• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 춘계학술대회 논문집
• /
• pp.273-276
• /
• 1996

Polyphenylenediamine(PPD) film was prepared with dimethylsulfoxide after the synthesis of PPD by chemical polymerization. The molecular structure of conductive polymer synthesized were discussed by using SEM, FT-IR, NMR. The electrical conductivity measurements were carried out at room temperature. The electrical conductivity which was obtained from electrical instrument was 1.98${\times}$10$\^$-2/ S/cm at ambient temperature.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.836-837
• /
• 2006

A CCT diagram for Cr-Mo prealloyed sintered steels suitable for sinter hardening was established by combining dilatometry data, microstructural studies and microhardness measurements of the material. CCT diagrams deepen the understanding of material properties after sinter hardening and support the design of materials on an industrial scale by providing information about required cooling rates for successful sinter hardening of these materials.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.447-450
• /
• 1997

Temperature distribution measurements in the mockup apparatus of reactor vessel were performed to determine the effective thermal conductivity of Al powder porous media where stainless steel tubes were installed with different geometry. The temperature distributions at four separated sections with different arrangements of porous media have different slopes according to the geometrical configuration. From the measured temperature distribution, effective thermal conductivity have been derived using the least square fitting method.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1994년도 춘계학술대회 논문집
• /
• pp.50-56
• /
• 1994

Partial discharge on organic insulation surfaces are an important sauce of aging. Furthermore the modern PD measurement technigues are rapid developed as quality control and diagnostic tests to determine the fitness for use of HV equipment employing sol id electrical insulation. This paper deals with theory of conventional PD measurement and new tendency of technical development on PD measurements und evaluations. Finally the Measuring system used for diagnosing the surface aging on the organic insulation at High Voltage Laboratory of Technical University of Darmstadt in Germany is presented.

• 한국의류학회지
• /
• 제35권11호
• /
• pp.1362-1376
• /
• 2011

This study examines the effect of the structural properties of F/W wool knit fabrics for woman's knitwear on the perceptions of textures and sensible images of consumers and present basic data for textile designing by analyzing the relationship among the structural properties, mechanical properties, objective hand measurements and preferences. A total of 12 kinds of knit fabrics were prepared and investigated in terms of the differences in the subjective, mechanical properties and objective hand measurements according to the structural properties of knit fabrics. The data were analyzed by t-test. The subjective hand attributes of wool knits through factor analysis are categorized into 6 factors. In particular, the 'active/comfort' factor is a meaningful result that reflects the unique characteristics of knit fabrics compared to woven fabrics. Mechanical properties and objective hand measurements have a greater effect on textures than on sensible images; in addition, the structural properties, 'gauge' was the most important factor to influence the subjective evaluation.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.25.2-25.2
• /
• 2009

Vertically aligned zinc oxide(ZnO) nanorods (NRs) with different surface morphology were grown by metal organic chemical vapor deposition (MOCVD) on sapphire substrate with different deposition condition. Based on the surface morphology, ZnO nanostructures are divided into three types: nanoneedles, nanonails and nanorods with rounded tip. Variable temperature photoluminescence (PL) have employed to probe the exciton recombination in high density and vertically aligned ZnO Nanorod arrays. Low temperature photoluminescence measurements do not show any significant yellow emission, but the near band edge excitonic emission shows very strong dependence with the surface morphology. The recombination properties are expected to be different due to different surface-to-volume ratio and distribution of potential fluctuations of intrinsic defects.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1463-1466
• /
• 2007

Visco-elastic damping material for reducing heavy-weight floor impact noise and vibration in reinforced concrete structures was tested according to its thickness in the damping layer. The effect of damping material was compared with 20, 15, 10 and 5mm thickness. The wave propagation characteristics was measured for suggestion of an efficient method to reduce the floor impact noise. The method was proposed using the flexural wave propagation characteristics. The result showed that reduction of the thickness of damping layer made a slight difference; the natural frequency moved to higher frequency and the amplitude increased at low frequencies with 5mm thickness of damping material.

• The Korean Journal of Ceramics
• /
• 제4권2호
• /
• pp.114-121
• /
• 1998

Using Hebb-Wagner's asymmetric cell, partial conductivities of holes and electrons in yttria stabilized zirconia doped with 10 mol% TiO2 have been estimated by a dc polarization measurement. The current interrruption method and ac impedance measurements have been also made to evaluate the ionic conductivity and to examine the consistency of the partial conductivities. Partial conductivities of electrons(σn) and holes (σp) were found to be pro-peortional to -1/4 and 1/4 power of partial pressure of oxygen gas, respectively, except for σn at reducing conditions. In comparison with 5 mol% doped YSZ, σn was found to increase with the increase of TiO2 concentration, but σp stayed at almost a constant value.

• International Journal of Precision Engineering and Manufacturing
• /
• 제8권4호
• /
• pp.45-49
• /
• 2007

When drilling using electrical-discharge machining (EDM), severe electrode wear makes in-process measurements of the depth of the drilled hole and the volume of material removed impossible. To estimate the volume of material removed a reliable real-time discharge pulse counting method is proposed by assuming that the volume removed in EDM is proportional to the number of discharge pulses from an iso-energy pulse generator. The geometry of machined holes, including depths and cross-sectional profiles, is estimated using geometric analysis. A proportional relationship between the volume of material removed and the number of discharge pulses was developed and verified by experiments.

• Structural Engineering and Mechanics
• /
• 제16권2호
• /
• pp.115-126
• /
• 2003

A novel finite element model based on the incremental endochronic theory with the effect of temperature was developed in this study to explore the deformed behaviors of a flexible pavement material. Three mesh systems and two loading steps were used in the calculation process for a specimen of three-dimensional circular cylinder. Computational results in the case of an uni-axial compression test for temperatures at $20^{\circ}C$ and at $40^{\circ}C$ were compared with available experimental measurements to verify the ability of developing numerical scheme. The isotropic response and the deviatoric response due to the thermal effect were presented from deformations in different profiles and displacement plots for the entire specimen. The characteristics of changing asphalt concrete material under a specified loading condition might be seen clearly from the numerical results, and might provide an useful information in the field of road engineering.