• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.955-960
• /
• 2012

We fabricated piezoelectric unimorph cantilever generators (UCG) using $Pb(Zr_{0.54}Ti_{0.46})O_3$ + 0.2 wt% $Cr_2O_3$ + 1.0 wt% $Nb_2O_5$ (PZCN) piezoelectric thick films, which were produced by a tape casting method. The PZCN thick films were tailored with same width and thickness but different lengths from 7.7 to 57.7 mm in order to evaluate optimized UCG for energy harvesting device applications. When the length of PZCN film was increased, the resonance frequency of UCG was slightly increased from 7 Hz to 8 Hz, which could be due to enlarged area of the highly stiff piezo-ceramic film. However, the output power was proportionally increased with the length of PZCT film and it reached 4.68 mW (1.221 $mW/cm^3$) when the film's length was 57.7 mm under 25 g of tip mass at 8 Hz, which is sufficient for micro-scale device applications.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.1
• /
• pp.69-78
• /
• 2011

In this study, an optimization method using multi-objective genetic algorithm(MOGA) has been proposed to develop a fuzzy control algorithm that can effectively control a smart tuned mass damper(TMD). A 76-story benchmark building subjected to wind load was selected as an example structure. The smart TMD consists of 100kN MR damper and the natural period of the smart TMD was tuned to the first mode natural period of the example structure. Damping force of MR damper is controlled to reduce the wind-induced responses of the example structure by a fuzzy logic controller. Two input variables of the fuzzy logic controller are the acceleration of 75th floor and the displacement of the smart TMD and the output variable is the command voltage sent to MR damper. Multi-objective genetic algorithm(NSGA-II) was used for optimization of the fuzzy logic controller and the acceleration of 75th story and the displacement of the smart TMD were used as objective function. After optimization, a series of fuzzy logic controllers which could appropriately reduce both wind responses of the building and smart TMD were obtained. Based on numerical results, it has been shown that the control performance of the smart TMD is much better than that of the passive TMD and it is even better than that of the sample active TMD in some cases.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.6
• /
• pp.648-655
• /
• 2014

This paper describes the continuing effort to develope a single acting free-piston Stirling engine/alternator combination for use of the household cogeneration. Free piston Stirling engines(FPSE) use variations of working gas pressure to drive mechanically unconstrained reciprocating elements. Stirling cycle free-piston engines are driven by the Stirling thermodynamic cycle which is characterized by an externally heated device containing working gas that is continuously re-used in a regenerative, reversible cycle. The ideal cycle is described by two isothermal process connected by two constant volume processes. Heat removed during the constant volume cooling process is internally transferred to the constant volume heating process by mutual use of a thermal storage medium called the regenerator. Since the ideal cycle is reversible, the ideal efficiency is that of Carnot. Free-piston Stirling engine is have no crank and rotating parts to generate lateral forces and require lubrication. The FPSE is typically comprised of two oscillating pistons contained in a common cylinder. The temperature difference across the displacer maintains the oscillations, and the FPSE operate at natural frequency of the mass-spring system. The power is generated from a linear alternator. The purpose of this paper is to describe the design process of the single acting free-piston Stirling engine/alternator. Electrical output of the single acting free-piston Stirling engine/alternator is about 0.95 kW.

• Journal of Biosystems Engineering
• /
• v.37 no.3
• /
• pp.155-165
• /
• 2012

This study was performed to offer the data for design of the seedling bed transfer equipment to make the automation of working process in a plant factory. The seedling bed transfer equipment pushing the seedling bed with bearing wheels on the rail for interconnecting each working process by a pneumatic cylinder was made and examined. The examined transfer force to push the seedling bed with a weight of 178.9 N by the pneumatic cylinder with length of 60 cm and section area of 5 $cm^2$ was measured by experiments. The examined transfer forces was compared with theoretical ones calculated by the theoretical formula derived from dynamic system analysis according to the number of the seedling bed and pushing speed of the pneumatic cylinder head at no load. The transfer function of the equipment with the input variable as the pushing speed $V_{h0}$(m/s) and the output variable as the transfer force f(t)(N) was represented as $F(s)=(V_{h0}/k)(s+B/M)/(s(s^2+Bs/M+1/(kM))$ where M(kg), k(m/N) and B(Ns/m) are the mass of the bed, the compression coefficient of the pneumatic cylinder and the dynamic friction coefficient between the seedling bed and the rail, respectively. The examined transfer force curves and the theoretical ones were represented similar wave forms as to use the theoretical formular to design the device for the seedling bed transfer. The condition of no vibration of the transfer force curve was $kB^2>4M$. The condition of transferring the bed by the repeatable impact and vibration force according to difference of transfer distance of the pneumatic cylinder head from that of the bed was as $Ce^{-\frac{3{\pi}D}{2\omega}}<-1$, where ${\omega}=\sqrt{\frac{1}{kM}-\frac{B^2}{4M^2}}$, $C=\{\frac{\frac{B}{2M}-\frac{1}{kB}}{\omega}\}$, $D=\frac{B}{2M}$. The examined mean peak transfer force represented 4 times of the stead state transfer force. Therefore it seemed that the transfer force of the pneumatic cylinder required for design of the push device was 4Bv where v is the pushing speed.

• Journal of Korea Technology Innovation Society
• /
• v.18 no.3
• /
• pp.468-491
• /
• 2015

The major objective of this research is to suggest the proactive strategy and management of public R&D for the active transfer of technology based on the influential factor analysis of technology transfer. This study identified influential factors which make the greatest impact on the success of public technology transfer and commercialization through three points of view-technology supplier's view, technology adopter's view and view of commercialization-which contribute to successful technology transfer and commercialization. The core influential variables for blocking technology transfer are identified such as additional technological development, search for technology adopter followed by mass production technology and testing of confidence. Technology adopter is to create new markets or expand existing markets through the superiority (innovation) of licensing technology, increasing the internal innovation capabilities and maximizing the impacts of technology. This research suggests two effective strategies for improving technology transfer such as technology planning and marketing in the view of technology license. The strategy of technology planning should be established and executed to meet both technology trends and adopter's needs. And strong patents should be secured in terms of licensing of technology. Also the technological performance should be evaluated at mid-term appraisal, confirming the needs of adopter and competitive advantage of technology and patent. In addition to this, the customized technology marketing strategy for different fields of applications is also required in order to improve the likelihood of technology transfer. If the performance of R&D organization could be evaluated by global technological competitiveness and spillover effects of commercialization rather than quantitative output, the flow of technology transfer and commercialization would be accelerated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.8
• /
• pp.1105-1111
• /
• 2010

The Korea Atomic Energy Research Institutes has been developing the SMART (System integrated Modular Advanced ReacTor), an environment-friendly nuclear reactor for the generation of electricity and to perform desalination. SMART reactors can be exposed to various external and internal loads caused by seismic and coolant flows. The CRDM(control rod drive mechanism), one of structures of the SMART, is a component which is adjusting inserting amount of a control rod, controlling output of reactor power and in an emergency situation, inserting a control rod to stop the reactor. The purpose of this research is performing the analysis of dynamic characteristic to ensure safety and integrity of structure of CRDM. This paper presents two FE-models, 3-D solid model and simplified Beam model of the CRDM in the coolant, and then compared the results of the dynamic characteristic about the two FE-models using a commercial Finite Element tool, ABAQUS CAE V6.8 and ANSYS V12. Beam 4 and beam 188 of simplified-model were also compared each other. And simplified model is updated for accuracy compare to 3-D solid.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.182-189
• /
• 2019

3D printing technology is changing the paradigm of consumer-oriented design in supplier-oriented mass production. 3D printing technology in construction is expected to be able to replace existing wet methods along with modular construction. Recently, a number of cases of building construction using 3D printing using mortar-based materials have been announced in many regions, including North America, Europe, and Asia. In this study, we developed a design support tool with a slicing function to output 3D modeling for architecture for a 3D printing machine. We analyzed the process and the function of slicing programs that are commercially available. Seven slicing functions required for the architectural field were derived by analyzing cases, expert reviews, and related literature. The derived functions were extended from the slicing functions to develop the design support tools. Detailed algorithms and processes need to be developed for future derived functions.

• Journal of Distribution Science
• /
• v.13 no.6
• /
• pp.71-78
• /
• 2015

Purpose - This study attempts to analyze whether or not there are characteristics among the top management of companies that promote corporate performance at venture companies. It investigates the characteristics of the human and social capital that are inherent in top management at a venture company and conducts an empirical analysis of hypotheses examining if these characteristics will affect utilization of the governmental R&D support system as well as affect the firm's initial success. Research design, data, and methodology - This study conducted theoretical and empirical research together to accomplish the goal of the study. The pilot study researched human capital and social capital as the independent variables; the governmental R&D support system as the parameter; and, the initial success as the dependent variable. The empirical study carried out research on the model, establishment of hypotheses, and the statistical treatment. A survey was conducted targeting top management of high-tech venture companies in Daedeok Innopolis; 500 questionnaires were distributed; and, 222 were collected. Results - The human and social capital inherent in top management at venture companies in the early stages of their existence become good evaluation data for those who are invested in similar resources. If top management includes strong human and social capital, access to external resources will be easier; these will have a positive influence on the selection of overnmental support systems; and, this proper support will also have a positive influence on the initial success of the venture company. The results revealed the following. First, it was found that when the educational level and functional background, (the top management human capital), are the output function, top management human capital had a significant influence on selection of governmental R&D support funds. Second, it was found that the internal social capital and external social capital, (the top management social capital), had a significant influence on selection of governmental R&D support tasks. Third, it was found that selection of the governmental R&D support tasks at the start of the venture company had a positive influence on the corporate financial performance such as sales, business profits, and the increase in workers; and, had a significant influence on nonfinancial performance such as market share, competitive position, product competitiveness, and the future product development. Conclusions - Selection of the governmental R&D support system is not recognized as part of the direct sales of a venture company in its early stages, but as it can reduce costs for technical development and helps significantly in creating test products and mass production, it has a positive influence on the company's financial performance and nonfinancial performance as a result. Therefore, companies should take great efforts to frequently be selected as a candidate in the governmental R&D support system, as it can help facilitate R&D that requires extensive funds. As a result, companies can expect effects such as job creation and patent applications and they can advance future product sales.

• Korean Journal of Ecology and Environment
• /
• v.38 no.1 s.110
• /
• pp.118-127
• /
• 2005

The comparison of water balance and nutrient loading from paddy field with different irrigation management were carried out during 1999 ${\sim}$ 2002 at two different sites; one is irrigated with groundwater and the other is irrigated with surface water. For the surface water irrigated paddy field, irrigation was performed continuously during growing season. Whereas, initial irrigation with groundwater was applied during initial growing season, and the ponded water depth was maintained by natural precipitation since initial irrigation. The runoff frequency of groundwater irrigated paddy field was less than that of surface water irrigated paddy field. The nutrient concentration of ponded water was high by fertilization at early cultural periods, so reducing surface drainage during fertilization period can reduce nutrient loading from paddy fields. Amount of irrigation water to surface water irrigated paddy field was higher than to groundwater irrigated paddy field and evapotranspiration was similar because it is influenced by climate. Overall input in and output from paddy field irrigated with goundwater were less than that with surface water. This study indicate that efficient water management can reduce surface drainage outflow, save water, and protect water quality. It might be important BMPs for paddy field.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.2
• /
• pp.21-32
• /
• 2013

This is a preliminary study for the real-time feedback vibration control of building structures. The study developed a wireless acceleration sensor system based on authentic technology capacities, to integrate with the Prototype AMD system and ultimately construct the feedback vibration control system. These systems were used to evaluate the basic performance levels of the control systems within model building structures. For this purpose, the study first developed a wireless acceleration sensor unit that integrates an MEMS sensor device and bluetooth communication module. Also, the study developed an operating program that enables control output based on real-time acceleration response measurement and control law. Furthermore, the Prototype AMD and motor driver system were constructed to be maneuvered by the AC servo-motor. Eventually, all these compositions were used to evaluate the real-time feedback vibration control system of a 2-story model building, and qualitatively measure the extent of vibrational reduction of the target structure within the laboratory validation tests. As a result of the tests, there was a definite vibrational reduction effect within the laboratory validation tests. As a result of the tests, there was a definite vibrational reduction effect within 1st and 2nd resonance frequency as well as the random frequency of the model building structure. Ultimately, this study confirmed the potential of its wireless acceleration sensor system and AMD system as an effective tool that can be applied to the active vibration control of other structures.