• Membrane and Water Treatment
• /
• 제2권2호
• /
• pp.91-103
• /
• 2011

The flux behavior in the separation of equimolar bovine serum albumin (BSA) and bovine hemoglobin (HB) in aqueous solutions by cross-flow ultrafiltration (UF) was investigated, in which polyacylonitrile membrane with a molecular weight cut-off (MWCO) of 100 kDa was used. BSA and HB have comparable molar mass (67,000 vs. 68,000) but different isoelectric points (4.7 vs. 7.1). The effects of process variables including solution pH (6.5, 7.1, and 7.5), total protein concentration (1.48 and 7.40 ${\mu}M$), transmembrane pressure (69, 207, and 345 kPa), and solution ionic strength (with or without 0.01 M NaCl) on the separation were examined. It was shown that the ionic strength had a negligible effect on separation performance under the conditions studied. Although BSA and HB are not rigid bodies, the flux decline in the present cross-flow UF did not result from the mechanism of cake filtration with compression. In this regard, the specific cake resistance when pseudo steady-state was reached was evaluated and discussed.

• 한국막학회:학술대회논문집
• /
• 한국막학회 2005년도 추계 총회 및 학술발표회
• /
• pp.245-249
• /
• 2005

• 멤브레인
• /
• 제23권6호
• /
• pp.393-408
• /
• 2013

고분자 분리막을 이용한 기체 분리막은 높은 에너지 효율, 경제적인 장점으로 최근 수년간 지속적으로 개발되어 왔다. 최적화된 경제적 성능을 얻기 위하여 기체 분리막은 높은 투과도와 선택도를 가져야 한다. 따라서 기체분리 분리막용으로 다양한 고분자를 시험한 연구 결과들이 보고되어 왔다. 다양한 소재 중, 폴리이미드는 다양한 기체인자에 대하여 높은 투과 선택도와 높은 화학적 열적 안정성, 그리고 물리적 안정성으로 많은 주목을 받아왔다. 따라서 본고에서는 기체분리용 폴리이미드 소재의 개발동향과 분리막의 제조방법, 기체 분리의 원리에 대하여 다루었다.

• 한국전기전자재료학회논문지
• /
• 제30권5호
• /
• pp.301-306
• /
• 2017

Wire electrical discharge machining (WEDM) process was evaluated to slice Silicon (Si) for various applications. Specifically, various Si workpieces with various resistances, such as single and multi crystalline Si bricks and wafers were used. As conventional slicing processes, such as slurry-on or diamond-on wire slicing, are based on mechanical abrasions between Si and abrasive, there is a limitation to decrease the wafer thickness as well as kerf-loss. Especially, when the wafer thickness is less than $150{\mu}m$, wafer breakage increases dramatically during the slicing process. Single crystalline P-type Si bricks and wafers were successively sliced with considerable slicing speed regardless of its growth direction. Also, typical defects, such as microcracks, craters, microholes, and debris, were introduced when Si was sliced by electrical discharge. Also, it was found that defect type is also dependent on resistance of Si. Consequently, this study confirmed the feasibility of slicing single crystalline Si by WEDM.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.201-203
• /
• 2011

The purpose of this study was to develop and evaluate of fire resistive cladding systems for HSC(high-strength concrete) column, which was mainly constructed with aerogel blanket insulation material. The aerogel blanket-fire protective gypsum board cladding system showed that it clearly secure the fire resistance performance of HSC column when the reinforcing measures had achieved for four cross-sectional edge sides of structure and the system is well continued during the test period with no significant deformation or separation etc. It was checked out the 20mm thickness cladding system consist with AG(5mm)+FGB(15mm) can secure 3hour-fire resistance performance adequately.

• Korean Membrane Journal
• /
• 제1권1호
• /
• pp.50-58
• /
• 1999

Symmetric asymmetric and composite perfluoropolymer membranes made with HYFLON AD have been prepared and evaluated. Porous and non porous symmetric membranes have been prepared by solvent evaporation with various processing conditions. Non-contact atomic force microscopy (AFM) was used to investigate the membrane morphology in air. Analysis of the images gave quantitative imformation on the surface pore strcture in particular on the pore size distributin. Possible useful uses of porous membranes are envisaged in the field of gas-liquid separations such as membrane contactors (MSc) Molecular Dynamics(MD) simulations structure of HYFLON AD 60X copolymer supporting these results are also reported. Amorphous perfluoropolymer membranes appears to be ideal other than in MCs when separation processes have to be performed in hostile environments i.e. high temperatures and aggressive non-aqueous media such as chemicals and solvents. In these cases HYFLON AD mem-branes can exploit the outstanding resistance of perfluoropolymers.

• 한국인쇄학회지
• /
• 제15권2호
• /
• pp.131-143
• /
• 1997

Surface sizing is one of the important process to the paper making. Surface sizing had an effect on penetration of oils, physical propertiesm water resistance for the paper. This study was carried out for the purpose of improving printability with surface sizing of domestic newspaper. The samples were prepared by means of TAPPI method(TAPPI 205 om~88), and were wested by IGT printability tester. The results of this study showed that the set-off was reduced on the surface sized with oxidized starch.

• Nuclear Engineering and Technology
• /
• 제40권7호
• /
• pp.581-592
• /
• 2008

In this study, a conceptual pyroprocess flowsheet has been devised by combining several dry-type unit processes; its applicability as an alternative fuel cycle technology was analyzed. A key point in the evaluation of its applicability to the fuel cycle was the recovery yield of fissile materials from spent fuels as well as the proliferation resistance of the process. The recovery yields of uranium and transuranic elements (TRU) were obtained from a material balance for every unit process composing the whole pyroprocess. The material balances for several elemental groups of interest such as uranium, TRU, rare earth, gaseous fission products, and heat generating elements were calculated on the basis of the knowledge base that is available from domestic and foreign experimental results or technical information presented in open literature. The calculated result of the material balance revealed that uranium and TRU could be recovered at 98.0% and 97.0%, respectively, from a typical PWR spent fuel. Furthermore, the anticipated TRU product was found to emit a non-negligible level of $\gamma$-ray and a significantly higher level of neutrons compared to that of a typical plutonium product obtained from the PUREX process. The results indicate that the product from this conceptual pyroprocessing should be handled in a shielded cell and that this will contribute favorably to retaining proliferation resistance.

• 멤브레인
• /
• 제15권4호
• /
• pp.289-296
• /
• 2005

MBR 공정에서 가장 문제시되는 부분은 실제 공정상에서 막 표면에 오염이 발생하는 문제이다. 일반적으로 막 오염은 활성 슬러지들이 막 표면에 퇴적되어서 일어나며 이로 인해 심각한 투과 유량의 감소를 야기하게 된다. 본 연구에서는 막 오염 저항성이 뛰어난 나노 입자를 분리막 표면에 함침시켜 MBR 막을 제작하였으며 이 입자들은 막 표면에서 활성 슬러지들이 쉽게 달라 붙지 못하는 역할을 수행하게 된다. 즉, 뛰어난 투수량을 지닌 정밀여과막에 나노 입자를 첨가함으로서 실제 MBR 공정에서 막 오염을 저감시킴으로서 투수량을 보전할 수 있게 하였다. 이들을 이용하여 MBR 공정에서 막 오염이 휠씬 적게 일어나는 것을 확인하였으며 이를 바탕으로 현장에 적용하여 막 오염 저항성을 확인하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권2호
• /
• pp.179-184
• /
• 2016

In recent years, the on-resistance, power loss and cell density of Si power devices have not exhibited significant improvements, and performance is approaching the material limits. GaN is considered an attractive material for future high-power applications because of the wide band-gap, large breakdown field, high electron mobility, high switching speed and low on-resistance. Here we report on the Ohmic contact resistance and reverse-bias characteristics of AlGaN/GaN Schottky barrier diodes with and without annealing. Annealing in oxygen at $500^{\circ}C$ resulted in an increase in the breakdown voltage from 641 to 1,172 V for devices with an anode-cathode separation of $20{\mu}m$. However, these annealing conditions also resulted in an increase in the contact resistance of $0.183{\Omega}-mm$, which is attributed to oxidation of the metal contacts. Auger electron spectroscopy revealed diffusion of oxygen and Au into the AlGaN and GaN layers following annealing. The improved reverse-bias characteristics following annealing in oxygen are attributed to passivation of dangling bonds and plasma damage due to interactions between oxygen and GaN/AlGaN. Thermal annealing is therefore useful during the fabrication of high-voltage GaN devices, but the effects on the Ohmic contact resistance should be considered.