• Applied Chemistry for Engineering
• /
• v.31 no.6
• /
• pp.639-645
• /
• 2020

Among the components of redox flow battery (RFB), the electrode serves as a diffusion layer of an electrolyte and a path for electrons and also is a major component that directly affects the RFB performance. In this paper, chloric/sulfuric mixed acidwas used as a supporting electrolyte in RFB system with Fe2+/Fe3+ and V2+/V3+ as redox couple. The optimum electrode and activation temperature were suggested by comparing the capacity, coulombic efficiency and energy efficiency according to the electrode type and activation temperature. In the RFB single cell evaluation using 5 types of carbon electrodes used in the experiments, all of them showed close to the theoretical capacity to retain the reliability of the evaluation results. GFD4EA showed relatively excellent energy efficiency and charge/discharge capacity. In order to investigate the electrochemical performance according to the activation temperature, GFD4EA electrode was activated by heat treatment at different temperatures of 400, 450, 500, 600 and 700 ℃ under an air atmosphere. Changes in physical properties before and after the activation were observed using electrode mass retention, scanning electron microscope (SEM), XPS analysis, and electrochemical performance was compared by conducting RFB single evaluation using electrodes activated at each temperature given above.

• The Journal of Engineering Geology
• /
• v.31 no.2
• /
• pp.149-163
• /
• 2021

Damage characteristics of granite, marble and sandstone whose properties were different were investigated by uniaxial compression test and cyclic loading-unloading test. Strength, elastic constants and damage threshold stresses were measured by uniaxial compression test and were compared with those measured by cyclic loading-unloading test. Average rock strengths measured by cyclic loading-unloading test were either lower than or similar with those measured by uniaxial compression test. Rocks with high strength and low porosity were more sensitive to fatigue than that with low strength and high porosity. Although permanent strains caused by cyclic loading-unloading were different according to rock types, they could be good indicators representing damage characteristics of rock. Damage threshold stress of granite and marble might be measured from stress-permanent strain curves. Acoustic emissions were measured during both tests and felicity ratios which represented damage characteristics of rocks were calculated. Felicity ratio of sandstone which was weak in strength and highly porous could not be calculated because of very few measurements of acoustic emissions. On the other hand, damage threshold could be predicted from felicity ratios of granite and marble which were brittle and low in porosity. The deformation behaviors and damage characteristics of rock mass could be investigated if additional tests for various rock types were performed.

• Journal of Powder Materials
• /
• v.28 no.6
• /
• pp.491-496
• /
• 2021

The process optimization of directed energy deposition (DED) has become imperative in the manufacture of reliable products. However, an energy-density-based approach without a sufficient powder feed rate hinders the attainment of an appropriate processing window for DED-processed materials. Optimizing the processing of DED-processed Ti-6Al- 4V alloys using energy per unit area (E_eff) and powder deposition density (PDD_eff) as parameters helps overcome this problem in the present work. The experimental results show a lack of fusion, complete melting, and overmelting regions, which can be differentiated using energy per unit mass as a measure. Moreover, the optimized processing window (E_eff = 44~47 J/mm² and PDD_eff = 0.002~0.0025 g/mm²) is located within the complete melting region. This result shows that the Eeff and PDDeff-based processing optimization methodology is effective for estimating the properties of DED-processed materials.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.35 no.6
• /
• pp.242-248
• /
• 2021

This study aims to compare nail-fold capillary blood velocity (CBV) according to the presence or absence of cold hypersensitivity in the hands (CHH) using nail-fold capillaroscopy under cold stress conditions. Eleven participants were taken from the cohort study for observing long-term health status of the faculty of Semyung university. Seven of the participants displayed CHH while four showed signs of non-CHH. CBV between 0 and 60 seconds (S1) and between 240 and 300 seconds (S2) was measured under cold stress for 5 minutes, respectively, and the average value was used to compare non-CHH group and CHH group. Body mass index, Nogung (PC8) temperature and temperature difference between Nogung (PC8) and Hyeopbaek (LU4) were significantly lower in CHH group compared to non-CHH group. The S2-S1 CBV difference was negatively correlated with PC8 temperature and PC8-LU4 temperature, and positively correlated with cold pattern score and cold hypersensitivity visual analog scale. The CHH group had a lower CBV overall than non-CHH group, and the S2-S1 CBV difference was significantly higher in the CHH group than in non-CHH group. This study suggests that CBV measured by nail-fold capillarosopy might be a useful indicator of cold hypersensitivity properties.

• Composites Research
• /
• v.35 no.3
• /
• pp.139-146
• /
• 2022

In this study, we study fabrication methods suitable for CNT fibers-based composite. We try to fabricate a composite material using a small amount of CNT fiber preparation of woven fabrics or stitched unidirectional fabrics consisting of CNT fiber is not achievable currently. The composite materials on the basis of CNT fibers have been mainly manufactured filament winding method due to productivity issues and difficulties in composite processes. We develop a new method to prepare CNT fibers-based composite using resin infiltrated CNT fibers-based films. Because CNT fibers have numerous nanopores inside, unnecessary resin can remain after curing and decrease the mechanical properties of the composites. To remove the excess resin, pressure should be applied during the process, but the pressure applied through VaRTM was not enough to remove the excess resin. To obtain the composite with high ratio of CNT fibers, higher pressure using hot press machine and foams next to the resin-infiltrated CNT fibers are necessary. We can obtain the composite having a mass ratio of 58.5 wt% based on the new suggested method and diluted epoxy. The specific strength of the composite reach 0.525 N/tex. This study presents a new process method that can be applied to the manufacturing of CNT fiber composite materials in the future.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.54-63
• /
• 2022

This paper is a study on the friction damper, which is one of the seismic reinforcement devices for structures. This study developed a damper by replacing the internal friction material with ultra high molecular weight polyethylene (UHMWPE), a type of composite material. In addition, this study applied a multi-friction method in which the internal structure where frictional force is generated is laminated in several layers. To verify the performance of the developed multi-friction damper, this study performed a characteristic analysis test for the basic physical properties, wear characteristics, and disc springs of the material. As a result of the wear test, the mass reduction rate of UHMWPE was 0.003%, which showed the best performance among the friction materials based on composite materials. Regarding the disc spring, this study secured the design basic data from the finite element analysis and experimental test results. Moreover, to confirm the quality stability of the developed multi-friction damper, this study performed an seismic load test on the damping device and the friction force change according to the torque value. The quality performance test result showed a linear frictional force change according to the torque value adjustment. As a result of the seismic load test, the allowable error of the friction damper was less than 15%, which is the standard required by the design standards, so it satisfies the requirements for seismic reinforcement devices.

• Journal of the Society of Disaster Information
• /
• v.19 no.3
• /
• pp.532-544
• /
• 2023

Purpose: To identify and evaluate the risk of chemical fire causative substances by using thermal analysis methods (DSC, TGA) for the hazards and physical property changes that occur when newly used biofuels are mixed with existing fuels It is to use it for identification and evaluation of the cause of fire by securing data related to the method and the hazards of the material according to it. Method: The research method used in this experiment is the differential scanning calorimeter (DSC: Difference in heat flux) through quantitative information on the caloric change from the location, shape, number, and area of peaks. flux) was measured, and the weight change caused by decomposition heat at a specific temperature was continuously measured by performing thermogravimetric analyzer (TGA: Thermo- gravimetric Analyzer). Result: First, in the heat flux graph, the boiling point of the material and the intrinsic characteristic value of the material or the energy required for decomposition can be checked. Second, as the content of biodiesel increased, many peaks were identified. Third, it was confirmed through analysis that substances with low expected boiling points were contained. Conclusion: It was shown that the physical risk of the material can be evaluated by using the risk of biodiesel, which is currently used as a new energy source, through various physical and chemical analysis techniques (DSC + TGA).In addition, it is expected that the comparison of differences between test methods and the accumulation and utilization of know-how on experiments in this study will be helpful in future studies on physical properties of hazardous materials and risk assessment of materials.

• Computers and Concrete
• /
• v.32 no.3
• /
• pp.247-261
• /
• 2023

Due to the non-uniform distribution of meso-structure, the diffusion of chloride ions in concrete show the characteristics of characteristics of randomness and fuzziness, which leads to the non-uniform distribution of chloride ions and the non-uniform corrosion of steel rebar in concrete. This phenomenon is supposed as the main reason causing the uncertainty of the bearing capacity deterioration of reinforced concrete structures. In order to analyze and predict the durability of reinforced concrete structures under chloride environment, the random features of chloride ions transport in concrete were studied in this research from in situ meso-structure of concrete. Based on X-ray CT technology, the spatial distribution of coarse aggregates and pores were recognized and extracted from a cylinder concrete specimen. In considering the influence of ITZ, the in situ mesostructure of concrete specimen was reconstructed to conduct a numerical simulation on the diffusion of chloride ions in concrete, which was verified through electronic microprobe technology. Then a stochastic study was performed to investigate the distribution of chloride ions concentration in space and time. The research indicates that the influence of coarse aggregate on chloride ions diffusion is the synthetic action of tortuosity and ITZ effect. The spatial distribution of coarse aggregates and pores is the main reason leading to the non-uniform distribution of chloride ions both in spatial and time scale. The chloride ions concentration under a certain time and the time under a certain concentration both satisfy the Lognormal distribution, which are accepted by Kolmogorov-Smirnov test and Chi-square test. This research provides an efficient method for obtain mass stochastic data from limited but representative samples, which lays a solid foundation for the investigation on the service properties of reinforced concrete structures.

• Applied Chemistry for Engineering
• /
• v.34 no.4
• /
• pp.357-364
• /
• 2023

Selective catalytic reduction (SCR) is the most effective method for reducing nitrogen oxide emissions, but the operating temperature range of V₂O₅-WO₃/TiO₂ catalysts is narrow (300~400℃). In this study, a new catalyst with an operating temperature range of 200~450℃ was developed. The catalyst poison, ammonium bisulfate, generated during the SCR process can be removed by heating above 350℃. To increase the number of active sites and promote the dispersion of active materials, titanium isopropoxide (TTIP) treatment was performed on the TiO₂ support with various TTIP/TiO₂ mass ratios. Among them, the 5 wt% TTIP loaded catalyst showed improved performance due to higher thermal stability caused by high W dispersion and the formation of V⁵⁺. In addition, the 5 wt% TTIP-loaded catalyst prepared by a one-step co-precipitation method showed greater V-OH and W-OH dispersion and enhanced interactions in contrast to conventional methods, resulting in higher catalytic activity at lower temperatures. This review article aims to provide an accessible explanation for researchers investigating how to improve the surface properties of TiO2 catalysts using TTIP.

• Proceedings of the SCSK Conference
• /
• 2003.09b
• /
• pp.26-31
• /
• 2003

Korean Ginseng is a medicinal herb which grows naturally in korea. an ancient country situated in north-eastern Asia. Its medical use was already well known to herb doctors in this region about five thousand years ago since the effectiveness of korean ginseng has been recognized through practical use for a long time. Korean Ginseng has always been regarded as a devine cure. The name "Ginseng" can be found in various medicinal books. many of which were written as early as B.C. 100. In the records of many chinese medical books. dating from the inception of publishing, it was noted that Korean Ginseng was of the highest level of quality. Korean Ginseng originally grew in the mountains of korea. However, this wild Korean Ginseng(js called SANSAM) could not meet the ever-increasing demands. and from the 16th century. it has been cultivated on farms for mass processing and supplying in korea(js called INSAM). It was already recognized in korea a long time ago(B.C. 57 - A.D. 668) that Korean Ginseng possessed the qualities of panacea, tonic and rejuvenator, and had other medicinal properties as well. The effectiveness of Korean Ginseng is widely recognized among south-eastern Asians as well as Chinese. As its effect has been proved scientifically. Korean Ginseng is now becoming the ginseng for all human beings in the world. Korean ginseng is differently called according to processing method. Dried thing is Insam(white ginseng), boiled or steamed is Hongsam(red ginseng). 장뇌삼(long headed ginseng) is artificially grown in the mountain no in field for a long time. So the body is thin and some long. but ingredients are concentrated. Korean wild ginseng(SANSAM) is rare in these days but we developed cosmetic ingredient. The scientific name of Korean Ginseng is Panax Ginseng. It has acknowledge as a natural mysterious cure among the notheastern peoples. because of its broad medicinal application. The origin of the word" Panax" derived from panacea. a Greek word meaning cure-all. According to the classification method of herb medicines in the Chinese medicinal book. "God-Farmer Materia Medica(A.D. 483-496) korean Ginseng was described as the superlative drug: panacea. tonic and rejuvenator. We studied skin immunological effect. collagen synthesis. cell growth and whitening effect of SANSAM extract. IN cosmetics.. SANSAM extract had skin fibroblast cell growth effect. recover damaged skin in the sun and protect fine wrinkle. Also. In hair product.. inhibits hairless, white hair.its hairless, white hair.