate the origin of backyeoncho (Opuntia ficus-indica var. saboten), we isolated 685 bp clone using ITS primer pairs. The rDNA consists of the genes coding for the partial 54 bp 185, 162 bp 5.8S, and partial 56 bp 26S. The coding regions are interrupted by two internal transcribed spacers, 193 bp ITS1 and 220 bp ITS2. The ITS2 of backnyeoncho in length was shorter than that previously registered in Cucurbitoideae plants. The GC contents was 66.8% in ITS1, and 67.7% in ITS2. The rDNA of backnyeoncho matched to the previously reported genes and showed a high similarity with the 95% identity with Pereskiopsis porteri (L708037). In the phylogenetic analysis, the backnyeoncho rDNA was clustered with Pereskiopsis porteri (L708037).

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.24 no.2
• /
• pp.39-56
• /
• 2021

The seed zone is a map that describes the areas where plant material can be transferred with little risk for properly adapting to a new location. The seed zone study is largely divided into studies based on genetic data and studies based on climatic data. Can be. This study was conducted to establish a temporary domestic seed zone applicable to the entire Korean Peninsula and evaluate its possibility based on the US climate-based seed zone establishment methodology. The temporary seed zone was constructed in the same way as the US case by superimposing the data obtained by dividing the winter minimum temperature into 12 grades and the data obtained by dividing the annual heat: moisture index into 6 grades. As a result of the analysis, 65 temporary seed zones were formed throughout the Korean Peninsula, and the areas of the seed zones representing the smallest and largest areas were 3.0km² and 29,423.0km², respectively, and it was confirmed that they had an average size of about 5,064.9km². Temporary seed zones applied in Korea show a pattern of changes in temperature according to the relatively horizontal forest zone, and it was confirmed that the area where the Baekdu-daegan ecological axis is located has a tendency to show lower dryness than other areas. This study applied the US climate-based seed zone methodology in Korea as a pilot, and confirmed the climatic similarity across the Korean Peninsula. Furthermore, it is expected to provide an optimal seed map that improves the success rate of restoration in the future by revising the seed zone grade suitable for the domestic environment in consideration of the results of this study and the possibility of seed adaptation to the field survey and environmental space.

• Economic and Environmental Geology
• /
• v.56 no.2
• /
• pp.201-215
• /
• 2023

In the stone-lined tombs from Cheongyang Rokpyeong-ri site, several stone-lined tombs corresponding to the Three Kingdoms Period, Unified Silla Period and Goryeo Dynasty were excavated. In this study, the stone properties of petrological, mineralogical and geochemical characteristics from 15 stone-lined tombs were analyzed, the rock species and occupation rate were reviewed, also the provenance area was interpreted. There are five types of rocks used as members of the tombs, including black sandstone, greywacke, slate, conglomerate and gneiss. As a result of magnetic susceptibilities, the rocks of the tombs and presumed provenance are all shown in the same range, and the similarity between the tombs and the source area is high in geochemical behavior characteristics. The stone properties of the tombs are the same as the presumed provenance rocks and is distributed within a 500m around the bedrock of the tombs in the excavation site, so it seems that self-sufficiency was possible on the site without a special procurement system. These stones are interpreted to have been constructed through some trimming without any special technique, but some stone tombs have been confirmed to used homogeneous black sandstone at the bottom of the tombs, so it is believed that there were artificial selection of stones.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.1
• /
• pp.89-96
• /
• 2023

In this paper, a ferrosilicon by-product was evaluated to confirm the feasibility of recycling it as supplementary cementitious material of ordinary Portland cement in concrete. Three different levels of replacement ratio (10 %, 20 % and 30 % of total binder) were applied to find which is the most beneficial to be used as a binder. Ferrosilicon concrete was initially assessed at setting time and compressive strength. Durability was evaluated by the resistance to chloride penetration test(RCPT) and alkali-silica reaction(ASR) with a comparison to silica fume concrete due to their similarity in chemical composition. The porosimetry and X-ray diffraction analysis along with energy dispersive X-ray spectroscopy give information on the microstructural characteristics of the ferrosilicon concrete. It was found that 10 % ferrosilicon concrete has higher strength while 20 %, 30 % have lower strength than OPC concrete. However, chemical resistance to chloride attack is higher when replacement is increased. Compared to silica fume, the durability of ferrosilicon might be less efficient however, it is obviously beneficial than OPC. High SiO₂ content in ferrosilicon results in producing more C-S-H gel which could make denser pore structure. Most of the risk of alkali silica reaction to silicate binders through length change tests was less than 0.2 %, and both mortar using ferrosilicon and silica fume showed better resistance to alkali silica reaction as the substitution rate increased.Reuse of industrial waste rather than producing highly refined additives might reduce environmental load during manufacture and save costs.

• Advances in nano research
• /
• v.16 no.4
• /
• pp.325-340
• /
• 2024

There are several novel uses for dispersing many nanoparticles into a conventional fluid, including dynamic sealing, damping, heat dissipation, microfluidics, and more. Therefore, melting heat and mass transfer characteristics of a 3-D MHD Hybrid Nanofluid flow over a rotating disc with presenting dufour and soret effects are assessed numerically in this study. In this instance, we investigated both ferric sulfate and molybdenum disulfide as nanoparticles suspended within base fluid water. The governing partial differential equations are transformed into linked higher-order non-linear ordinary differential equations by the local similarity transformation. The collection of these deduced equations is then resolved using a Chebyshev spectral collocation-based algorithm built into the Mathematica software. To demonstrate how different instances of hybrid/ nanofluid are impacted by changes in temperature, velocity, and the distribution of nanoparticle concentration, examples of graphical and numerical data are given. For many values of the material parameters, the computational findings are shown. Simulations conducted for different physical parameters in the model show that adding hybrid nanoparticle to the fluid mixture increases heat transfer in comparison to simple nanofluids. It has been identified that hybrid nanoparticles, as opposed to single-type nanoparticles, need to be taken into consideration to create an effective thermal system. Furthermore, porosity lowers the velocities of simple and hybrid nanofluids in both cases. Additionally, results show that the drag force from skin friction causes the nanoparticle fluid to travel more slowly than the hybrid nanoparticle fluid. The findings also demonstrate that suction factors like magnetic and porosity parameters, as well as nanoparticles, raise the skin friction coefficient. Furthermore, It indicates that the outcomes from different flow scenarios correlate and are in strong agreement with the findings from the published literature. Bar chart depictions are altered by changes in flow rates. Moreover, the results confirm doctors' views to prescribe hybrid nanoparticle and particle nanoparticle contents for achalasia patients and also those who suffer from esophageal stricture and tumors. The results of this study can also be applied to the energy generated by the melting disc surface, which has a variety of industrial uses. These include, but are not limited to, the preparation of semiconductor materials, the solidification of magma, the melting of permafrost, and the refreezing of frozen land.