• Journal of the Korean Magnetics Society
• /
• v.2 no.1
• /
• pp.22-28
• /
• 1992

Barium ferrite thin films were reactively deposited with Fe and BaO composite targets by a facing tergects sputtering unit. When thermally oxidized silicon wafers were used as substrates, minimum substrate heating of $750^{\circ}C$ was necessary for the perfect c-axis alignment in barium ferrite films. To lower the critical substrate temperature for the good c-axis alignment, such seed layers as ZnO, ${\alpha}-Fe_{2}O_{3}$ and ${\gamma}-Fe_{2}O_{3}$ were tested. The excellent c-axis algnment of BaM was obtained at a substrate temperature of $600^{\circ}C$ on ZnO seed layer whose (002) plane was parallel to the substrate surface. The magnetic properties of the BaM film showed saturation magnetization of 295 emu/cc, perpendicular coercivity of 1.7 kOe and squareness of 0.75. Optimum deposition rate of $230\;{\AA}/min$ was obtained with the composite target and this was 5 to 20 times higher than those of other investigators with oxide targets.

• Journal of Biomedical Engineering Research
• /
• v.36 no.6
• /
• pp.241-250
• /
• 2015

Noninvasive temperature monitoring is feasible with Magnetic Resonance Imaging (MRI) based on temperature sensitive MR parameters such as $T_1$ and $T_2$ relaxation times, Proton Resonance Frequency shift (PRFs), diffusion, exchange process, magnetization transfer contrast, chemical exchange saturation transfer, etc. While the temperature monitoring is very useful to guide the thermal treatment such as RF hyperthermia or thermal ablation, the optimization of the MR thermometry method is essential because the range of temperature measurement depends on the choice of the measurement methods. Useful temperature range depends on the purpose of treatment methods, for example, $42^{\circ}C$ to $45^{\circ}C$ for RF hyperthermia and over $50^{\circ}C$ for thermal ablation. In this paper, MR thermometry methods using $T_1$ and $T_2$ relaxation times and PRFs-based MR thermometry are tried on a 3.0 T MRI system and their results are reported and compared. In addition, the scanning protocol and temperature calculation algorithms from $T_1$ and $T_2$ relaxation times and PRFs are optimized for the different temperature ranges for the purpose of RF hyperthermia and/or thermal ablation.

• Journal of the Korean Society for Railway
• /
• v.15 no.2
• /
• pp.135-140
• /
• 2012

Interior Permanent Magnet Synchronous motors (IPMSM) with concentrated winding are superior to distributed winding in the power density point of view. But it causes huge amount of eddy current losses on the permanent magnet. This paper presents the optimal permanent magnet V-shape on the rotor of an interior permanent magnet synchronous motor to reduce the core losses and improve the performance. Each eddy current loss on permanent magnet has been investigated in detail by using FEM (Finite Element Method) instead of equivalent magnetic circuit network method in order to consider saturation and non-linear magnetic property. Simulation-based design of experiment is also applied to avoid large number of analyses according to each design parameter and consider expected interactions among parameters. Consequently, the optimal design to reduce the core loss on the permanent magnet while maintaining or improving motor performance is proposed by an optimization algorithm using regression equation derived and lastly, it is verified by FEM.

• Journal of the Korean Magnetics Society
• /
• v.18 no.1
• /
• pp.14-18
• /
• 2008

Bismuth-substituted yttrium iron garnet(Bi:YIG) films, which show excellent magnetic and magneto-optical properties as well as low optical losses by optimizing their deposition and post-annealing condition, have been attracting great attention in optical device research area. In this study, the Bi:YIG thick films were deposited with the aerosol deposition method for the final purpose of applying them to optical isolators. Since the aerosol deposition is based on the impact adhesion of sub-micrometer particles accelerated by a carrier gas to a substrate, the flow rate of carrier gas, which is in proportion to mechanically collision energy, should be treated as an important parameter. The Bi:YIG($Bi_{0.5}Y_{2.5}Fe_5O_{12}$) particles with $100{\sim}500$ nm in average diameter were carried and accelerated by nitrogen gas with the flow rate of 0.5 l/min${\sim}$10 l/min. The coercive force decreased from 51 Oe to 37 Oe exponentially with increasing gas flow rate. This is presumably due to the fact that the optimal collision energy results in reduction of impurity and pore, which makes the film to be soft magnetically. The saturation magnetization decreased due to crystallographical distortion of the film with increasing gas flow rate.

• Journal of Magnetics
• /
• v.10 no.1
• /
• pp.5-9
• /
• 2005

Nanoparticles $Ni_{0.9}Zn_{0.1}Fe_2O_4$ is fabricated by a sol-gel method. The magnetic and structural properties of powders were investigated with XRD, SEM, Mossbauer spectroscopy, and VSM. $Ni_{0.9}Zn_{0.1}Fe_2O_4$ powders annealed at $300{^{\circ}C}$ have a spinel structure and behaved superparamagnetically. The estimated size of $Ni_{0.9}Zn_{0.1}Fe_2O_4$ nanoparticle is about 10 nm. The hyperfine fields at 13 K for the A and B patterns are found to be 533 and 507 kOe, respectively. The ZFC curves are rounded at the blocking temperature ($T_B$)and show a paramagnetic-like behavior above $T_B$. $T_B$ of $Ni_{0.9}Zn_{0.1}Fe_2O_4$ nanoparticle is about 250 K. Nanoparticles $Ni_{0.9}Zn_{0.1}Fe_2O_4$ annealed at 400 and $500{^{\circ}C}$ have a typical spinel structure and is ferrimagnetic in nature. The isomer shifts indicate that the iron ions were ferric at the tetrahedral (A) and the octahedral (B). The saturation magnetization of nanoparticles $Ni_{0.9}Zn_{0.1}Fe_2O_4$ annealed at 400 and $500{^{\circ}C}$ are 40 and 43 emu/g, respectively. The magnetic anisotropy constant of $Ni_{0.9}Zn_{0.1}Fe_2O_4$ annealed at $300{^{\circ}C}$ were calculated to be 1.6 ${\times}$ $10^6$ ergs/$cm^3$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.4
• /
• pp.295-302
• /
• 2008

This paper examines the design and the performance of a PMA-RSM(permanent-magnet assisted reluctance synchronous motor) for washing machine. A FEM(finite element method) is used to analyze performance and maximum torque characteristic of the proposed PMA-RSM. The designed motor is a combination of salient poles, which is making reluctance torque, and permanent magnet which are located on the air-gap of rotor to get a enough torque during low speed resign. Typical flux barrier type reluctance synchronous motor and the effects of adding magnet into the flux barrier of the rotor of a PMA-RSM are compared and examined. Also the maximum torque point of the reluctance torque by reluctance and reaction torque by magnetic alignment torque, which is in barrier, of the proposed PMS-RSM are derived through simulation. Using this results, the characteristics analysis of a performance, an average torque and a torque ripple of flux barrier RSM and the proposed PMA-RSM are performed through FEM under the saturation effect respectively.

• Journal of the Korean Magnetic Resonance Society
• /
• v.17 no.2
• /
• pp.98-104
• /
• 2013

The ERETIC (Electronic REference To access In vivo Concentrations)2 method is a new qNMR experimental technique to measure analytes based on the signal of the reference compound without additional hardware equipment. In this study, ERETIC2 method was validated, and we sought to identify whether it would be possible to apply this method to a specific compound analysis of metabolites in plant. The $90^{\circ}$ pulse value (P1) and spin-lattice relaxation time ($T_1$) of each compound were measured for ERETIC2. The $9^1H$ of 3-(trimethylsilyl) propionic-2,2,3,3-$d_4$ acid (TSP) was used as a reference peak for ERETIC 2, and then, a suitable solvent and pulse sequence for each compound were selected. Under the NOESY-presat sequence, the relative accuracy error for quantitative analyses of primary metabolites was within the range of 5%, with the exception of glucose, which showed ${\geq}$ 55% error due to saturation. It showed excellent results for the quantification of glucose by using a $30^{\circ}$ pulse sequence, which did not suppress the water peak. In addition, the quantitative accuracy for secondary metabolites was extremely accurate, with an error ${\leq}$5% when considering the purity of the standard sample. The ERETIC2 method showed outstanding linearity, precision, and accuracy.

• Journal of the Korean Magnetics Society
• /
• v.5 no.6
• /
• pp.968-973
• /
• 1995

In order to investigate the annealing effect for RF magnetron sputtered $Ni_{83}Fe_{17}$ thin films, we have studied the spin wave rehaviors by FMR after annealing the samples at $135^{\circ}C,\;225^{\circ}C$ in air and at $160^{\circ}C,\;220^{\circ}C,\;330^{\circ}C,\;390^{\circ}C\;and\;420^{\circ}C$ in argon gas for one hour respectively. In FMR spectra for the films annealed in argon gas and the assputtered film at perpendicular resonance, only odd numrer spin waves are observed. But even numrer spin waves are observed for the film annealed in air at $225^{\circ}C$ recause of the large difference retween both surface magnetic anisotropy. In the case of the sample annealed at $420^{\circ}C$ in argon gas, the spin waves are shifted toward high field, can due to the increase of saturation magnetization during annealing. The spacings retween the spin wave resonance fields are narrowed rapidly, this is thought that the magnetic homogeneity increased in the film after annealing at high temperature.

• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.54-61
• /
• 2019

In this study, a magnetic adsorbent was synthesized by growing ferrite nanoparticles substituted with metals (Me = Co, Mn, Ni) on zeolite 4A for the efficient separation of waste adsorbents present in the solution after the adsorption of Cu(II). The metal ferrite grown on the surface of zeolite was prepared by solvothermal synthesis. Characteristics of the magnetic adsorbent were analyzed by X-ray diffractometer (XRD), scanning electron microscopy (SEM) and physical property measurement system (PPMS). The saturation magnetization of the A type zeolite coated with Co-ferrite (CFZC) was the highest at 5 emu/g and the Cu(II) adsorption performance was also excellent. The adsorption results of Cu(II) on CFZC were well fitted by the Langmuir model at 298 K. Also, the adsorption of Cu(II) on CFZC follows a pseudo-second order kinetic. The Gibbs free energy values (${\Delta}G^0$) ranging from -4.63 to -5.21 kJ/mol indicates that the Cu(II) adsorption is spontaneous in the temeprature range between 298 and 313 K.

• Korean Chemical Engineering Research
• /
• v.61 no.2
• /
• pp.287-295
• /
• 2023

Iron nanoparticles (Fe-NPs) were synthesized employing Lagenaria siceraria (LS) leaf aqueous extract as a reducing and capping medium to remove methylene blue (MB) dye and have antibacterial properties against G-negative (Escherichia coli) and G-positive bacteria (Staphylococcus aureus). The formation of LS-Fe-NPs (Lagenaria-siceraria-iron-nanoparticles) was confirmed by a change in color from pale yellow to dark brown. Characterization techniques, such as particle size analysis (PSA), transmission electron microscopy (TEM) and scanning electron microscopy (SEM), were employed to prove nano spherical particles of size range between 80-100 nm. Phytochemicals and the presence of iron in LS-Fe-NPs nanoparticles were proved by UV-visible spectrophotometry. Further, Fourier transform infrared spectroscopy (FTIR) analysis results confirmed the existence of bioactive molecules in the plants. The magnetic property was analyzed using a vibrating sample magnetometer (VSM), which displayed that the synthesized nanoparticles were superparamagnetic and exhibiting a saturation magnetization of 12.5 emu/g. Synthesized magnetic nanoparticles were used in methylene blue (MB) dye removal through adsorption. About 83% of 100 mg/L MB dye was removed within 120 min at pH 6 with a maximum adsorption capacity of 246.8 mg/g. Antibacterial efficacy of LS-Fe-NPs was screened against G-negative (Escherichia coli) and G-positive bacteria (Staphylococcus aureus), respectively, and found that LS-Fe-NPs were effective against Staphylococcus aureus.