• Magazine of the Korean Society of Agricultural Engineers
• /
• v.26 no.1
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• Archives of design research
• /
• v.2 no.1
• /
• pp.63-97
• /
• 1989

There is nothing more important than the form and function in design, because every design product can be done on the basis of them. Form and Function are already existed before the word of design has been appeared and all the natural and man-made things' basic organization is based on their organic relations. The organic relations is the source of vitality which identifies the subsistance of all the objects and the evolution of living creatures has been changed their appearances by the natural law and order. Design is no exception. Design is a man-made organic thing which is developed its own way according to the purposed aim and given situations. If so, what is the ultimate goal of design. It is without saying that the goal is to make every effort to contribute to the -human beings most desirable life by the designer who is devoting himself to their convenience and well-being. Therefore, the designer can be called the man of rich life practitioner. This word implies a lot of meanings since the essence of design is improving the guality of life by the man-made things which are created by the designer. Also, the things are existed through the relations between form and function, and the things can keep their value when they are answered to the right purpose. In design, thus, it is to be a main concern how to create valuable things and to use them in the right way, and the subject of study is focused on the designer's outlook of value and uk relations between form and function. Christopher Alexander mentioned the importance of form as follows. The ultimate object of design is form. Every design problem begins with an effort to achieve fittness between the form and its context. The form is the solution to the problem: the context defmes the problem. In other words, when we speak of design, the real object of discussion is not form alone, but the ensemble comprising the form and its context. Good fit is a desirable property of this ensemble which relates to some particular division of the ensemble into form and context. Max Bill mainatined how important form is in design. Form represents a self-contained concept, and its embodiment in an object results in that object becoming a work of art. Futhermore, this explains why we use form so freguently in a comparative sense for determining whether one thing is less or more beautiful than another, and why the ideal of absolute beauty is always the standard by which we appraise form, and through form, art itself. Hence form has became synonymous with beauty. On the other hand, Laszlo Moholy-Nagy stated the importance of function as follows. Function means the task an object is designed to fulfill the task instrument is shaping the form. Unfortunately, this principle was not appreciated at the same time but through the endeavors of Frank Lloyd Wright and of the Bauhaus group and its many collegues in Europe, the idea of functionalism became the keynote of the twenites. Functionalism soon became a cheap slogan, however, and its original meaning blurred. It is neccessary to reexamine it in the light of present circumstances. Charles William Eliot expressed his idea on the relations between function and beauty. Beauty often results chiefly from fittness: indeed it is easy to manitain that nothing is fair except what is fit its uses or functions. If the function of the product of a machine be useful and valuable, an the machine be eminently fit for its function, it conspicuously has the beauty of fittness. A locomotive or a steamship has the same sort of beauty, derived from the supreme fittness for its function. As functions vary, so will those beauty..vary. However, it is impossible to study form and function in separate beings. Function can't be existed without form, and without function, form is nothing. In other words, form is a function's container, and function is content in form. It can be said that, therefore, the form and function are indispensable and commensal individuals which have coetemal relations. From the different point of view, sometimes, one is more emphasized than the other, but in this case, the logic is only accepted on the assumption of recognizing the importance of the other's entity. The fact can be proved what Frank Hoyd wright said that form and function are one. In spite of that, the form and function should be considered as independent indivisuals, because they are too important to be treated just as the simple single one. Form and function have flexible properties to the context. In other words, the context plays a role as the barometer to define the form and function, also which implies every meaning of surroun'||'&'||'not;dings. Thus, design is formed under the influence of situations. Situations are dynamic, like the design process itself, in which fixed focus can be cripping. Moreover, situations control over making the good design. Judging from the respect, I defined the good design in my thesis An Analytic Research on Desigh Ethic, "good design is to solve the problem by the most proper way in the situations." Situations are changeable, and so is design. There is no progress without change, but change is not neccessarily progress. It is highly desirable that there changes be beneficial to mankind. Our main problem is to be able to discriminate between that which should be discarded and that which should be kept, built upon, and improved. Form and Function are no exception. The practical function gives birth to the inevitable form and the $$\mu$ti-classified function is delivered to the varieties of form. All of these are depended upon changeable situations. That is precisely the situations of "situation de'||'&'||'not;sign", the concept of moving from the design of things to the design of the circumstances in which things are used. From this point of view, the core of form and function is depended upon how the designer can manage it efficiently in given situations. That is to say that the creativity designer plays an important role to fulfill the purpose. Generally speaking, creativity is the organization of a concept in response to a human need-a solution that is both satisfying and innovative. In order to meet human needs, creative design activities require a special intuitive insight which is set into motion by purposeful imagination. Therefore, creativity is the most essential quality of every designer. In addition, designers share with other creative people a compulsive ingenuity and a passion for imaginative solutions which will meet their criteria for excellence. Ultimately, it is said that the form and function is the matter which belongs to the desire of creative designers who constantly try to bring new thing into being to create new things. In accordance with that the main puppose of this thesis is to catch every meaning of the form and function and to close analyze their relations for the promotion of understanding and devising practical application to gradual progression in design. The thesis is composed of four parts: Introduction, Form, Function and Conclusion. Introduction, the purpose and background of the research are presented. In Chapter I, orgin of form, perception of form, and classification of form are studied. In Chapter II, generation of function, development of function, and diversification of function are considered. Conclusion, some concluding words are mentioned.ioned.

• Korean Journal of Agricultural Science
• /
• v.3 no.1
• /
• pp.95-104
• /
• 1976

This study was conducted to test the harvesting operation of two kinds of rice varieties such as Milyang #15 and Tong-il with a imported two furrow Japanese combine and was performed to find out the operational accuracy of it, the adaptability of this machine, and the feasibility of supplying this machine to rural area in Korea. The results obtained in this study are summarized as follows; 1. The harvesting test of the Milyang #15 was carried out 5 times from the optimum harvesting operation was good regardless of its maturity. The field grain loss ratio and the rate of unthreshed paddy were all about 1 percent. 2. The field grain loss of Tong-il harvested was increased from 5.13% to 10.34% along its maturity as shown in Fig 1. In considering this, it was needed that the combine mechanism should be improved mechanically for harvesting of Tong-il rice variety. 3. The rate of unthreshed paddy of Tong-il rice variety of which stem was short was average 1.6 percent, because the sample combine used in this study was developed on basisof the long stem variety in Japan, therefore some ears owing to the uneven stem of Tong-il rice could nat reach the teeth of the threshing drum. 4. The cracking rates of brown rice depending mostly upon the revolution speed of the threshing drum(240-350 rpm) in harvesting of Tong-il and Milyang #15 were all below 1 percent, and there was no significance between two varieties. 5. Since the ears of Tong-il rice variety covered with its leaves, a lots of trashes was produced, especially when threshed in raw materials, and the cleaning and the trashout mechanisms were clogged with those trashes very often, and so these two mechanisms were needed for being improved. 6. The sample combine of which track pressure was $0.19kg/cm^2$ could drive on the soft ground of which sinking was even 25cm as shown in Fig 3. But in considering the reaping height adjustment, 5cm sinking may be afford to drive the combine on the irregular sinking level ground without any readjustment of the resaping height. 7. The harvesting expenses per ha. by the sample combine of which annual coverage area is 4.7 ha. under conditions that the yearly workable days is 40, percentage of days being good for harvesting operation is 60%, field efficiency is 56%, working speed is 0.273m/sec, and daily workable hours is 8 hrs is reasonable to spread this combine to rural area in Korea, comparing to the expenses by the conventional harvesting expenses, if mechanical improvement is supplemented so as to harvest Tong-il rice. 8. In order to harvest Tong-il rice, the two furrow combine should be needed some mechanical improvements that divider can control not to touch ears of paddy, the space between the feeding chain and the thrshing drum is reduced, trash treatment apparatus must be improved, fore and rear adjust-interval is enlarged, and width of track must be enlarged so as to drive on the soft ground.

• Journal of Fashion Business
• /
• v.13 no.6
• /
• pp.61-75
• /
• 2009

The objective of this research is to the enhance the color function of work clothing : to research and analyze the hue and tone of work clothing colors to be used for machinery and heavy industries in national industrial complexes, Through this research, the color using problems which related with safety workers will be revealed. For this project, total 42 sets of work suits were sampled from 12 different companies in the machinery and construction industries in the national industrial complexes of Gyeongsang Namdo Province and 16 sets of work suits currently being sold in the market. The collected work suits samples were classified according to item types and design. Color measurements were taken thus: After calibration according to ASTM D1729 specifications of standardized configuration settings to match standardized luminous source D65(Daylight 6500K) in color cabinet BOTECK SuperLight-VI, the RGB values of the work suits were calculated using PANTONE Color Cue TX. The RGB values of the colors thus derived were converted into V/C values using the Munsell Conversion 9.0.6 and analyzed with Munsell's 10-color system and PCCS. The results were presented according to Munsell's color wheel and color and brightness distributions were expressed in table form, as well as presented as a tone map. Following analysis, color hue distribution was found to be concentrated around PB, and brightness distribution toward the low end and mid range of the scale. Saturation values were distributed mostly around the low end of the scale. Following color tone analysis according to PCCS, it became apparent that colors were mainly distributed around dkg, ltg, and g, at low- and mid-brightness and low-saturation. Therefore, it may be concluded that colors used in work suits in the machinery and heavy industries are mainly cool colors, at low- and mid-brightness and low saturation. It is conjectured that such colors were applied uniformly in the workplace in order to serve certain functions, such as concealment of stains and contamination. Therefore, it follows that the utilization of colors, among other functions served by working clothings, must be taken into consideration in order to enhance safety and efficiency.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.355-361
• /
• 2006

In large scale environments like airport, museum, large warehouse and department store, autonomous mobile robots will play an important role in security and surveillance tasks. Robotic security guards will give the surveyed information of large scale environments and communicate with human operator with that kind of data such as if there is an object or not and a window is open. Both for visualization of information and as human machine interface for remote control, a 3D model can give much more useful information than the typical 2D maps used in many robotic applications today. It is easier to understandable and makes user feel like being in a location of robot so that user could interact with robot more naturally in a remote circumstance and see structures such as windows and doors that cannot be seen in a 2D model. In this paper we present our simple and easy to use method to obtain a 3D textured model. For expression of reality, we need to integrate the 3D models and real scenes. Most of other cases of 3D modeling method consist of two data acquisition devices. One for getting a 3D model and another for obtaining realistic textures. In this case, the former device would be 2D laser range-finder and the latter device would be common camera. Our algorithm consists of building a measurement-based 2D metric map which is acquired by laser range-finder, texture acquisition/stitching and texture-mapping to corresponding 3D model. The algorithm is implemented with laser sensor for obtaining 2D/3D metric map and two cameras for gathering texture. Our geometric 3D model consists of planes that model the floor and walls. The geometry of the planes is extracted from the 2D metric map data. Textures for the floor and walls are generated from the images captured by two 1394 cameras which have wide Field of View angle. Image stitching and image cutting process is used to generate textured images for corresponding with a 3D model. The algorithm is applied to 2 cases which are corridor and space that has the four wall like room of building. The generated 3D map model of indoor environment is shown with VRML format and can be viewed in a web browser with a VRML plug-in. The proposed algorithm can be applied to 3D model-based remote surveillance system through WWW.

• KIPS Transactions on Computer and Communication Systems
• /
• v.9 no.10
• /
• pp.239-246
• /
• 2020

In the medical field where artificial intelligence technology is introduced, research related to clinical decision support system(CDSS) in relation to diagnosis and prediction is actively being conducted. In particular, medical imaging-based disease diagnosis area applied AI technologies at various products. However, medical imaging data consists of inconsistent data, and it is a reality that it takes considerable time to prepare and use it for research. This paper describes a one-stop AI learning platform for converting to medical image standard R_CDM(Radiology Common Data Model) and supporting AI algorithm development research based on the dataset. To this, the focus is on linking with the existing CDM(common data model) and model the system, including the schema of the medical imaging standard model and report information for multi-center research based on DICOM(Digital Imaging and Communications in Medicine) tag information. And also, we show the execution results based on generated datasets through the AI learning platform. As a proposed platform, it is expected to be used for various image-based artificial intelligence researches.

• The Journal of Korean Academy of Prosthodontics
• /
• v.55 no.3
• /
• pp.264-271
• /
• 2017

Purpose: The purpose of this study is to investigate the differences in bond strength of four different indirect composites to the gold alloy and Ni-Cr alloy according to type of metal surface treatment after water storage. Materials and methods: Type IV gold alloy and Ni-Cr alloy were used for casting alloy while four types of indirect composite resins (Gradia, Tescera Sinfony and in;joy) were used in this study. Metal specimens were produced by casting and total of 240 specimens (60 specimens per one indirect composite group) were prepared. After bonding indirect composite resin and undergoing 24 hours of polymerization, customized jig was attached to the metal specimen and shear bond strength were measured using universal testing machine. Also, differences in shear bond strength before and after water storage for 240 hours were also measured. Results: In the measurement of shear bond strength according to the metal surface treatments, bead group showed high strength followed by loop and flatting group (P<.05). After being stored in water bath for 240 hours, Gradia showed statistically significant high bond strength compared to other indirect composite resins in all groups (P<.05). Conclusion: Shearbond strength was found to be different according to type of metal surface treatment and type of metal used after storage in water. Further studies need to be developed for clinical practices as three are still problems of microleakage, stain or wear.

• Journal of Food Hygiene and Safety
• /
• v.34 no.6
• /
• pp.571-575
• /
• 2019

Fungal occurrence during production of dried red pepper was investigated using red pepper samples collected at harvest, before and after washing, and before, during or after drying. Fungal incidence was evaluated by counting the number of fungal colonies grown after incubating random pepper cuts on potato dextrose agar plates. Washing with ground water had no significant effect on reduction of fungal contamination. Fungal increase was observed in some samples, and the insides of washer and containers were contaminated with fungi. Drying caused significant fungal increase regardless of drying method although the fungal incidence after machine drying was lower than that after greenhouse drying. Fungal increase was observed in the samples being dried in a greenhouse and some mycotoxigenic species were also detected. Therefore, the most important control point for fungal contamination during dried pepper production appears to be the drying process, especially in a greenhouse.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.4
• /
• pp.309-322
• /
• 2007

This study deals with the irradiation effects on some selected components which are being used in an Advanced Spent Fuel Conditioning Process (ACP). Irradiation test components have a higher priority from the aspect of their reliability because their degradation or failure is able to critically affect the performance of an ACP equipment. Components that we chose for the irradiation tests were the AC servo motor, potentiometer, thermocouples, accelerometer and CCD camera. ACP facility has a number of AC servo motors to move the joints of a manipulator and to operate process equipment. Potentiometers are used for a measurement of several joint angles in a manipulator. Thermocouples are used for a temperature measurement in an electrolytic reduction reactor, a vol-oxidation reactor and a molten salt transfer line. An accelerometer is installed in a slitting machine to forecast an incipient failure during a slitting process. A small CCD camera is used for an in-situ vision monitoring between ACP campaigns. We made use of a gamma-irradiation facility with cobalt-60 source for an irradiation test on the above components because gamma rays from among various radioactive rays are the most significant for electric, electronic and robotic components. Irradiation tests were carried out for enough long time for total doses to be over expected threshold values. Other components except the CCD camera showed a very high radiation hardening characteristic. Characteristic changes at different total doses were investigated and threshold values to warrant at least their performance without a deterioration were evaluated as a result of the irradiation tests.

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.57-67
• /
• 2002

The effect of $\beta$-TCP and PHA as additives on initial setting time, compressive strength and surface micro-structure after in vitro test of bone cement in TTCP and DCPA system was investigated. The median particle sizes of TTCP, $\beta$-TCP, DCPA and PHA for bone cement were about 3, 5, 0.9 and 4${\mu}{\textrm}{m}$, respectively. Initial setting time and compressive strength of bone cement with various composition was measured by Vicat test and Universal Testing Machine, and surface morphology and crystalline phases of bone cements were observed and analyzed by SEM and x-ray diffractometer. Initial setting time was not affected by composition but by powder/liquid ratio, and cement with PHA required double amount of solution for paste as much as one without PHA, especially. It was thought that $\beta$-TCP and PHA in bone cements was not related to setting reaction. Thus, the addition of $\beta$-TCP and PHA in bone cements decreased compressive strength and inhabited HAP from being produced on surface in vitro test. In conclusion, it was not expected that $\beta$-TCP and PHA in TTCP-DCPD bone cements enhanced the strength and bioacitivity.