• Korean Journal of Materials Research
• /
• v.28 no.10
• /
• pp.544-550
• /
• 2018

The passivation of AZ91D Mg alloys by plasma anodization requires deliberate choice of process parameters due to the presence of large amounts of structural defects. We study the dependence of pore formation, surface roughness and corrosion resistance on voltage by comparing the direct current (DC) mode and the pulse wave (pulse) mode in which anodization is performed. In the DC plasma anodization mode, the thickness of the electrolytic oxide film of the AZ91D alloy is uneven. In the pulse mode, the thickness is relatively uniform and the formed thin film has a three-layer structure. The pulse mode creates less roughness, uniform thickness and improved corrosion resistance. Thus, the change of power mode from DC to pulse at 150 V decreases the surface roughness (Ra) from $0.9{\mu}m$ to $0.1{\mu}m$ and increases the corrosion resistance in rating number (RN) from 5 to 9.5. Our study shows that an optimal oxide film can be obtained with a pulse voltage of 150 V, which produces an excellent coating on the AZ91D casting alloy.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.206-208
• /
• 1996

Thin films of magnesium oxide(MgO) were deposited on glass substrates by RF magnetron sputtering method. The characteristics of MgO thin films were analyzed as a function of various deposition conditions such as substrate temperature, substrate self-bias, input power and pressure. As the substrate temperature and bias voltage were increased, the grain size of MgO thin film increased. XRD peaks of (111) and (222) direction became dominant, as the substrate bias voltage increases and temperature decreases.

• Korean Journal of Materials Research
• /
• v.29 no.5
• /
• pp.288-296
• /
• 2019

The passivation of AZ91D Mg alloys through plasma anodization depends on several process parameters, such as power mode and electrolyte composition. In this work, we study the dependence of the thickness, composition, pore formation, surface roughness, and corrosion resistance of formed films on the electrolyte temperature at which anodization is performed. The higher the electrolyte temperature, the lower is the surface roughness, the smaller is the oxide thickness, and the better is the corrosion resistance. More specifically, as the electrolyte temperature increases from 10 to $50^{\circ}C$, the surface roughness (Ra) decreases from 0.7 to $0.15{\mu}m$ and the corrosion resistance increases from 3.5 to 9 in terms of rating number in a salt spray test. The temperature increase from 10 to $50^{\circ}C$ also causes an increase in magnesium content in the film from 25 to 63 wt% and a decrease in oxygen from 66 to 21 wt%, indicating dehydration of the film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04a
• /
• pp.133-138
• /
• 2000

MgO thin films were deposited using $Mg(tmhd)_2$ as a precursor dissolved in a solvent by electrostatic spray pyrolysis. When a pure tetra hydro furan was used as a solvent, a large number of particles appeared on the MgO thin film surface due to homogeneous nucleation. However, by adding 1-butyl alcohol or 1-octyl alcohol to THF, homogeneous nucleation was restricted and the number density of the large particles was also drastically reduced. X-ray diffraction analysis showed that the MgO films had a (100) preferred orientation regardless of the type of solvents used. Characterization using Fourier Transformed-Infrared and spectroscopic photometer revealed that the crystallized MgO thin films on the glass substrate had a high optical transmittance (> 85 %) in the visible range. Discharge characteristics of MgO thin films deposited by ESP method on an alternating-current plasma display panel were compared with a MgO thin film prepared by reactive radio-frequency planar magnetron sputtering.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.5
• /
• pp.194-198
• /
• 2015

A blade-abrading method was newly developed for the preparation of clean Mg alloy surface and reported for the first time in detail in this paper. The blade-abrading method includes abrading of the Mg alloy surface with a sharp blade or knife to remove the surface oxide and contaminants on the skin of Mg alloys mechanically, thereby providing very clean surface of Mg alloys. The clean surface prepared by the blade-abrading method in the air was found to be covered with thin and dense air-formed oxide films. Based on the experimental results obtained in this work, it is concluded that the newly developed blade-abrading technique is a very simple and useful pretreatment method which can provide clean and well-defined surface for the following surface treatments.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.2
• /
• pp.354-356
• /
• 2017

We focused on light management technology in amorphous silicon solar cells to suppress increase in absorber thickness for improving power conversion efficiency (PCE). $MgF_2$ and $TiO_2$ anti-reflection layers were coated on both sides of Asahi VU ($glass/SnO_2:F$) substrates, which contributed to increase in PCE from 9.16% to 9.81% at absorber thickness of only 150 nm. Also, we applied very thin $MgF_2$ as a rear reflector at n-type nanocrystalline silicon oxide/Ag interface to boost photocurrent. By reinforcing rear reflection, we could find the PCE increase from 10.08% up to 10.34% based on thin absorber about 200 nm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.697-700
• /
• 2011

Thin-film transistors(TFTs) with magnesium zinc tin oxide(MZTO) channel layer are fabricated by solution-process. The threshold voltage (Vth) shifted toward positive directly with increasing Mg contents in MZTO system. Because the Mg has a lower standard electrode potential (SEP) than Sn, Zn, thus degenerate the oxygen vacancy ($V_O$). As a result, the Mg act as carrier suppressor and oxygen binder in the MZTO as well as a Vth controller.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.523-526
• /
• 2002

This paper presents the simulation of Au / $Ba_{x}$S $r_{1-x}$ Ti $O_3$(BSTO) / Magnesium oxide (MgO) multi-layered and electrically tunable band-pass filters (BPFs) by using high frequency structure simulator (HFSS). This model is a two-pole microstrip edge coupled filter. The filter was designed fur a center frequency about 5.8 GHz. The tunabillity of the filter is achieved using the nonlinear dc electric-field dependence on the relative dielectric constant of BSTO frroelectric thin film. This work seems very promising for future wireless communication systems....

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1732-1734
• /
• 2003

An MgO thin film sputtering system for the PDP (Plasma Display Panel) applications has been developed. This system was manufactured with a vertical In-Line type of 42 inch, which has the length of 520 mm and the width of 900 mm. A reactive magnetron discharge for this sputtering was generated using an unipolar pulsed power supply which has functions of constant voltage (Max. 500 V) and current (Max. 15 A) control, frequency of $10{\sim}100$ kHz and duty ratio of $10{\sim}60$ %. The experiment was conducted under various conditions : $3{\sim}10$ mTorr of pressure, the ratio of $O_2$/Ar = $0.1{\sim}0.5$, 50 % of duty and power of $0.5{\sim}1.7$ kW. From the experiment, the deposition rate of a static state and a moving state were measured to be about 45 nm/min and 6 nm m/min at the distance of 50 mm between the target and the substrate, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.581-584
• /
• 2002

In this work, a CPW resonator was designed and fabricated to investigate the basic microwave properties, such as effective dielectric constant, of BST thin films. Their properties were used as basic data to simulate and design CPW tunable bandpass filter. We also report on gold/$Ba_{0.5}Sr_{0.5}TiO_3$(BST) ferroelectric thin film C-band tunable bandpass filters(BPFs) designed and fabricated on magnesium oxide substrates using CPW structure. The 2 pole filter was designed for a center frequency of 5.88 GHz with a bandwidth of 9 %. The BST based CPW filter offers a high sensitivity parameter as well as a low loss parameter. The tuning range for the bandpass filter with CPW structure was determined to be 170 MHz.