• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.79-89
• /
• 1995

Rattle noise occurs at manual transmission as idling and driving of a automotive. It can be solved by torsional characteristics of a clutch disc. A clutch disc consist of a region of pre-damper and main-damper. Rattle noise is affected by pre-damper and main-damper equipped for a torsional spring and friction washer. Pre-damper range covers noise radiating from manual transmission when engine is idling and main-damper range covers noise when engine is driving. The aim of this reserch is to clear transmission rattle noise by way of torsional characteristics of a clutch disc. The experiment is carried out as idling and driving of a automobile equipped for 1.5L MPI engine, dry single-disc type clutch and manual transmission. In this study, the results show for a vibration of manual transmission as idling and driving can be cleared by a clutch disc of Pre-damper type.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.372-378
• /
• 2016

Clutch torque control is the key to the ride comfort improvement of a vehicle equipped with AMT (automated manual transmission). For such control, the torque transfer starting point, known as the "kiss point," should be indicated or at least estimated to compensate for the clutch torque. The kiss point changes due to wear, high temperature, and fatigue; as such, it should be estimated while the vehicle is being driven. In this study, the method of kiss point active estimation for an AMT vehicle with a dry-type clutch was devised. The kiss point is learned while the engine is in an idle state and while the transmission is at a neutral gear position. It is determined when the input shaft of the transmission starts to rotate by slowly engaging the clutch. The noise of the shaft speed signal during the slow engagement process is filtered for accurate control. The kiss point estimation at various clutch engagement speeds was analyzed via a vehicle test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.122-129
• /
• 2015

Excessive overheating to a manual transmission clutch system under operating conditions can be considered the main reason of its performance degradation. The clutch system has to be ensured with its service life by showing that it passes the extreme tests called anti-fade test and hill start test in a certain design step. In general, design feedbacks from these kinds of the experiments are adapted to the system to enhance its performance. However, it usually takes much time and costs a lot due to the repetition of the tests. In this research, a process to calculate temperature of the clutch system was developed to determine whether the design can be passed the anti-fade test and hill start test in the design phase. The process incorporates many CAE techniques such as heat transfer analysis using 1D dynamic simulation method, system dynamics, CFD and parametric optimization. CFD is utilized to analyze 3-dimensional heat transfer of the clutch system and fluid dynamics of air in the clutch housing. The process was applied for the clutch systems in several vehicle models. The results was compared with those of the experiment. The applicability of the developed process was verified by comparing the predicted results with experimental results.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.3
• /
• pp.287-293
• /
• 2015

With the rise in oil prices and ongoing concerns about environment, there is an increased amount of interest in automated manual transmission (AMT) vehicles. Torque control in an AMT vehicle is attained by controlling the displacement of the dry-type clutch's actuator. To provide good ride comfort akin to that of an automatic transmission vehicle, the clutch control is vital to an AMT vehicle. In this study, a method of obtaining the clutch torque from a dynamometer test is devised. This method is able to identify the relationship between the displacement of the clutch actuator and the clutch torque. A simulator for estimating the performance of an AMT vehicle is developed using MATLAB Simulink. The results obtained from both the vehicle and simulation exhibit a similar trend.

• Journal of Power System Engineering
• /
• v.17 no.5
• /
• pp.128-137
• /
• 2013

Modern transmission technologies such as automated manual transmission(AMT) and dual clutch transmission(DCT) are interested to all manufactures due to their fuel efficiency and driver's convenience, especially in a hybrid system. AMT has advantages in that they have a high efficiency of manual transmissions(MT) and offer operation convenience similar to automatic transmissions(AT), but it has some disadvantages in that they have torque gap during gear shift and shift time. To reduce disadvantages, it is necessary to evaluate errors and characteristics as a developing simulation model before experimental verification. The purpose of this study is to develop virtual components and simulate the transient response of AMT. A dynamic AMT model and a control logic for an integrated vehicle model have been developed using Matlab/Simulink as a simulation platform. In this paper, the clutch model to describe the stick-slip transition mode and the transmission model to describe the neutral gear shifting is introduced and compared with each other.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.101-109
• /
• 2004

Three models with various degree-of-freedom for a manual transmission clutch full-size tester have been developed and the models' reliability and accuracy have been verified using the measured data. A simulation study has also been conducted to understand dynamic behavior of the tester. The model for this simulation study includes clutch disk friction and damper dynamics. The developed model is very accurate in terms of maximum torque exerted on the clutch, slip duration and the vibration response except a slight difference compared to the measured data. In a history graph of the clutch torque, the maximum torque response from simulation is flat but the measured is sunken with a noticeable curvature. This phenomenon is found to be irrelevant to the dynamics of the full-size tester but is originated from the characteristics of the clutch itself. Thus, the full-size tester has been proven to be a reliable tester for clutch's power and torque transmission capability. To obtain a better understanding of clutch's characteristics and relationship between full-size tester and other testing methodologies, future research directions have been suggested.

• Journal of Power System Engineering
• /
• v.14 no.6
• /
• pp.35-40
• /
• 2010

This article deals with the numerical analysis results of stiffness of diaphragm spring used in the clutch of a manual transmission. In order to investigate the relationship of the force and displacement in a diaphragm spring, we have established a numerical model of diaphragm spring using a well-known analytic model of Belleville spring and a cantilever beam model for the finger part of diaphragm spring. Using the stress and strain relations of Belleville spring and cantilever beam, we propose the analytic equation of motion of diaphragm spring for the use of a clutch automated actuator in an automated manual transmission. The proposed analytic model represents the typical dynamic characteristics of diaphragm spring along with the release bearing travel. And it is characterized in a closed-form equation, therefore it can be used for the further study of development of actuator and control law of clutch automating mechanism.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.3 s.180
• /
• pp.86-93
• /
• 2006

This study is concerned with the investigation of characteristics of an AMT (Automated Manual Transmission) which are composed of clutch part and transmission part. When a shilling signal is received from the controller, the clutch is disengaged first, and shifting action including selecting action is followed, and then the clutch is engaged last. The characteristics of transmission shifting response are affected by various parameters of clutch and transmission control elements. Analytical results are in fair agreement with experimental results. It is found that the operating pressure level is the most important for the response of AMT characteristics, and that the other parameters such as natural frequency and damping ratio of the control valve are less important.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.3849-3855
• /
• 2012

This paper describes a control algorithm and test results of an automated manual transmission clutch actuated by a stepping motor. The control algorithm extracts driver's demand from CAN signals and decides the exact timing to engage or disengage the clutch based on the demand. A pulse signal is generated to drive the clutch and the travel of the clutch can be calculated by accumulating the pulse signal. An auto code generation method was introduced in implementing the control logic to the micro-processor of the prototype controller and a series of basic tests were carried out to validate its performance.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.10
• /
• pp.75-82
• /
• 2007

The AMT(Automated Manual Transmission) has been developed by utilizing the auto clutch system and the automatic shift mechanism, to automate the clutch operation and shift operation of the existing MT(Manual Transmission). The use of hydraulic actuator for each actuator of the clutch and gear has realized a reduction of fuel consumption and exhaust emission. In this paper, we develop a simulator for the transmission control system of the AMT using AMESim. The developed simulator can be applied to design the hydraulic select actuator system of an AMT.