• 펄프종이기술
• /
• 제46권6호
• /
• pp.50-55
• /
• 2014

An oxidized starch was modified for surface sizing via etherification and esterification. Propylene oxide (PO), sodium monochloroacetate (SMCA), and acrylonitrile (AN) were used as etherification, and vinyl acetate monomer (VAM), maleic anhydride (MA), fumaric acid (FA), and itaconic acid (ITA) were used for esterification. Esterification and etherification of starch decreased both Brookfield viscosity and Brabender viscosity substantially even though the solids level was increased by 2% from 14 to 16%. Surface sizing performance of starches in tensile strength, stiffness and compressive strength was improved by esterification and etherification of the oxidized starch. Especially, SMCA etherification was found to be the most effective modification method.

• 대한화학회지
• /
• 제47권6호
• /
• pp.591-596
• /
• 2003

아미노싸이에노피리다진(1a, b)과 아미노싸이에노쿠마린(2)은 DMFDMA와 축합반응을 하여 아미딘(3a, b)을 형성한다. 이 화합물들을 N-페닐말레이마이드와 반응시키면 화합물 9와 10이 얻어진다. 반면에 3a, b, 4, 18, 19, 20을 말레산 무수물과 반응시키면 포밀 유도체인 5a, b, 6, 21, 22, 23 들이 얻어진다. 아미딘 화합물 3a, b 를 다이에틸 퓨마레이트와 반응시키면 가수분해산물인 아미딘 14를 거쳐 11이 얻어진다. N-페닐말레이마이드를 마이크로웨이브 오븐에서 반응시키면 [2+2]와 [2+2+2] 고리첨가반응 산물이 얻어진다.

• Macromolecular Research
• /
• 제17권6호
• /
• pp.417-423
• /
• 2009

The effects of maleic anhydride-grafted polypropylene (PP-g-MAH) addition on polypropylene (PP) and poly(acrylonitrile-butadiene-styrene) (ABS) blends were studied. Blends of PP/ABS (70/30, wt%) with PP-g-MAH were prepared by a twin-screw extruder. From the results of mechanical testing, the impact, tensile and flexural strengths of the blends were maximized at a PP-g-MAH content 3 phr. The increased mechanical strength of the blends with the PP-g-MAH addition was attributed to the compatibilizing effect of the PP and ABS blends. In the morphological studies, the droplet size of ABS was minimized (6.6 ${\mu}m$) at a PP-g-MAH content of 3 phr. From the rheological examination, the complex viscosity was maximized at a PP-g-MAH content of 3 phr. These mechanical, morphological and rheological results indicated that the compatibility of the PP/ABS (70/30) blends is increased with PP-g-MAH addition to an optimum blend at a PP-g-MAH content of 3 phr.

• 폴리머
• /
• 제38권5호
• /
• pp.613-619
• /
• 2014

The polypropylene/polyamide elastomer (PP/PAE) blends were prepared by melt mixing. PP and PAE in PP/ PAE were immiscible completely. The size of PAE domains was large and the clear gap in the interface between PP and PAE existed, which did not meet the conditions enhancing toughness of polymers by elastomer. Therefore, maleic anhydride grafted polypropylene (MP) was used to improve the miscibility between PP and PAE. The miscibility between PP and PAE was improved and the size of dispersed phase PAE decreased by introducing MP. The crystallization of PP became easier by introducing PAE as a nucleating agent. With the increase of PAE content, the melt-crystallization temperatures of PP components in PP/PAE/MP blends increased gradually. The melt-crystallization of the polytetramethylene oxide segment of PAE component in PP/PAE blends were hampered by PP component. In addition, PAE can enhance significantly the toughness of PP, and the tensile strength and modulus did not decrease.

• Macromolecular Research
• /
• 제16권5호
• /
• pp.404-410
• /
• 2008

In order to obtain 'value added products' from polypropylene (PP)/waste ground rubber tire powder (WGRT) composites, PP/WGRT microcellular foams were prepared via supercritical carbon dioxide. The effects of blend composition and processing condition on the cell size, cell density and relative density of PP/WGRT micro-cellular composites were studied. The results indicated that the microcellular structure was dependent on blend composition and processing condition. An increased content of waste ground rubber tire powder (WGRT) and maleic anhydride-grafted styrene-ethylene-butylene-styrene (SEBS-g-MA) reduced the cell size, and raised the cell density and relative density, whereas a higher saturation pressure increased the cell size, and reduced the cell density and relative density. With increasing saturation temperature, the cell size increased and the relative density decreased, whereas the cell density initially increased and then decreased.

• Advanced Composite Materials
• /
• 제17권3호
• /
• pp.191-214
• /
• 2008

Polypropylene/layered silicate nanocomposites containing maleic anhydride grafted polypropylene were prepared by melt compounding and their rheological behavior was investigated in shear flow. Transient and steady shear flows were simulated numerically by using the K-BKZ integral constitutive equation along with experimentally determined damping functions under dynamic oscillatory and step strain shear flows. Nonlinear shear responses were predicted with the K-BKZ constitutive equation using two different damping functions such as the Wagner and PSM models. It was observed that PP-g-MAH compatibilized PP/layered silicate nanocomposites have stronger and earlier shear thinning and higher steady shear viscosity than pure PP resin or uncompatibilized nanocomposites at low shear rate regions. Strong damping behavior of the PP/layered silicate nanocomposite was predicted under large step shear strain and considered as a result of the strain-induced orientation of the organoclay in the shear flow. Steady shear viscosity of the pure PP and uncompatibilized nanocomposite predicted by the K-BKZ model was in good agreement with the experimental results at all shear rate regions. However, the model was inadequate to predict the steady shear viscosity of PP-g-MAH compatibilized nanocomposites quantitatively because the K-BKZ model overestimates strain-softening damping behavior for PP/layered silicate nanocomposites.

• 한국재료학회지
• /
• 제12권1호
• /
• pp.10-15
• /
• 2002

Melt blends of maleic anhydride grafted polypropylerle(PP-g-MA) and Nylon 6 were prepared to study the influence of chemical reaction between the two polymer components. By adding the MA grafted polystyrene pold (ethylene/butadiene) and polystyrene[SEBS-g-MA] as the compatible modifiers to reinforce the impact resistance, the Izod impact strength, high rate impact strength and morphology were studied. The notched Izod impact strength increased with the content of PP-g-MA and SEBS- g-MA. The energy of high rate impact strength increased as the thickness of specimen increased, while, it increased as the specimen displacement decreased. In the morphology observed by SEM, finally, we confirmed the improvement of the compatibilization and interfacial adhesion with the content of SEBS-g-MA. The continuous phase of PP-g-MA was the main cause of the modified properties.

• 한국식품영양과학회지
• /
• 제24권4호
• /
• pp.570-577
• /
• 1995

Aspergillus sp. SB-2704 was selected for its strong polygalacturonase activity among various strain of mold found in soil. It was found that production of polygalacturonase reached to maximum when the wheat bran medium containing 1% polypepton, 1% glucose, and 0.2% FeSO4 were cultured for 3 days at 35$^{\circ}C$. Polygalacturonase was purified 20.90 fold from Aspergillus SB-2704. The purification procedures include ammonium sulfate treatment, gel filtration on Sephdex G-150 and DEAE-cellulose ion exchange chromatography. Yield of the enzyme purification was 4.34%. Purified enzyme was confirmed as a single band by the polyacrylamide gel electrophoresis. When the purified enzyme was applied to SDS-polyacrylamide gel electrophoresis, the molecular weight was estimated to be 36,000. The optimum pH for the enzyme activity was 5.5 and optimum temperature was 5$0^{\circ}C$. The enzyme is stable in acidic condition. The activity of purified enzyme was inhibited by Pb2+, Hg2+ and Ba2+, whereas activated by Cu2+, Mn2+, Mg2+ and Fe2+. The activity of polygalacturonase was inhibited by the treament wit maleic anhydride, iodine, and EDTA. The result indicate the possible involvement of histidine and metal ion at active site.

• 폴리머
• /
• 제24권3호
• /
• pp.366-373
• /
• 2000

본 연구에서는 poly(phenylene sulfide)(PPS)와 ABS의 물성을 상호보완하기 위하여 블렌드를 제조하였다. 각 성분간의 상용성을 증진시키기 위하여 소량의 무수말레인산을 ABS에 반응시켜 MABS (ABS-g-MAH)를 제조하였으며, PPS/ABS 및 PPS/MABS 블렌드는 이축 혼련 압출기를 이용하여 용융 흔합하였다. 블렌드에서 ABS의 화학적 개질이 블렌드의 모폴로지와 열적 성질에 미치는 영향을 관찰하였다. PPS/MABS 블렌드의 경우, 각 성분간에 강한 인력이 형성되는 것을 광학현미경과 SEM을 이용하여 확인하였으며, DMA 분석에서는 단일 유리전이 온도를 확인하였다. 또한 화학적으로 개질된 MABS를 사용한 PPS/MABS의 블렌드는 PPS/ABS보다 향상된 열적 성질을 나타내었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.231-236
• /
• 2008

양이온 개환중합법을 이용하여 Epichlorohydrin(ECH)과 Tetrahydrofuran(THF)을 공중합 하였다. 중합은 1,4-Butandiol 존재 하에 $BF_3THF$를 촉매로 사용하여 잘 제어된 Copolyetherdiol을 합성하였다. 분자량은 [monomer]/[diol]비를 조절하였고, 공중합체 조성은 ECH와 THF의 투입몰비를 변화하여 조절하였다. 합성된 Copolyetherdiol의 Chlorine기는$S_N2$반응을 이용하여 Azide기로 치환하였다. 합성된 고분자를 프리폴리머로 사용하여 경화제인 N-100/IPDI와 경화촉매인 TPB/MA 혼합촉매를 이용하여 Polyurethane을 합성하여 경화거동과 기계적 특성은 비교 분석하였다.