• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1051-1052
• /
• 2007

In this paper, as a clean lift, a maglev(magnetic levitation) clean lift is designed and described. The maglev clean lift, which is superior to conventional lifts in vibration, noise, clean class and speed characteristics, consists of magnets, guide rails, guide rollers, magnet module frame, cage, guidance controller, sensors, etc. As design specifications, the maximum value of vibration is 0.2G, the maximum value of noise is 60dB, and the clean class is #10. The design results for the maglev clean lift are shown and discussed.

• 한국멀티미디어학회논문지
• /
• 제19권2호
• /
• pp.375-385
• /
• 2016

Recently, several implantable hearing aids such as cochlear implant, middle ear implant, etc., which have a module receiving power and signal from outside the body, are frequently used to treat the hearing impaired patients. Most of implantable hearing aids are adopted permanent magnet pairs to couple between internal and external devices for the enhancement of power transmission. Generally, the internal device which containing the magnet in the center of receiving coil is implanted under the skin of human temporal bone. In case of MRI scanning of a patient with the implantable hearing aid, however, homogeneous magnetic fields of the MRI might be interfered by the implanted magnet. For the above reasons, the MR image is degraded by large area of artifact, so that diagnostics are almost impossible in deteriorated region. In this paper, we proposed an external coil system that can reduce the artifact of MR image due to the internal coupling magnet. By finite element analysis estimating area of MR artifact according to varying current and shape of the external coil, optimal coil parameters were extracted. Finally, the effectiveness of the proposed external coil system was verified by confirming the artifact at real MRI scan.

• 한국소음진동공학회논문집
• /
• 제20권4호
• /
• pp.361-372
• /
• 2010

Optical image stabilization is a technique to compensate the image blurring caused by some vibrations of camera at the exposure time. Pitching and yawing of camera are sensitive to the image quality so they are usually compensated by optical image stabilization. Corresponding pitching and yawing of a camera, a lens or the image sensor is translated in two-axis direction and then the optical path of camera is adjusted. In this paper, two-axis OIS actuator for mobile camera module is suggested and designed. The actuator is a voice-coil actuator that uses the electromagnetic force of voice-coil to make compensation motions. And ball bearing is used to reduce friction force. Magnetic attractive force between magnets and yokes acts as a preload and magnet springs. Prototype actuator is fabricated to measure the friction force and to verify the feasibility of the OIS actuator with ball bearing. At last, the actuator is improved in consideration of driving force and friction force. Design of experiments is used for designing the actuator.

• 전기학회논문지
• /
• 제60권12호
• /
• pp.2236-2245
• /
• 2011

This paper deals with the levitation force characteristics of electromagnet for MAGLEV vehicle application. The magnetic flux density distribution and levitation force characteristics of the electromagnet are investigated by means of equivalent magnetic circuit model. Firstly, we defined the aligned and unaligned electromagnet module for the full-electromagnet, and magnetic flux paths are represented for each model including leakage and fringing flux paths. Because of the analysis model contains both the permanent magnet and electromagnet coil, we calculated the airgap magnetic flux density and levitation forces using flux superposition in electromagnetic circuit. The results are validated extensively by comparison with finite element analysis. Moreover, the 1/4 scaled magnetic levitation and propulsion test vehicle has been manufactured and tested in order to verify these predictions. The experimental results confirms the validity of the analytical prediction with equivalent magnetic circuit model for the description of a electromagnet.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.491-494
• /
• 2010

본 논문은 소형 항공용 엔진에 적용되는 영구자석 발전기와 단극 발전기의 특성을 기술한다. 영구자석 발전기는 소형화와 빠른 동특성을 장점으로 갖는데, 빠른 동특성은 전적으로 DC/DC 컨버터의 특성에 따르며, 이러한 컨버터는 부피 및 비용의 증가를 가져온다. 반면, 단극 발전기는 계자권선의 자속제어를 통한 단순한 전압제어가 장점이다. 최근, 전자부하들의 넓은 입력전압 범위와 시스템 효율성 등을 고려해 DC/DC 컨버터 없는 영구자석 발전기가 추천된다.

• Journal of Electrical Engineering and Technology
• /
• 제9권5호
• /
• pp.1614-1622
• /
• 2014

A novel equivalent flux sliding-mode observer (SMO) is proposed for dual three-phase interior permanent magnet synchronous motor (DT-IPMSM) drive system in this paper. The DT-IPMSM has two sets of Y-connected stator three-phase windings spatially shifted by 30 electrical degrees. In this method, the sensorless drive system employs a flux SMO with soft phase-locked loop method for rotor speed and position estimation, not only are low-pass filter and phase compensation module eliminated, but also estimation accuracy is improved. Meanwhile, to get the regulator parameters of current control, the inner current loop is realized using a decoupling and diagonal internal model control algorithm. Experiment results of 2MW-level DT-IPMSM drives system show that the proposed method has good dynamic and static performances.

• 한국표면공학회지
• /
• 제41권3호
• /
• pp.94-101
• /
• 2008

A new convenient magnet array module is designed to investigate effects of magnetic field array on magnetron discharge characteristics. Magnetic field analysis showed good agreement of measured discharge region by a CCD device which has a high quantum efficiency over visible wavelength range. OES (optical emission spectroscopy) showed major emission peaks are from electronic transitions in 400 nm range and 800 nm range. Effects of driving voltage characteristics were analyzed in a point of electron drift trajectories and ionizing collision frequencies. Pulsed dc with a fast rising and falling time was analyzed to have potential to increase ionization collisions by putting a burst of hot electrons and to raise sheath potential. From measured voltage and current waveform, maximum of -1000 V peak was generated with $-400\;V_{rms}$ conditions. Possibility of a properly designed magnetron cathode was shown to be used as a melting device. Cu was successfully melted with power density of a several tens of $W/cm^2$.

• Progress in Superconductivity
• /
• 제14권1호
• /
• pp.60-65
• /
• 2012

A superconductor flywheel energy storage system (SFES) is an electro-mechanical battery which transforms electrical energy into mechanical energy for storage, and vice versa. A 35 kWh class SFES module was designed and constructed as part of a 100kWh/1MW class SFES composed of three 35 kWh class SFES modules. The 35 kWh class SFES is composed of a main frame, superconductor bearings, a composite flywheel, a motor/generator, electro-magnetic bearings, and a permanent magnet bearing. The high energy density composite flywheel is levitated by the permanent magnet bearing and superconductor bearings, while being spun by the motor/generator, and the electro-magnetic bearings are activated while passing through the critical speeds. Each of the main components was designed to provide maximum performance within a space-limited compact frame. The 35 kWh class SFES is designed to store 35 kWh, with a 350 kW charge/discharge capacity, in the 8,000 ~ 12,000 rpm operational speed range.

• 대한기계학회논문집A
• /
• 제35권6호
• /
• pp.599-607
• /
• 2011

본 논문에서는 별도의 외부 격리 구조물이나 추가 모터가 필요 없는 XY 선형 모션 스테이지를 위한 반발력 보상 시스템을 개발하였다. 개발된 시스템은 이동 가능한 마그넷 트랙, 스프링, 추가 질량을 포함한 자체 반발력 보상 구조를 가지고 있으며 이송용 모터 코일과 마그넷 트랙의 상대 위치를 검출할 수 있는 전용 센서를 개발하여 고정밀 추력 및 위치를 제어에 적용하였다. 먼저 반발력 보상 시스템을 모델링하고 모의 시험을 통해 이동 거리, 가속도, 하중, 허용 가능한 장비 크기와 같은 설계 요소를 최적화 하였다. 반발력 보상 시스템이 구비된 XY 모션 스테이지를 제작하였으며, 해당 시스템의 성능을 실험적으로 검증하였다. 실험결과 10m/$s^2$ 가감속 시에 85%의 반발력이 반발력 보상 시스템에 의해 흡수되었다.

• 전력전자학회논문지
• /
• 제22권3호
• /
• pp.240-248
• /
• 2017

This paper describes the development of a powertrain for a 20 kW experimental electric vehicle using a surface-mounted permanent magnet synchronous motor (SPMSM) and its application to a test vehicle. Two 10 kW SPMSMs are used in the powertrain, and two-level inverters are developed by using IGBTs to derive these motors. To control the SPMSM, a control board based on a TMS320F28335 DSP module, which has fast arithmetic function and floating point operator, is used. We develop a 100 V/40 A battery pack, which includes $32{\times}4$ LiFePO4 battery cells using commercial BMS. A commercial on-board charger with 220 V (AC) input and 100 V (DC) and 18 A output is used to charge the battery pack. The performance of the developed vehicle, such as acceleration availability, maximum speed, and maximum power, is estimated based on vehicle dynamics and verified through experiments.