• The Journal of Advanced Prosthodontics
• /
• v.10 no.5
• /
• pp.367-373
• /
• 2018

PURPOSE. To evaluate the fit of a crown produced based on a 3D printed model and to investigate its clinical applicability. MATERIALS AND METHODS. A master die was fabricated with epoxy. Stone dies were fabricated from conventional impressions (Conventional stone die group: CS, n=10). Digital virtual dies were fabricated by making digital impressions (Digital Virtual die group: VD, n=10). 3D data obtained from the digital impression was used to fabricate 3D printed models (DLP die group: DD, n=10, PolyJet die group: PD, n=10). A total of 40 crowns were fabricated with a milling machine, based on CS, VD, DD and PD. The inner surface of all crowns was superimposed with the master die files by the "Best-fit alignment" method using the analysis software. One-way and 2-way ANOVA were performed to identify significant differences among the groups and areas and their interactive effects (${\alpha}=.05$). Tukey's HSD was used for post-hoc analysis. RESULTS. One-way ANOVA results revealed a significantly higher RMS value in the 3D printed models (DD and PD) than in the CS and DV. The RMS values of PD were the largest among the four groups. Statistically significant differences among groups (P<.001) and between areas (P<.001) were further revealed by 2-way ANOVA. CONCLUSION. Although the fit of crowns fabricated based on the 3D printed models (DD and PD) was inferior to that of crowns prepared with CS and DV, the values of all four groups were within the clinically acceptable range (<$120{\mu}m$).

• Korean Journal of Adult Nursing
• /
• v.27 no.5
• /
• pp.527-536
• /
• 2015

Purpose: The purpose of this study was to analyze the trend of nursing theories by Korean Journal of Adult Nursing (KJAN) for the last five years and to provide future directions for improvement. Methods: The study analyzed data collected from 323 research papers published in KJAN between 2010~2014. Descriptive analysis was conducted with a focus on frequency and percentage for the quantitative analysis. Qualitative analysis was performed for the analysis of nursing theories. Results: As for research topics, the analysis results based on the meta-paradigm of nursing show that the most frequent factors of analysis were adult patients in the area of human beings, hospitals in the area of environment, depression, anxiety, and suicide in the area of health, and all the influential factors in the area of nursing. The analysis results of uses of nursing theories in the papers reveal that only 4(1.2%) out of total 323 papers used the nursing theories, which indicates that the linkage and utilization of nursing theories in the published papers for the last five years were poor. Conclusion: We needs to make efforts at the society level to activate nursing theory utilization in research which is beloved to connect nursing practice, education, and research.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.4
• /
• pp.478-486
• /
• 2005

Statement of problem : Fracture and dimensional change of an acrylic resin denture are a rather common occurrence. Purpose : The purpose of this study was to compare differences in dimensional changes and flexural strength of separate maxillary complete dentures after immediate deflasking by injection molding and conventional compression processing. Material and method: To evaluate dimensional stability, the maxillary dentures were fabricated by using different materials and methods. Lucitone 199(Dentsply Trubyte. york, pennsylvania, USA) and Vertex(Dentimex, zeist, Netherlands) were used as materials. Compression and injection packing methods were used as processing methods. The impression surface of the dentures was measured by 3D Scann-ing System(PERCEPTRON USA) and overlapped original impression surface of the master cast. To evaluate flexural strength, resin specimens were made according to the different materials, powder/liquid ratio and processing methods. Flexural strength of the complete resin specimens (64mm$\times$10mm$\times$3.3mm) were measured by INSTRON 4467. (INSTRON, England) The data was analyzed by ANOVA, t-test and Tukey test. (p<.05 level of significance) Result: The results were as follows 1. There was no significant differences between master model and denture base for each group in overall dimensional changes. 2. Palatal area was more stable than flange or alveolar area in dimensional stability. but. there was no significant differences among each area. 3. Materials and power/liquid ratio had an effect on flexural strength. (P<.05) Especially materials was most effective. (P<.05) 4. Lucitone 199(powder/liquid ratio followed by manufacturer's direction) showed higher flexural strength than Vertex. Conclusion : Dimensional stability or flexural strength are affected by materials rather than packing techniques.

• KIEAE Journal
• /
• v.17 no.3
• /
• pp.125-131
• /
• 2017

Purpose: The study is to measure concentrations of indoor air pollutants in housing and to analyze the characteristics of pollutants in housing indoor-air between summer and winter comparatively. The research result could be used as data for public health through indoor air quality management of existing housing and more as a reference for new housing. Method: It was investigated 24 middle class housings of metropolitan area in winter which have been built for the past 30 years. Concentration of HCHO, TVOC was investigated in living room at morning and night and concentration of $CO_2$ was investigated in living room and master bedroom at morning and night. SKT100-X5 was used for concentration of HCHO, TVOC and ZGm053UK for concentration of $CO_2$. The characteristics of HCHO, TVOC, $CO_2$ concentration in winter were analyzed and then the concentrations in winter were analyzed the concentrations in summer being preceding research comparatively. Result: Average concentration of TVOC in winter was 2.7 times more than that of TVOC in summer, average concentration of HCHO in winter was about 2.0 times more than that of HCHO in summer. Average concentration of $CO_2$ in the morning at living room in winter was 1.3 times more than that of $CO_2$ in summer. Average concentration of $CO_2$ in the morning at master bedroom in winter was 1.1 times more than that of $CO_2$ in summer. Average concentration of TVOC was 1.31 times more than that of HCHO and standard deviation of that was 1.73 times higher. Average concentration of $CO_2$ was almost nearly close or over to 1,000ppm being criteria of the Ministry of Environment.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.19 no.4
• /
• pp.451-456
• /
• 2009

In this paper, a virtual force is generated and fed back to the operator to make the teleoperation more reliable, which reflects the relationship between a slave robot and an uncertain remote environment as a form of an impedance. In general, for the teleoperation, the teleoperated mobile robot takes pictures of the remote environment and sends the visual information back to the operator over the Internet. Because of the limitations of communication bandwidth and narrow view-angles of camera, it is not possible to watch certain regions, for examples, the shadow and curved areas. To overcome this problem, a virtual force is generated according to both the distance between the obstacle and the robot and the approaching velocity of the obstacle w.r.t the collision vector based on the ultrasonic sensor data. This virtual force is transferred back to the master (two degrees of freedom joystick) over the Internet to enable a human operator to estimate the position of obstacle at the remote site. By holding this master, in spite of limited visual information, the operator can feel the spatial sense against the remote environment. It is demonstrated by experiments that this collision vector based haptic reflection improves the performance of teleoperated mobile robot significantly.

• Journal of Korean Society on Water Environment
• /
• v.36 no.5
• /
• pp.364-372
• /
• 2020

The "Master Plan for the Revitalization of Water in the Nakdong River" is designed for the fundamental improvement of water quality in the Nakdong River. The water quality and flow of the Nakdong River system tributaries was monitored in this study. Among the living environmental standard parameters of 195 rivers, BOD (Biochemical oxygen demand), T-P (Total phosphorus) and TOC (Total organic carbon) were assessed to analyze the water quality from 2012 to 2019. We examined the role of TOC. It was found that 12 rivers exceeded the water quality of the second grade (3.0 mg/L BOD standard, 0.1 mg/L T-P standard, 4.0 mg/L TOC standard) based on BOD and T-P concentrations: the Gumi stream, Gisegok stream, Yongha stream, Yongho stream, Changnyeong stream, Gajwa stream, Gwangok stream, Yeongsan stream, Toerae stream, Hwapo stream, Sangnam stream and Hogye stream. These rivers require strategies to improve the quality of the Nakdong River. Based on the ongoing project, it is possible to supplement the "Master Plan for the Revitalization of Water in the Nakdong River" and manage it after verifying it as a component of people's life and therefore used to establish water quality control measures.

• Journal of Digital Convergence
• /
• v.14 no.4
• /
• pp.259-265
• /
• 2016

In this paper, a remote control system capable of monitoring and controlling the temperature of a refrigerator in real time using the ZigBee communication technology is developed. The developed system provides 24-hour surveillance function including temperature maintenance and it is able to determine monitored data from a remote location and to change the setting of the temperature value. In case the value is out of the setting, it is designed for administrators to verify the problem and take action, sending alarms to management server and the emergency to a preset administrator via SMS. Applying this system to refrigerators storing commercial, medical, and experimental material, the real time status such as temperature and malfunction of refrigerator can be managed up to 16 SZM(Slave Zigbee Module) by only one MZM(Master Zigbee Module).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.4A
• /
• pp.377-384
• /
• 2006

According to fast VoIP technology development, more and more companies change voice network into IP based network among branch offices. IP PBX, which is deployed up to now, composed of IP phone and VoIP Gateway. Every telphone has replaced with If phone which support VoIP and VoIP gateway is installed in PBTN connection point to relay voice data. It can reduce the communication expense of International call, long distance call and call between a headquater and a trance because it uses internet line. In this paper, IP PBX is implemented that can distribute call using PBX network only usig personal terminal without Proxy Server. Depending on Role, terminal can be registered Master, Server and Client and it is verified in terms of performance and validation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.3
• /
• pp.18-25
• /
• 2006

In order to perform system requirements quickly and accurately, an automatic design program of solid rocket motors(SRM) structure designated as the 'ProDes software' has been developed and verified. from given system design criteria and constraints, it has the capabilities to design, analysis, simulation and drawing process to greatly reduce the over 'design cycle time' and manpower of a project. The conception of the program is modular, and calculations are performed step by step allowing parametric design studies and providing final selected design goal. Each configurations of SRM components and joint types composed of various master models is obtained from the data base module of the library. Between the design results of the ProDes software and those of the previous detail design of the established motor showed good agreements.

• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.569-573
• /
• 2014

We demonstrate a low-cost, superbly efficient way of etching for the nano-, and micro-sized pyramid patterns on (100)-oriented Si wafer surfaces for use as a patterned master. We show a way of producing functional optical films for the viewing angle direction brightness-enhancement of Lambertian LED (light emitting diode)/OLED (organic light emitting diode) planar lighting applications. An optimally formulated KOH (Potassium hydroxide) wet etching process enabled random-positioned, and random size-distributed (within a certain size range) pyramid patterns to be developed over the entire (100) silicon wafer substrates up to 8" and a simple replication process of master patterns onto the PC (poly-carbonate) and PMMA (poly-methyl methacrylate) films were performed. Haze ratio values were measured for several film samples exhibiting excellent values over 90% suitable for LED/OLED lighting purposes. Brightness was also improved by 13~14% toward the viewing angle direction. Computational simulations using LightTools$^{TM}$ were also carried out and turned out to be in strong agreement with experimental data. Finally, we could check the feasibility of fabricating low-cost, large area, high performance optical films for commercialization.