본 연구 목적은 선형가속기를 통해 입사된 전자가 표적(target)을 구성하는 물질과 두께에 따른 광자 특성을 평가하는 것이다. 전산모사 설계는 2 mm 두께의 텅스텐 단일물질과 1.8 mm 와 2.3 mm 두께의 텅스텐과 구리 복합물질로 구성된 선형가속기 표적(Target)이다. 연구 방법은 첫째, 표적 내 일차 입자의 거동은 전자플루언스와 전자 에너지 축적으로 평가하였다. 둘째, 표적 내에서 발생하는 광자는 광자 플루언스로 평가하였다. 셋째, 표적으로부터 1 m 거리에서의 광자 각-에너지 분포는 광자 플루언스로 평가하였다. 그 결과 첫째, 단일물질과 복합물질 표적에서의 전자 플루언스와 에너지 축적을 통해 일차 입자인 전자가 표적 밖으로 방출되지 않았으며, 표적 두께에 따라 전자가 음의 선형적으로 감쇄하였다. 둘째, 복합물질 표적이 단일물질 표적보다 광자 생성이 더 높은 것으로 나타났다. 이는 물질 구성 성분과 두께가 광자 생성에 영향을 준다는 사실을 확인하였다. 셋째, 차폐 해석에 필요한 각 분포에 따른 광자 플루언스를 계산하였다. 이러한 결과는 선형가속기 표적을 구성하는 물질과 두께에 따라 광자 생성률이 차이 나는 것을 확인할 수 있었다. 따라서, 본 연구는 국가에서 도입 중인 컨테이너 보안 검색용 선형가속기 사용시설의 설계 및 운영 시 필요한 자료이며, 방사선 방호에 기초 자료로 활용될 수 있을 것으로 생각된다.
본 연구 목적은 컨테이너 보안 검색용 선형가속기에서 발생하는 방사화 특성을 평가하는 것이다. 전산모사 설계는 첫째, 표적은 텅스텐(Z=74) 단일물질 표적 및 텅스텐(Z=74)과 구리(Z=29) 복합물질 표적으로 구성하였다. 둘째, 부채꼴(Fan beam) 조준기는 물질에 따라 납(Z=82) 단일 물질과 텅스텐(Z-74)과 납(Z=82)의 복합물질로 구성하였다. 셋째 선형가속기가 위치한 방(Room)의 콘크리트는 Magnetite type 및 불순물(Impurity)을 포함하였다. 연구 방법은 첫째, MCNP6 코드를 이용하여 선형가속기 및 구조물을 F4 Tally로 광중성자 플럭스(Flux)를 계산하였다. 둘째, MCNP6 코드에서 계산된 광중성자 플럭스를 FISPACT-II에 적용하여 방사화 생성물을 평가하였다. 셋째, 방사화 생성물의 비방사능을 통해 해체 평가를 진행하였다. 그 결과 첫째, 광중성자 분포는 표적에서 가장 높게 나왔으며, 조준기 및 10 cm 깊이의 콘크리트 순으로 나타났다. 둘째, 방사화 생성물은 텅스텐 표적 및 조준기에서 W-181, 불순물이 포함된 콘크리트에서 Co-60, Ni-63, Cs-134, Eu-152, Eu-154 핵종이 부산물(by-product)로 생성되었다. 셋째, 해체 시 텅스텐 표적은 90일 이후 자체 처분 허용 농도를 만족하는 것으로 보였다. 이러한 결과는 9 MeV 에너지에서의 광중성자 수율(Yield) 및 방사화 정도가 미미한 것으로 확인할 수 있었다. 하지만, 선형가속기 텅스텐 표적 및 조준기에서 발생한 W-181은 수리를 위한 분해 시 피폭의 영향을 줄 수 있을 것으로 생각된다. 따라서, 본 연구는 컨테이너 보안검색용 선형가속기 방사화된 부품관리에 관한 기초 자료를 제시한 것이다. 또한, 컨테이너 보안 검색용 선형 가속기 해체 시 자체처분을 만족하는 농도 기준을 입증하는데 활용될 수 있을 것으로 기대한다.
본 연구 목적은 선형가속기 표적(Target) 및 조준기(Collimator)에서 발생한 광중성자 특성을 평가하는 것이다. 전산모사 설계는 첫째, 표적은 단일물질 표적과 복합물질 표적으로 구성하였다. 둘째, 조준기 종류에 따라 원뿔형(Cone beam) 조준기와 부채꼴(Fan beam) 조준기로 구성하였다. 셋째, 부채꼴 조준기의 물질을 납(Pb)으로만 구성된 단일물질과 텅스텐(W)과 납으로 구성된 복합물질 조준기로 구성하였다. 연구 방법은 표적으로부터 100 cm 거리에서 가상의 구(Sphere) 표면에서 F2 Tally를 이용하여 광중성자 발생률과 에너지 스펙트럼을 계산하였다. 그 결과 광중성자 발생률은 첫째, 표적에 따라서는 20% 차이가 발생하였다. 둘째, 조준기의 종류에 따라서는 10% 차이가 발생하였다. 셋째, 조준기 물질에 따라서는 40% 차이가 발생하였다. 광중성자 스펙트럼에서도 평균 광중성자 플럭스(Flux)가 광중성자 발생량과 유사한 경향으로 나타났다. 이러한 결과로 9 MeV 선형가속기 광중성자 발생은 표적보다는 조준기에 의해 광중성자 발생이 증가하며, 조준기의 종류보다는 물질에 영향을 더 크게 받는 것을 확인할 수 있었다. 광중성자 발생이 적은 표적 및 조준기를 선택하여 운영하는 것이 가장 적극적인 방사선 방호가 될 것이다. 따라서, 본 연구는 컨테이너 보안 검색용 선형가속기 도입 및 운영 그리고 방사선 방호에 유용한 자료가 될 수 있을 것으로 생각된다.
Kwon, Na Hye;Jang, Young Jae;Kim, Dong Wook;Shin, Dong Oh;Kim, Kum Bae;Kim, Jin Sung;Choi, Sang Hyoun
한국의학물리학회지:의학물리
/
제31권4호
/
pp.194-204
/
2020
This study investigated and analyzed the Korean and international status of radioactive waste management for medical linear accelerators (linacs) and proceed prior research to suggest radiation safety regulations and guidelines for the safe use of radiation. We analyzed the number of linacs installed in the radiation oncology departments of 103 institutions. In addition, we analyzed the procedures and standards for disposal in Korea and foreign countries. For foreign countries, we analyzed the status based on reports from the United States, Japan, Europe, and Canada. A total of 182 linacs are installed in Korea and 95% of them use more than 10 MV of energy. In Korea, standards for managing radioactive waste from a linac, disposal procedures, and clearance criteria have yet to be established. Therefore, radioactive waste is disposed of in different ways depending on the hospitals where they originate. Japan, the US, and Canada have recommended clearance levels and procedures for linacs. Other countries have provided management guidelines for research or large-scale accelerators, but not for medical purposes. In this study, we investigated the management of radioactive waste from medical linacs in Korea and abroad. Several foreign countries have suggested a clearance level and criteria for disposing of waste storage drums. For the safe management of medical linacs, it is necessary to establish safety management regulations. In Korea, standards for disposal, such as radiation or dose limits, are required for medical linacs. A system for clearance when disposing at a medical institution should be created.
Choi, Sang Hyoun;Shin, Dong Oh;Shin, Jae-ik;Kwon, Na Hye;Ahn, So Hyun;Kim, Dong Wook
한국의학물리학회지:의학물리
/
제32권4호
/
pp.83-91
/
2021
Various types of high-precision radiotherapy, such as intensity-modulated radiation therapy (IMRT), tomotherapy (Tomo), and stereotactic body radiation therapy have been available since 1997. After being covered by insurance in 2015, the number of IMRT cases rapidly increased 18-fold from 2011 to 2018 in Korea. IMRT, which uses a high-beam irradiation monitor unit, requires higher shielding conditions than conventional radiation treatments. However, to date, research on the shielding of facilities using IMRT and the current understanding of its status are insufficient, and detailed safety regulation procedures have not been established. This study investigated the recommended criteria for the shielding evaluation of facilities using medical linear accelerators (LINACs), including 1) the current status of safety management regulations and systems in domestic and international facilities using medical LINACs and 2) the current status of the recommended standards for safety management in domestic and international facilities using medical LINACs. It is necessary to develop and introduce a safety management system for facilities using LINACs for clinical applications that is suitable for the domestic medical environment and corresponds to the safety management systems for LINACs used overseas.
Kwon, Na Hye;Shin, Dong Oh;Ann, So Hyun;Kim, Jin Sung;Choi, Sang Hyoun;Kim, Dong Wook
Nuclear Engineering and Technology
/
제54권2호
/
pp.449-455
/
2022
The rapid rise in the application of novel treatment techniques, such as intensity-modulated radiotherapy (IMRT), motivated us to survey the status of Korea's radiation safety management and the shielding designs of facilities employing medical linear accelerators (LINACs). To this end, a questionnaire was used to collect information on LINAC facilities and treatments, workload, shielding design, shielding management, and path of obtaining shielding information. Out of 100 domestic institutions, 52 responded to the survey. Approximately 70% of the institutions utilized IMRT for more than 60% of their cases, and an IMRT factor of 5 was adopted by 75% of these institutions. Over 80% of the institutions accounted for the applied time-averaged dose rate per week and instantaneous dose equivalent rates in their shielding designs. Approximately 45% of the institutions obtained important shielding information via a radiation shielding design company and the NCRP-151 report. Overall, most facilities were shown to follow the standards recommended by the relevant international agencies. However, the requirement to establish standardized shielding design information and clarify ambiguous paths for information acquisition was also highlighted. Therefore, the study's results can be used as a foundation for establishing a safety control system and for creating adequate shielding designs.
Dong-Hee Han ;Kyung-Hwan Jung;Jang-Oh Kim ;Da-Eun Kwon ;Ki-Yoon Lee;Chang-Ho Lee
Nuclear Engineering and Technology
/
제55권6호
/
pp.1994-1998
/
2023
This study quantitatively evaluated the source term of a linear accelerator according to target thickness for a 6-20 MeV electron beam using MCNP6. The elements of the target were tungsten and copper, and a composite target and single target were simulated by setting different thickness parameters depending on energy. The accumulation of energy generated through interaction with the collided target was evaluated at 0.1-mm intervals, and F6 tally was used. The results indicated that less than 3% reference error was maintained according to the MCNP recommendations. At 6, 8, 10, 15, 18, and 20 MeV, the energy accumulation peaks identified for each target were 0.3 mm in tungsten, 1.3 mm in copper, 1.5 mm in copper, 0.5 mm in tungsten, 0.5 mm in tungsten, and 0.5 mm in tungsten. For 8 and 10 MeV in a single target consisting only of copper, the movement of electrons was confirmed at the end of the target, and the proportion of escaped electrons was 0.00011% and 0.00181%, respectively.
L. Czap;I.J. Kim;J.I. Park;C.-Y. Yi;Y. Kim;Z. Msimang
Nuclear Engineering and Technology
/
제56권7호
/
pp.2698-2703
/
2024
A bilateral comparison was conducted between the International Atomic Energy Agency (IAEA) and the Korea Research Institute of Standards and Science (KRISS) to measure the absorbed dose to water in accelerator photon beams. KRISS served as a linking laboratory to compare the IAEA standard with the key comparison reference value (KCRV) of the BIPM.RI(I)-K6 program, in which KRISS participated in 2017. Two ionization chambers from the IAEA were used as transfer instruments for the comparison. Both laboratories measured the calibration coefficients of these instruments and calculated the ratios. The ratio of the KRISS standard to the KCRV was applied to obtain the degree of equivalence of the IAEA, along with its uncertainty. The largest deviation of the IAEA measurement from the KCRV was 3.4 mGy/Gy, significantly smaller than the expanded uncertainty of 10.7 mGy/Gy (k = 2, 95% level of confidence). This study demonstrates the equivalence of IAEA's measurement standard for accelerator photon beams to other primary standard dosimetry laboratories. It provides evidence for the satisfactory operation of IAEA's quality management system and enhances the international credibility of the IAEA SSDL network, particularly in high-energy accelerator photon beams from linear accelerators.
Kwon, Na Hye;Shin, Dong Oh;Kim, Jinsung;Yoo, Jaeryong;Park, Min Seok;Kim, Kum Bae;Kim, Dong Wook;Choi, Sang Hyoun
Nuclear Engineering and Technology
/
제54권2호
/
pp.507-513
/
2022
When X-ray energy above 8 MV is used, photoneutrons are generated by the photonuclear reaction, which activates the components of linear accelerator (linac). Safely managing the radioactive material, when disposing linac or replacing components, is difficult, as the standards for the radioactive material management are not clear in Korea. We surveyed the management status of radioactive components occurred from medical linacs in Korea. And we also measured the activation of each part of the discarded Elekta linac using a survey meter and portable High Purity Germanium (HPGe) detector. We found that most medical institutions did not perform radiation measurements when disposing of radioactive components. The radioactive material was either stored within the institution or collected by the manufacturer. The surface dose rate measurements showed that the parts with high surface dose rates were target, primary collimator, and multileaf collimator (MLC). 60Co nuclide was detected in most parts, whereas for the target, 60Co and 184Re nuclides were detected. Results suggest that most institutions in Korea did not have the regulations for disposing radioactive waste from linac or the management procedures and standards were unclear. Further studies are underway to evaluate short-lived radionuclides and to lay the foundation for radioactive waste management from medical linacs.
의료용 선형가속기의 헤드 구성요소인 표적물질과 일차 콜리메이터는 선속특징을 결정짓는데 가장 큰 영향을 미치며 이로 인해 발생하는 후방산란은 구조물 차폐와 장비 관리 관점에서 고려하여야 할 요소이다. 이에 본 연구에서는 몬테카를로 시뮬레이션 중 하나인 Geant4를 통해 선형가속기를 모델링하고 헤드 구성요소의 변화에 따른 후방산란 양상을 살펴보았다. 산란되어 발생한 전자의 경우, 표적물질이 위치한 일차 콜리메이터의 내부 반경에 대부분의 분포를 보였으며 이와 반대로 산란된 광자의 경우, 바깥쪽 영역에서 상대적으로 높은 에너지의 산란이 많음을 알 수 있었다. 산란된 양전자는 약 0.03%로 미미한 발생을 보였다. 일차 콜리메이터의 내부 반경이 달라짐에 따라 세 산란입자(전자, 광자, 양전자) 모두 반경 내부 쪽에서의 변화가 컸으며, 전체 반경의 변화에 따른 후방산란은 60 mm 이상에서부터 어느 정도의 영향을 보인다는 것을 알 수 있었다. 표적물질 두께의 변화에는 큰 영향을 받지 않는 것으로 나타났다. 이를 통하여 가속시킨 초기 전자에 대한 후방 쪽으로의 산란도 무시할 수 없음을 알 수 있었으며 주변 구성요소의 기하학적인 형태나 크기에 의해서도 후방산란의 양상이 달라질 수 있음을 알 수 있었다. 따라서 산란된 입자들의 에너지 분포를 통해 장비 관리의 관점에서도 고려하여야 할 결과라고 사료된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.