• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.456-456
• /
• 2009

Boron doping on an n-type Si wafer is requisite process for IBC (Interdigitated Back Contact) solar cells. Fiber laser annealing is one of boron doping methods. For the boron doping, uniformly coated or deposited film is highly required. Plasma enhanced chemical vapor deposition (PECVD) method provides a uniform dopant film or layer which can facilitate doping. Because amorphous silicon layer absorption range for the wavelength of fiber laser does not match well for the direct annealing. In this study, to enhance thermal affection on the existing p-a-Si:H layer, a ${\mu}c$-Si:H intrinsic layer was deposited on the p-a-Si:H layer additionally by PECVD. To improve heat transfer rate to the amorphous silicon layer, and as heating both sides and protecting boron eliminating from the amorphous silicon layer. For p-a-Si:H layer with the ratio of $SiH_4$ : $B_2H_6$ : $H_2$ = 30 : 30 : 120, at $200^{\circ}C$, 50 W, 0.2 Torr for 30 minutes, and for ${\mu}c$-Si:H intrinsic layer, $SiH_4$ : $H_2$ = 10 : 300, at $200^{\circ}C$, 30 W, 0.5 Torr for 60 minutes, 2 cm $\times$ 2 cm size wafers were used. In consequence of comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 20 ~ 27 % of power, 150 ~ 160 kHz, 20 ~ 50 mm/s of marking speed, and $10\;{\sim}\;50 {\mu}m$ spacing with continuous wave mode of scanner lens showed the correlation between lifetime and sheet resistance as $100\;{\Omega}/sq$ and $11.8\;{\mu}s$ vs. $17\;{\Omega}/sq$ and $8.2\;{\mu}s$. Comparing to the singly deposited p-a-Si:H layer case, the additional ${\mu}c$-Si:H layer for doping resulted in no trade-offs, but showed slight improvement of both lifetime and sheet resistance, however sheet resistance might be confined by the additional intrinsic layer. This might come from the ineffective crystallization of amorphous silicon layer. For the additional layer case, lifetime and sheet resistance were measured as $84.8\;{\Omega}/sq$ and $11.09\;{\mu}s$ vs. $79.8\;{\Omega}/sq$ and $11.93\;{\mu}s$. The co-existence of $n^+$layeronthesamesurfaceandeliminating the laser damage should be taken into account for an IBC solar cell structure. Heavily doped uniform boron layer by fiber laser brings not only basic and essential conditions for the beginning step of IBC solar cell fabrication processes, but also the controllable doping concentration and depth that can be established according to the deposition conditions of layers.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.30 no.2
• /
• pp.118-123
• /
• 2019

Background and Objectives Voice evaluation is classified into subjective tests such as auditory perception and self-measurement, and objective tests such as acoustic and aerodynamic analysis. When evaluating dysphonia, subjective and objective test results do not always match. The purpose of this study was to analyze the relationship between subjective and objective evaluation in patients with dysphonia and to identify meaningful parameters by disease. Materials and Method The total of 322 patients who visited voice clinic from May 2017 to May 2018 were included in this study. Laryngeal lesions were identified using stroboscopy. Pearson correlation test was performed to analyse correlation between subjective tests including GRBAS scale and voice handicap index, and objective tests including jitter, shimmer, noise to harmonic ratio (NHR), cepstral peak prominence (CPP), maximal phonation time (MPT), mean flow rate, and subglottic pressure. Results In vocal nodule and sulcus vocalis, among GRBAS system, grade and breathiness showed good correlation with CPP, and roughness showed good correlation with jitter or shimmer. In unilateral vocal cord paralysis (UVCP), grade and breathiness showed a very good correlation with CPP, and also good correlation with jitter, shimmer, NHR, and MPT. Also asthenia showed good correlation with CPP and MPT. Vocal polyp has a limited association with other diseases. Conclusion In patients with dysphonia, grade and breathiness showed good correlation with CPP, jitter, and shimmer, and reflect the state of voice change well especially in UVCP, CPP, and MPT.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.04a
• /
• pp.85-92
• /
• 2002

When the United Nation classified as Korea is the one of the water deficit country. The consensus was made that the water is the one of the precious national resources. Government increases their R/D budget trying to get more clean water bodies. For instances, 'Sustainable Water Resources Development' project is the one of major title in '21 Century Frontier Research project and there are several small research projects are undergoing by the Ministry of Agriculture and KARICO. However, when the environmental preservation issue has been get more emphasis, construction of the Surface Dam met the blockage from the environmentalists due to the problem of the their water buried area. Since the most fitting site for surface dam had been used in the past, some engineer move their focus on modification of the existing Dam's height to enlarge its capacity or dredging the bottom of the reservoir recently However dredging evoke water quality problem in return by accumulated materials at the bottom. Last year the Dong Gang Dam plan has been canceled by environmental problem in water buried area of the reservoir. With the point of this view, ground water gets more focus for the one of the useful alternative for clean water bodies. Underground dam technique which had widely applied once in the early nineteen eighties by the KARICO and attenuated due to engineering insufficiency. The technique is newly studied with the advanced engineering technique. Still groundwater usage rate in Korea is much lower comparing with the advanced countries and has many rooms to develop. Wells, under ground dam and radial collector wells are typical facilities up to now. There is little application in Korea for the Recharge Dam, which had been widely used in the advanced countries. The Recharge Dam is technique to conjunct surface water and groundwater body together, This technique had developed to increase groundwater recharge at the beginning This research is the result of the study on the possibility of the development of the new technology, Groundwater Reservoir' which was modified from Recharge Dam. Groundwater Reservoir is like a deep artificial lakes trenched in hard rock aquifer to get groundwater. The advantage of the Groundwater Reservoir is followings 1) It can be developed at the plains area, not in the deep valley 2) Huge water body can be developed without dam 3) Small buried area comparing surface water dam makes the least environmental effect. 4) Trenching cost can be substitute by the income of the selling rock debris 5) Outfit of the reservoir can be modified to match with the site prospect 6) Rock debris can be used as constructing materials 7) It can be used as groundwater recharge system when the heavy rains comes 8) The reservoir looks like scenery lake with huge clean water bodies.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.4
• /
• pp.1-11
• /
• 2003

In order to measure aperture variation dependent on normal stress and to characterize on relationship between aperture variation and hydraulic conductivity this study measured apertures of rock fractures under a high resolution confocal laser scanning microscope (CLSM) with application of five stages of uniaxial normal stresses. From this method the response of aperture can be continuously characterized on one specimen by different loads of normal stress. The results of measurements showed a rough geometry of fracture bearing non-uniform aperture. They also revealed different values of aperture variations according to the load stages on each position along a fracture due to the fracture roughness. Laboratory permeability tests were also conducted to evaluate the changes of permeability coefficients related to the aperture variations by different loads. The results of permeability tests revealed that the hydraulic conductivity was not reduced at a fixed rate with increase of normal load. Moreover, the rates of aperture variations did not match to those of hydraulic conductivity. The hydraulic conductivity calculated in this study did not follow the cubic law, representing that the parallel plate model is not suitable to express the fracture geometry corresponding to the results of aperture measurements under the CLSM.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.5
• /
• pp.661-671
• /
• 2006

Steers (n = 335) of known genetic backgrounds from four fundamentally different growth types were subjected to two production systems to study the main effects and possible interactive effects on carcass composition. Growth types were animals with genetic potential for large mature weight (LL), intermediate mature weight-late maturing (IL), intermediate mature weight-early maturing (IE), and small mature weight-early maturing (SE). Each year, in a nine year study, calves of each growth type were weaned and five steers of each growth type were developed on pasture or feedlot and harvested at approximately 20 and 14 mo of age, respectively. Data recorded were chilled carcass weight and percentages of forequarter, foreshank, chuck, rib, plate, brisket, hindquarter, round, rump, shortloin, sirloin, flank, lean, fat, bone, and retail cuts. The growth $type{\times}production$ system interaction was an important source of variation in chilled carcass weight (p = 0.0395) and percentage retail cuts (p = 0.001), lean (p = 0.001), fat (p = 0.001), rump (p = 0.0454), shortloin (p = 0.0487), and flank (p = 0.001). The ranking of the growth $type{\times}production$ system means for percentage lean was LL-pasture>IL-pasture = IE-pasture = SE-pasture>LL-feedlot, IL-feedlot>IE-feedlot = SE-feedlot. The growth $type{\times}production$ system interaction was non-significant (p>0.05) for forequarter, foreshank, chuck, rib, plate, brisket, hindquarter, round and bone. Growth types of IE and SE yielded greater (p<0.05) mean forequarter than did growth types of IL and LL ($51.6{\pm}0.3$ and $51.5{\pm}0.3$ vs. $51.1{\pm}0.3$ and $50.8{\pm}0.3%$). Mean bone was highest (p<0.05) for the LL growth type and lowest (p<0.05) for the SE growth type ($19.5{\pm}0.5$ vs. $16.8{\pm}0.5%$). Mean bone was greater (p<0.05) for the pastured steers than for the feedlot steers ($21.8{\pm}0.8$ vs. $14.5{\pm}0.6%$). These data indicate that growth type responded differently in the two production systems and that these results should be helpful in the match of genetics to production resources.

• Journal of KIISE:Information Networking
• /
• v.34 no.3
• /
• pp.203-217
• /
• 2007

In this paper, a performance evaluation model of Networks with the multiple-buffered crossbar switches is proposed and examined. Buffered switch technique is well known to solve the data collision problem of the switch networks. The characteristic of a network with crossbar switches is determined by both the connection pattern of the switches and the limitation of data flow in a each switch. In this thesis, the evaluation models of three different networks : Multistage interconnection network, Fat-tree network, and other ordinary communication network are developed. The proposed evaluation model is developed by investigating the transfer patterns of data packets in a switch with output-buffers. Two important parameters of the network performance, throughput and delay, are evaluated. The proposed model takes simple and primitive switch networks, i.e., no flow control and drop packet, to demonstrate analysis procedures clearly. It, however, can not only be applied to any other complicate modern switch networks that have intelligent flow control but also estimate the performance of any size networks with multiple-buffered switches. To validate the proposed analysis model, the simulation is carried out on the various sizes of networks that uses the multiple buffered crossbar switches. It is shown that both the analysis and the simulation results match closely. It is also observed that the increasing rate of Normalized Throughput is reduced and the Network Delay is getting bigger as the buffer size increased.

• Journal of Korean Neurosurgical Society
• /
• v.63 no.2
• /
• pp.237-247
• /
• 2020

Objective : Fixation of the C1-2 segment is challenging because of the complex anatomy in the region and the need for a high degree of accuracy to avoid complications. Preoperative 3D-computed tomography (CT) scans can help reduce the risk of complications in the vertebral artery, spinal cord, and nerve roots. However, the patient may be susceptible to injury if the patient's anatomy does not match the preoperative CT scans. The intraoperative 3D image-based navigation systems have reduced complications in instrument-assisted techniques due to greater accuracy. This study aimed to compare the radiologic outcomes of C1-2 fusion surgery between intraoperative CT image-guided operation and fluoroscopy-guided operation. Methods : We retrospectively reviewed the radiologic images of 34 patients who underwent C1-2 fusion spine surgery from January 2009 to November 2018 at our hospital. We assessed 17 cases each of degenerative cervical disease and trauma in a study population of 18 males and 16 females. The mean age was 54.8 years. A total of 139 screws were used and the surgical procedures included 68 screws in the C1 lateral mass, 58 screws in C2 pedicle, nine screws in C2 lamina and C2 pars screws, four lateral mass screws in sub-axial level. Of the 34 patients, 19 patients underwent screw insertion using intraoperative mobile CT. Other patients underwent atlantoaxial fusion with a standard fluoroscopy-guided device. Results : A total of 139 screws were correctly positioned. We analyzed the positions of 135 screws except for the four screws that performed the lateral mass screws in C3 vertebra. Minor screw penetration was observed in seven cases (5.2%), and major pedicle screw penetration was observed in three cases (2.2%). In one case, the malposition of a C2 pedicle screw was confirmed, which was subsequently corrected. There were no complications regarding vertebral artery injury or onset of new neurologic deficits. The screw malposition rate was lower (5.3%) in patients who underwent intraoperative CT-based navigation than that for fluoroscopy-guided cases (10.2%). And we confirmed that the operation time can be significantly reduced by surgery using intraoperative O-arm device. Conclusion : Spinal navigation using intraoperative cone-beam CT scans is reliable for posterior fixation in unstable C1-2 pathologies and can be reduced the operative time.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.2
• /
• pp.50-61
• /
• 1995

A time scale modification method yielding rate-modified speech while conserving the characteristic of speech was implemented in real-time using a goneral purpose digital signal processor. Time scale modification changed pronunciation speed only, producing a time difference between the input signal and the modified signal, making it impossible to implement it in real-time. In this thesis, a system was implemented to remove the time difference between the input and modified signals. Speech signals slowed down or speeded up by a physical time scale modification method, such as adjusting the motor speed of the cassett tape recorder, was used as the input signal. Physical modification that controled only the inter speed of the cassette tape player distorted the pitch period of the original speech. In this study, a real-time system was implemented so that the pitch-distorted speech was reconstructed back to the original by fractional sampling pitch shifting using an FIR filter, and this signal was time scale modified to match the cassette tape recorder motor speed using SOLA time-scale medification. In experiments using speech signals medifiedby the proposed method, results obtained using a 16-bit resolution ADSP2101 processor and using computer simulations employing floating point operations showed about the same average frame signal-to-noise ratio of about 20 dB.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.2
• /
• pp.23-34
• /
• 2014

Though a dozen of different software life cycle models are suggested, there is no universal model which can satisfy all the characteristics of software. Organizations mix and match different life cycle models to develop a model more tailored for their systems and capabilities. We suggest overlapped-concurrent development life cycle model that is more suitable in various software development environment. Firstly, we divided the development process into abstract and implementation stage. Abstract stage is from software concept phase to detailed design starting time, and implementation stage is from detailed design phase to system testing phase. Next, the abstract stage introduced the overlapped phase concept that begins the next phase when the step is completed 20% by applying pareto's law. In the implementation stage, we introduced the concurrent development which the several phases are performed some time as when one use-case (UC) is completed the next development phase is started immediately. The proposed model has an advantage that it can reduce the inefficiency of development resource greatly. This model can increase the customer satisfaction with a great product at a low cost and on a short schedule. Also, this model can contribute to increase the software development success rate.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.6
• /
• pp.545-553
• /
• 1991

To find out the basic data for the possibility of agricultural utilization for GSA (Glutamine Synthetase Activity), the effect of nitrogen on the GSA in wheat leaf discs, the variation of GSA after light treatment and the comparative activity of GS during preservation were studied. The result of this study suggested that GSA could play an important and direct regulatory role in the nitrogen assimilation by wheat. During the growth stage of wheat its integral activity was found to closely match the organic nitrogen content. GS may therefore be the rate limiting enzyme in inorganic N assimilation. Moreover, integral GSA was closely correlated with grain yield and grain nitrogen. GSA could be suitable to utilize as a parameter for super type selection and an indicator for optimum nitrogen fertilization. Throughout the experiment, the contents of NO; were increased by N fertilization so that the NO; content was not attributable to change in the level of GSA. At investigation during dark-light transition of culture, no change in the level of GSA was observed until after 8-14 hours in the light treatment. And the level of GSA in wheat leaf discs during preservation at refrigerated storage $(-20^{\circ}C)$ was stable until 12 weeks, when its leaf discs were sampled with liquid nitrogen.