• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.1-2
• /
• 2011

Hybrid rockets have lately attracted attention as a strong candidate of small, low cost, safe and reliable launch vehicles. A significant topic is that the first commercially sponsored space ship, SpaceShipOne vehicle chose a hybrid rocket. The main factors for the choice were safety of operation, system cost, quick turnaround, and thrust termination. In Japan, five universities including Hokkaido University and three private companies organized "Hybrid Rocket Research Group" from 1998 to 2002. Their main purpose was to downsize the cost and scale of rocket experiments. In 2002, UNISEC (University Space Engineering Consortium) and HASTIC (Hokkaido Aerospace Science and Technology Incubation Center) took over the educational and R&D rocket activities respectively and the research group dissolved. In 2008, JAXA/ISAS and eleven universities formed "Hybrid Rocket Research Working Group" as a subcommittee of the Steering Committee for Space Engineering in ISAS. Their goal is to demonstrate technical feasibility of lowcost and high frequency launches of nano/micro satellites into sun-synchronous orbits. Hybrid rockets use a combination of solid and liquid propellants. Usually the fuel is in a solid phase. A serious problem of hybrid rockets is the low regression rate of the solid fuel. In single port hybrids the low regression rate below 1 mm/s causes large L/D exceeding a hundred and small fuel loading ratio falling below 0.3. Multi-port hybrids are a typical solution to solve this problem. However, this solution is not the mainstream in Japan. Another approach is to use high regression rate fuels. For example, a fuel regression rate of 4 mm/s decreases L/D to around 10 and increases the loading ratio to around 0.75. Liquefying fuels such as paraffins are strong candidates for high regression fuels and subject of active research in Japan too. Nakagawa et al. in Tokai University employed EVA (Ethylene Vinyl Acetate) to modify viscosity of paraffin based fuels and investigated the effect of viscosity on regression rates. Wada et al. in Akita University employed LTP (Low melting ThermoPlastic) as another candidate of liquefying fuels and demonstrated high regression rates comparable to paraffin fuels. Hori et al. in JAXA/ISAS employed glycidylazide-poly(ethylene glycol) (GAP-PEG) copolymers as high regression rate fuels and modified the combustion characteristics by changing the PEG mixing ratio. Regression rate improvement by changing internal ballistics is another stream of research. The author proposed a new fuel configuration named "CAMUI" in 1998. CAMUI comes from an abbreviation of "cascaded multistage impinging-jet" meaning the distinctive flow field. A CAMUI type fuel grain consists of several cylindrical fuel blocks with two ports in axial direction. The port alignment shifts 90 degrees with each other to make jets out of ports impinge on the upstream end face of the downstream fuel block, resulting in intense heat transfer to the fuel. Yuasa et al. in Tokyo Metropolitan University employed swirling injection method and improved regression rates more than three times higher. However, regression rate distribution along the axis is not uniform due to the decay of the swirl strength. Aso et al. in Kyushu University employed multi-swirl injection to solve this problem. Combinations of swirling injection and paraffin based fuel have been tried and some results show very high regression rates exceeding ten times of conventional one. High fuel regression rates by new fuel, new internal ballistics, or combination of them require faster fuel-oxidizer mixing to maintain combustion efficiency. Nakagawa et al. succeeded to improve combustion efficiency of a paraffin-based fuel from 77% to 96% by a baffle plate. Another effective approach some researchers are trying is to use an aft-chamber to increase residence time. Better understanding of the new flow fields is necessary to reveal basic mechanisms of regression enhancement. Yuasa et al. visualized the combustion field in a swirling injection type motor. Nakagawa et al. observed boundary layer combustion of wax-based fuels. To understand detailed flow structures in swirling flow type hybrids, Sawada et al. (Tohoku Univ.), Teramoto et al. (Univ. of Tokyo), Shimada et al. (ISAS), and Tsuboi et al. (Kyushu Inst. Tech.) are trying to simulate the flow field numerically. Main challenges are turbulent reaction, stiffness due to low Mach number flow, fuel regression model, and other non-steady phenomena. Oshima et al. in Hokkaido University simulated CAMUI type flow fields and discussed correspondence relation between regression distribution of a burning surface and the vortex structure over the surface.

• 설비공학논문집
• /
• 제27권7호
• /
• pp.380-394
• /
• 2015

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2014. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of heat and mass transfer, cooling and heating, and air-conditioning, the flow inside building rooms, and smoke control on fire. Research issues dealing with duct and pipe were reduced, but flows inside building rooms, and smoke controls were newly added in thermal and fluid engineering research area. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results for thermal contact resistance measurement of metal interface, a fan coil with an oval-type heat exchanger, fouling characteristics of plate heat exchangers, effect of rib pitch in a two wall divergent channel, semi-empirical analysis in vertical mesoscale tubes, an integrated drying machine, microscale surface wrinkles, brazed plate heat exchangers, numerical analysis in printed circuit heat exchanger. In the area of pool boiling and condensing, non-uniform air flow, PCM applied thermal storage wall system, a new wavy cylindrical shape capsule, and HFC32/HFC152a mixtures on enhanced tubes, were actively studied. In the area of industrial heat exchangers, researches on solar water storage tank, effective design on the inserting part of refrigerator door gasket, impact of different boundary conditions in generating g-function, various construction of SCW type ground heat exchanger and a heat pump for closed cooling water heat recovery were performed. (3) In the field of refrigeration, various studies were carried out in the categories of refrigeration cycle, alternative refrigeration and modelling and controls including energy recoveries from industrial boilers and vehicles, improvement of dehumidification systems, novel defrost systems, fault diagnosis and optimum controls for heat pump systems. It is particularly notable that a substantial number of studies were dedicated for the development of air-conditioning and power recovery systems for electric vehicles in this year. (4) In building mechanical system research fields, seventeen studies were reported for achieving effective design of the mechanical systems, and also for maximizing the energy efficiency of buildings. The topics of the studies included energy performance, HVAC system, ventilation, and renewable energies, piping in the buildings. Proposed designs, performance performance tests using numerical methods and experiments provide useful information and key data which can improve the energy efficiency of the buildings. (5) The field of architectural environment was mostly focused on indoor environment and building energy. The main researches of indoor environment were related to the evaluation of work noise in tunnel construction and the simulation and development of a light-shelf system. The subjects of building energy were worked on the energy saving of office building applied with window blind and phase change material(PCM), a method of existing building energy simulation using energy audit data, the estimation of thermal consumption unit of apartment building and its case studies, dynamic window performance, a writing method of energy consumption report and energy estimation of apartment building using district heating system. The remained studies were related to the improvement of architectural engineering education system for plant engineering industry, estimating cooling and heating degree days for variable base temperature, a prediction method of underground temperature, the comfort control algorithm of car air conditioner, the smoke control performance evaluation of high-rise building, evaluation of thermal energy systems of bio safety laboratory and a development of measuring device of solar heat gain coefficient of fenestration system.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권1호
• /
• pp.73-80
• /
• 2022

본 연구에서는 공장에서 L형강을 이용하여 선조립한 NRC 보와 NRC 기둥을 현장에서 볼트 조립하는 NRC 보-기둥접합부 상세를 개발하였다. 개발된 접합부 상세는 NRC-J형과 NRC-JD형이다. NRC-J형은 NRC 기둥 측면의 강재 플레이트와 NRC 보의 엔드플레이트의 측면과 하부면에 TS볼트로 인장접합하는 방식이다. NRC-JD형은 전단에 대해서 NRC 보와 NRC 기둥의 측면을 고력볼트접합하고, 휨에 대해서 접합부를 관통하는 철근연결재와 보의 보강재를 겹침이음하도록하는 강접합 방식이다. 접합부 내진성능평가를 위하여, 두 가지 NRC 보-기둥 접합부 상세를 가지는 NRC-J 실험체, NRC-JD 실험체와 RC 보-기둥 접합부 상세를 가지는 RC-J 실험체 등 3개의 실험체를 제작하였다. 반복횡하중가력 실험결과, 모든 실험체의 최종 파괴형상은 보-기둥 접합면에서 보의 휨파괴로 나타났다. 정가력에 의한 실험체 최대내력은 RC-J 실험체에 비하여 NRC-J 실험체와 NRC-JD 실험체가 각각 10.1%, 29.6% 크게 나타났다. 두가지 NRC 접합부 상세 모두 KDS 기준(KDS 41 3100)의 합성중간모멘트골조 모멘트접합부에서 요구되는 최소 총층간변위각 0.03 rad 이상의 연성능력을 확보는 것으로 평가되었다. 부재각 5.7%에서 NRC-J실험체, NRC-JD 실험체가 RC실험체에 비해 약 34.8%, 61.1% 큰 누적 에너지 소산능력을 보유하고 있었다. NRC 보-기둥 접합부의 실험내력이 KDS 기준식에 의한 이론내력에 비하여 30%~53% 큰 것으로 평가되어, 기준식이 보유성능을 안전측으로 평가하였다.

• 한국강구조학회 논문집
• /
• 제16권6호통권73호
• /
• pp.725-736
• /
• 2004

최근 국내에서 I형 거더의 외부가 강재로 이루어지고 내부에 무근콘크리트가 채워져 합성된 거더에 프리스트레스를 도입하여 경간을 장대화할 수 있는 새로운 개념의 합성거더인 '강재로 구속된 프리스트레스트 콘크리트 합성거더(Steel-Confined Prestressed Concrete Girder; SCP Girder)'가 개발되었다. 또한 개발된 거더를 실물크기로 제작하여 시공성을 확인하고 정적하중 재하에 의한 파괴실험을 통해 공용 중 안전성에 대한 실험적 검증이 수행되었다(김정호 등, 2002). 그러나 SCP 합성거더의 실용화를 위해서는 교량 파손의 주원인이 주행하중의 영향에 의한 피로파손인 점을 고려하여 반복하중에 대한 피로거동의 연구 및 피로 안전성 확보가 요구된다. 따라서 본 연구에서는 SCP 합성거더에 대한 피로거동 특성을 파악하고 피로설계를 위한 기초적인 자료를 제시하기 위해 피로실험을 실시하였다. 피로실험을 위한 시험체의 제작은 1등교에 해당하는 설계활하중(DB-24)에 대하여 10m 지간으로 설계 제작하였으며, 실험결과 도로교설계기준(한국도로교통협회, 2000)의 상세피로범주에 따른 허용피로응력범위를 초과하지 않는 것으로 나타났다. 또한 초기정적재하를 통해 설계의 타당성과 구조적 거동을 분석하였으며, 피로실험 종료 후 거더 외부를 이루고 있는 강재를 제거하여 내부콘크리트의 상태를 관찰하였다.

• 한국전자파학회논문지
• /
• 제20권4호
• /
• pp.344-350
• /
• 2009

본 논문에서는 새로운 빔 조향 방식을 갖는 하이브리드 안테나를 제안하였다. 본 안테나는 카세그레인 안테나 구조로서, 파라볼라 구조의 고이득 특성을 구현하기 위하여 설계된 주반사판과 평판형 구조로서 모든 방향에서 ${\pm}3^{\circ}$ 회전할 수 있도록 설계된 부반사판의 경사각을 이용하여 안테나 빔 조향(beam pointing)을 제어할 수 있도록 하였다. 또한, 20개의 소자 안테나로 구성되는 능동 배열을 급전부에 적용함으로써, 일차적으로 급전 배열에 의한 전자식 빔 조향 제어와 함께, 부 반사판의 경사각을 이용한 이차적인 빔 조향 제어가 가능하도록 하였다. 본 안테나는 이동체 내에서 위성을 통한 멀티미디어 서비스를 제공할 수 있도록 설계되었으며, 무궁화위성의 사양에 맞춰 송신은 Ka-대역(30.085$\sim$30.885 GHz)에서, 수신은 K-대역(20.355$\sim$21.155 GHz)에서 동작하도록 설계되었다. 또한, 제작된 시제품 안테나의 특성 시험을 통하여, 송신 및 수신 대역에서 최소 47 dBi와 44.4 dBi의 안테나 이득을 가지며, 급전 배열 및 부 반사판을 통하여 안테나의 빔이 ${\pm}2^{\circ}$ 범위까지 가변할 수 있음을 확인하였다.

• 한국환경보건학회지
• /
• 제25권3호
• /
• pp.36-43
• /
• 1999

The present study was performed to investigate biodegradation rate of dichlorvos and methidathion. In the biodegradation test of two pesticides by the modified river die-away method from June 17 to August 22, 1998, the biodegradation rate constants and half-life were determined in Nakdong(A) and Kumho River(B). Biodegradation rate of dichlorvos was 4.51% in A sampling point, 6.88% in B sampling point after 7 days. Biodegradation rate constants and half-life of dichlorvos were 0.0066 and 105 days in A sampling point, 0.0102 and 67.9 days in B sampling point, respectively. Biodegradation rate of methidathion was 23% in A sampling point, 36% in B sampling point after 7 days. Biodegradation rate constants and half-life of methidathion were 0.0377 and 18.4 days in A sampling point, 0.0641 and 10.8 days in B sampling point, respectively. Biodegradation rate of methidathion was faster than that of dichlorvos. This suggested that the difference in biodegradation of pesticides was due to difference in the water quality and standard plate counts in the Nackdong and Kumho Rivers. The result of correlation analysis between biodegradation rate constants of the pesticides and water quality(DO, BOD, SS, ABS, NH$_3$-N, and NO$_3$-N) showed significant correlation with BOD, SS and NH$_3$-N at the 5% significant level. A significant linear equation was obtained from regression analysis at the 5% significant level, whereas, dependent variables were BOD, SS and NH$_3$-N, and the biodegradation rate constant was independent variable. It is suggested that dichlorvos will be mainly degraded by hydrolysis, and for methidathion was both hydrolysis and biodegradation. A significant QSAR equation was obtained from regression analysis at the 10% significant level, whereas, dependent variable is biodegradation rate constants of BPMC, chlorothalonil, dichlorvos and methidathion, vapor pressures, partition coefficients and water solubilities of the pesticides are independent variables. Also, a significant linear equation was obtained from regression analysis at the 1% significant level, whereas, dependent variable is biodegradation rate constants of BPMC, chlorothalonil, dichlorvos and methidathion, hydrolysis rate constants of the pesticides are independent variables. It is suggested that the pesticides will be degraded by main degradation factor when the pesticides was affected both hydrolysis and biodegradation.

• 한국전산구조공학회논문집
• /
• 제25권6호
• /
• pp.505-512
• /
• 2012

본 논문에서는 일차전단변형 평판 이론(FSDT)의 개선을 통한 복합재료 적층평판의 효율적 열응력 해석 기법을 제안한다. 횡방향 응력 성분에 대해서만 변분을 취하는 혼합변분이론(Mixed variational theorem)을 이용하여 횡방향 변형에너지를 개선하였다. 가정된 횡방향 전단응력 성분들은 효율적 고차이론으로부터 구하였으며, 면내 변위 성분들은 일차적층평판 이론의 변위장을 사용하였다. 또한, 열응력 해석에 있어서 횡방향 수직 변형을 효과적으로 고려하기 위해서 횡방향 수직 변위를 두께방향에 대하여 포물선으로 가정하였다. 이 과정을 통하여 얻어진 전단변형 에너지를 본 논문에서는 횡방향 수직 변형이 고려된 개선된 일차전단변형이론(EFSDTM_TN)이라고 명명하였다. 제안된 EFSDTM_TN은 복합재료 적층평판의 열탄성 거동을 해석함에 있어서 횡방향 수직 변형이 고려된 일차전단변형 평판 이론(FSDT_TN)과 비슷한 수준의 계산만을 필요로 하며, 동시에 후처리 과정을 통하여 열변형 및 열응력의 두께방향 분포를 정확하게 예측할 수 있도록 개선하였다. 계산된 결과는 FSDT_TN, 3차원 탄성해 등의 결과와 비교하여 검증하였다.

• 암석학회지
• /
• 제24권4호
• /
• pp.323-335
• /
• 2015

달전현무암은 포항분지의 발달사 해석에 중요한 의미를 가지나 야외 산상, 층서적 위치, 동위원소 연대 등에서 연구자들 간에 많은 논란이 있다. 본 연구는 이러한 논란을 해결하기 위해 상세한 야외조사를 통해 이 암석의 분포와 연일층군과의 접촉관계를 밝히고 지화학 자료를 분석하였으며, $^{40}Ar/^{39}Ar$ 동위연소 연대를 측정하였다. 달전저수지 주변에는 연일층군과 관입접촉 관계를 가지는 3매의 현무암체와 10여 개의 소규모 암맥과 암상이 분포하고 있음이 밝혀졌다. 경하관찰에서 이들은 감람석과 휘석을 반정으로 하는 반상조직을 보이며 기질은 사장석, 감람석, 휘석 등으로 구성된 알칼리 현무암의 특징을 보인다. 기존 지화학 분석결과를 재구성한 결과, 3 매의 암체와 소규모 관입암들은 TAS 도표, 미량원소와 희토류원소 패턴, Zr-Ti 도표상에서 모두 동일한 지화학적 특성을 보이고 있다. 이들은 모두 알칼리 계열로 도시되며, 부화된 해양성 현무암 또는 지판 내의 알칼리 현무암과 유사한 원소별 패턴을 보인다. 또한 $^{40}Ar/^{39}Ar$ 동위연소 연대측정 결과, 13.82 Ma의 등시선 연대가 도출되었다. 이러한 결과들은 종합하면, 달전현무암은 알칼리 현무암으로써 층서적으로 연일층군을 관입한 포항분지 충전물에 속하는 것으로 결론지어진다.

• 수산해양기술연구
• /
• 제25권2호
• /
• pp.87-104
• /
• 1989

Recently, with the tendency of more lightening, high-strength and high-speed in the marine industries such as marine structures, ships and chemical plants, the use of the aluminium Alloy is rapidly enlarge and there occurs much interest in the study of corrosion fatigue crack characteristics. In this paper, the initiation of surface crack and the propagation characteristics on the base metal and weld zone of 5086-H116 Aluminium Alloy Plate which is one of the Al-Mg serious alloy(A5000serious) used most when building the special vessels, were investigated by the plane bending corrosion fatigue under the environments of marine, air and applying cathodic protection. The effects of various specific resistances on the initiation, propagation behavior of corrosion fatigue crack and corrosion fatigue life in the base metal and heat affected zone were examined and its corrosion sensitivity was quantitatively obtained. The effects of corrosion on the crack depth in relation to the uniform surface crack length were also investigated. Also, the structural, mechanical and electro-chemical characteristics of the metal at the weld zone were inspected to verify the reasons of crack propagation behavior in the corrosion fatigue fracture. In addition, the effect of cathodic protection in the fracture surface of weld zone was examined fractographically by Scanning Electron Microscope(S.E.M.). The main results obtained are as follows; (1) The initial corrosion fatigue crack sensitibity under specific resistance of 25Ω.cm% show 2.22 in the base metal and 19.6 in the HEZ, and the sensitivity decreases as specific resistance increases (2) By removing reinforcement of weldment, the initiation and propagation of corrosion crack in the HAZ are delayed, and corrosion fatigue life increases. (3) As specific resistance decreases, the sensitivity difference of corrosion fatigue life in the base metal and HAZ is more susceptible than that of intial corrosion fatigue crack. (4) Experimental constant, m(Paris' rule) in the marine environment is in the range of about 3.69 to 4.26, and as specific resistance increases, thje magnitude of experimental constant, also increases and the effect by corrosion decreases. (5) Comparing surface crack length with crack depth, the crack depth toward the thickness of specimen in air is more deeply propagated than that in corrosion environment. (6) The propagation particulars of corrosion fatigue crack for HAZ under initial stress intensity factor range of $\Delta$k sub(li) =27.2kgf.mm super(-3/2) and stress ratio of R=0 shows the retardative phenomenon of crack propagation by the plastic deformation at crack tip. (7) Number of stress cycles to corrosion fatigue crack initiation of the base metal and the welding heat affected zone are delayed by the cathodic protection under the natural sea water. The cathodic protection effect for corrosion fatigue crack initiation is eminent when the protection potential is -1100 mV(SCE). (8) When the protection potential E=-1100 mV(SCE), the corrosion fatigue crack propagation of welding heat affected zone is more rapid than that of the case without protection, because of the microfissure caused by welding heat cycle.

• 암석학회지
• /
• 제11권3_4호
• /
• pp.182-199
• /
• 2002

한반도 남동부에서 관찰된 총 287개 암맥들의 암석기재와 지화학적 자료들로부터 그 특성과 기원 마그마의 진화 경로를 밝히고자 하였다. 암맥들은 야외에서 염기성, 중성, 산성 암맥군으로 분류되며. 다시 염기성 암맥은 3개 그룹, 중성 암맥은 2개 그룹, 산성 암맥은 2개 그룹으로 각각 재분류된다. 이 중 염기성 암맥의 그룹(I)에 해당하는 암맥들이 연구지역에 가장 우세하게 산출되는데, 이들은 연일구조선을 경계로 하여 양쪽에 모두 분포하며 동일한 암석기재학 그리고 지화학적 특징을 보여주었다. 이는 선행 연구에서 밝혀진 바와 같이 연일구조선 양편의 암맥들이 모두 동시기에 만들어졌음을 의미하며 연일구조선이 마이오세 지각변형기 동안 지괴의 시계방향 수평 회전운동을 규제한 주요 구조선이었음을 강력히 지지한다. 암맥들의 지화학적 특징들은 암석기재적으로 분류한 7개 그룹에 따라 서로 잘 구분되었다 염기성, 중성, 산성 암맥들은 각각 현무암과 현무암질 안산암, 안산암과 데사이트 그리고 유문암에 해당되며, 마그마 계열은 대부분 칼크-알칼리계열에 해당된다. 지화학 자료는 염기성 암맥들에서 감람석, 단사휘석, 사장석의 분별정출 작용이 있었음을 지시하며, 특정 원소들의 함량과 조구조 판별도에서는 연구지역 암맥들이 지판의 침강 섭입과 관련된 마그마로부터 유래되었고 그 조구조 환경이 조산대 화산호와 관련이 있음을 보여주었다.