• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.6
• /
• pp.815-824
• /
• 2022

Among the main facilities of the power plant, the circulating water used for cooling the power generation system is supplied through the Circulation Water Intake Basin (CWIB). The vortexes of various types generated in the Pump Sump (PS) of CWIB adversely affect the Circulation Water Pump (CWP) and pipelines. In particular, the free surface vortex accompanied by air intake brings about vibration, noise, cavitation etc. and these are the causes of degradation of CWP performance, damage to pipelines. Then power generation is interrupted by the causes. Therefore, it is necessary to investigate the hydraulic characteristics of CWIB through the hydraulic model experiment and apply an appropriate Anti Vortex Device (AVD) that can control the vortex to enable smooth operation of the power plant. In general, free surface vortex is controlled by Curtain Wall (CW) and the submerged vortex is by the anti vortex device of the curtain wall. The detailed specifications are described in the American National Standard for Pump Intake Design. In this study, the circulating water intake part of the Tripoli West 4×350 MW power plant in Libya was targeted, the actual operating conditions were applied, and the vortex reduction effect of the anti vortex device generated in the suction tank among the circulating water intake part was analyzed through a hydraulic model experiment. In addition, a floor splitter was basically applied to control the submerged vortex, and a new type of column curtain wall was additionally applied to control the vortex generated on the free surface to confirm the effect. As a result of analyzing the hydraulic characteristics by additionally applying the newly developed Column Curtain Wall (CCW) to the existing curtain wall, we have found that the vortex was controlled by forming a uniform flow. In addition, the vortex angle generated in the circulating water pump pipeline was 5° or less, which is the design standard of ANSI/HI 9.8, confirming the stability of the flow.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1201-1208
• /
• 2022

In general, to maximize the supply and efficiency of floating offshore wind power generation energy, the motion caused by wave attenuation of the substructure must be reduced. According to previous studies, the motion response was reduced due to the vortex viscosity generated by the damping plate installed in the lower structure among the waves. In this study, a 5 MW semi-submersible OC5 platform and two platforms with attenuation plates were designed, and free decay experiments and numerical calculations were performed to confirm the effect of reducing motion due to vortex viscosity. As a result of the model test, when the heave free decay tests were conducted at drop heights of 30 mm, 40 mm, and 50 mm, compared with the OC5 platform, the platform with two types of damping plates attached had relatively improved motion damping performance. In the model test and numerical calculation results, the damping plate models, KSNU Plate 1 and KSNU Plate 2, were 1.1 times and 1.3 times lower than OC5, respectively, and the KSNU Plate 2 platform showed about two times better damping performance than OC5. This study shows that the area of the damping plate and the vortex viscosity are closely related to the damping rate of the heave motion.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.21 no.4
• /
• pp.206-216
• /
• 1988

In order to set up a predictive model for effective spat collection of pen shell, Atrina (Servatrina) pectinata, the survival rate and time required at each developmental stage of drifting larvae were surveyed during the period from June 8 to October 16 in 1986 at the Yongku inlet Chilchon Is., Chinhae Bay, the southern part of Korea. And also the experiments of spat collection were carried out In Yongku inlet during the period from July 6 to November 23 in 1987 and In Yoja Bay during the period from July 9 in 1987 to February 15 in 1588. The advent of D-shape larvae ca. $135\times144um $ long had three peaks in that area: August 1, 12 and 25. Umbo shape larvae ca. $300\times317um$ and full grown larvae ca. $455\times450um$ long also sowed three peaks: August 9, August 22 and September 4 for the former, and August 23, September 3 and September 16 for the latter. Nine to ten days was required for D-shape larvae to develop to umbo shape larvae. The instantaneous survival rate was 0.94 with a total survival rate if $54\%$ at this intermorphological stage. The required time of umbo to full grown larvae varied from twelve to fourteen days with a instantaneous survival rate of 0.88 and total survival rate of $19\%$. Twenty-two to twenty-three days was required for each group of the D-shape larvae to reach a fullgrown stage, and their total survival rate was $10\%$ during this developmental period. The number of the spat attached to the spat collector is 0.16 inds. per $m^2$ vertical spat collector in Yongku inlet and 0.48 inds. per $m^2$ horizontal spat collector in Yoja Bay. The average shell length of spat attached was $0.51({\pm}0.15)\;mm$ on September $27,\;38.52({\pm}6.98)\;mm$ on November 21 in 1987 and $49.00({\pm}10.77)mm$ on February 15 in 1988.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.36 no.5
• /
• pp.554-562
• /
• 2007

Ceramide rich intercellular lipid lamellae are thought to be particularly important in maintaining the structural integrity of epidermal barrier. Ceramide is synthesized de novo by serine palmitoyltransferase (SPT) phospholipid intermediates, serine and palmitic acid persist within the stratum corneum. The ceramide which is synthesized is degraded with fatty acid and sphingosine by degradative enzyme ceramidase. The depletion of ceramide in stratum corneum was reported in the atopic dermatitis. As an effort to search for the dietary source for improving the level of ceramide in epidermis, the dietary effects of various-typed silk protein were compared. Seventy male NC/Nga mice, an animal model of atopic dermatitis, were divided into seven groups: group CA as an atopic control with control diet, group S: 1% crude sericin diet, group F: 1% crude fibroin diet, group PS : peptide pattern of sericin(Mw 5000), group PF: peptide pattern of fibroin (Mw 1500), group AS: manufactured the same as amino acid profile of sericin and group AF: manufactured the same as amino acid profile of fibroin. Ten male BALB/c mice were served as group C (control group) control diet. All mice were fed on diet and water ad libitum for 10 weeks. Dry skin condition was established in group CA as ceramide content was decreased. Despite a marked decrease of mRNA and prorein expression of SPT, enzyme do novo synthesis, ceramide content of group S was dramatically increased by inhibiting the mRNA and protein expression of degradative enzyme ceramidase. However, dietary supplementation of crude silk fibroin protein (group F) and in other groups that were supplemented with either amino acid or peptide type of sericin or fibroin did not increase the level of ceramide. Together, our data demonstrate that dietary supplementation of crude sericin is more effective at improving ceramide level in epidemis of NC/Nga mice.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.3
• /
• pp.173-179
• /
• 2019

Cryogenic air separation unit produces various gases such as $N_2$, $O_2$, and Ar by liquefying air. The process also varies with diverse production conditions. The one for SNG production among them has lower efficiency compared to other air separation unit because it requires ultrapure $O_2$ with purity not lower than 99.5%. Among factors that reduce the efficiency of air separation unit, power consumption due to compress air and heat duty of double column were representatives. In this study, simulation of the air separation unit for SNG production was carry out by using ASEPN PLUS. In the results of the simulation, 18.21 kg/s of at least 99.5% pure $O_2$ was produced and 33.26 MW of power was consumed. To improve the energy efficiency of air separation unit for SNG production, the sensitivity analysis for power consumption, purities and flow rate of $N_2$, $O_2$ production in the air separation unit was performed by change of air boosting ratios. The simulated model has three types of air with different pressure levels and two air boosting ratio. The air boosting ratio means flow rate ratio of air by recompressing in the process. As increasing the first air boosting ratio, $N_2$ flow rate which has purity of 99.9 mol% over increase and $O_2$ flow rate and purity decrease. As increasing the second air boosting ratio, $N_2$ flow rate which has purity of 99.9 mol% over decreases and $O_2$ flow rate increases but the purity of $O_2$ decreases. In addition, power consumption of compressing to increase in the two cases but results of heat duty in double column were different. The heat duty in double column decreases as increasing the first air boosting ratio but increases as increasing the second air boosting ratio. According to the results of the sensitivity analysis, the optimum air boosting ratios were 0.48 and 0.50 respectively and after adjusting the air boosting ratios, power consumption decreased by approximately 7% from $0.51kWh/O_2kg$ to $0.47kWh/O_2kg$.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.5
• /
• pp.479-487
• /
• 2023

Recently, the destructive power of typhoons is continuously increasing owing to global warming. In a situation where the installation of floating wind turbines is increasing worldwide, concerns about the huge loss and collapse of floating offshore wind turbines owing to strong typhoons are deepening. A new type of disconnectable mooring system must be developed for the safe operation of floating offshore wind turbines. A new submersible mooring pulley considered in this study is devised to more easily attach or detach the floating of shore wind turbine with mooring lines compared with other disconnectable mooring apparatuses. To investigate the structural safety of the initial design of submersible mooring pulley that can be applied to an 8MW-class floating type offshore wind turbine, scale-down structural models were developed using a 3-D printer and structural tests were performed on the models. For the structural tests of the scale-down models, tensile specimens of acrylonitrile butadiene styrene material that was used in the 3-D printing were prepared, and the material properties were evaluated by conducting the tensile tests. The finite element analysis (FEA) of submersible mooring pulley was performed by applying the material properties obtained from the tensile tests and the same load and boundary conditions as in the scale-down model structural tests. Through the FEA, the structural weak parts on the submersible mooring pulley were reviewed. The structural model tests were conducted considering the main load conditions of submersible mooring pulley, and the FEA and test results were compared for the locations that exceeded the maximum tensile stress of the material. The results of the FEA and structural model tests indicated that the connection structure of the body and the wheel was weak in operating conditions and that of the body and the chain stopper was weak in mooring conditions. The results of this study enabled to experimentally verify the structural safety of the initial design of submersible mooring pulley. The study results can be usefully used to improve the structural strength of submersible mooring pulley in a detailed design stage.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.1
• /
• pp.1-8
• /
• 2015

Wind power systems have gained much attention due to the relatively high reliability, good infrastructures and cost competitiveness to the fossil fuels. Advances have been made to increase the power efficiency of wind turbines while less attention has been focused on structural integrity assessment of structural sub-systems such as towers and foundations. Among many parameters for integrity assessment, the most perceptive parameter may be the induced horizontal displacement at the hub height although it is very difficult to measure particularly in large-scale and high-rise wind turbine structures. This study proposes an indirect displacement estimation scheme based on the combined use of inclinometers and accelerometers for more convenient and cost-effective measurements. To this end, (1) the formulation for data fusion of inclination and acceleration responses was presented and (2) the proposed method was numerically validated on an NREL 5 MW wind turbine model. The numerical analysis was carried out to investigate the performance of the propose method according to the number of sensors, the resolution and the available sampling rate of the inclinometers to be used.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.3
• /
• pp.257-266
• /
• 2015

This study introduce that we studied optimization and possibility of smoke spread prevention with air-curtain system in undersea tunnel named from Ho-Nam to Jeju line in domestic if a fire break out in train. To verify performance, air-curtain system is installed between rescue station platform and each door of passenger car to provide safety route to evacuator and we studied simulation model of various cases about 15 MW fire severity considering domestic specifications. As a result we verified the fact that CASE1(air jet with 15degree toward passenger car) and CASE 5 (air jet with 15degree toward passenger car and pressure air blast from cross passage) is best Smoke Spread Prevention and less inflow carbon monoxide. Through above results, we expect that air-curtain system is one of the facilities for fire safety and provide us safety platform route in undersea tunnel.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.7
• /
• pp.649-655
• /
• 2010

This study investigated the degradation of phenol using sonication and/or UV-C. The effects of frequency, temperature, pH in solution, argon purging, with UV intensity were estimated in sonication-only, UV-only, and the combined reaction of sonication with UV. The optimum condition for degrading phenol in the sonication-only reaction was 35 kHz, $5^{\circ}C$, and pH 4. As this condition approximately 30% degradation of phenol was achieved within 360 min. However, phenol in the UV-only at $19.3\;mw/cm^2$ under the same condition was completely degraded within 60 min. In the combined system of sonication with UV, the degradation of phenol was well fitted to first-order rate model, and phenol was completely degraded within 360 min and 45 min at UV intensity of $7.6\;mW/cm^2$($17.3{\times}10^{-3}\;min^{-1}$) and $19.3\;mW/cm^2$($138.1{\times}10^{-3}\;min^{-1}$), respectively. Adding methanol, as a radical scavenger, in the phenol degradation in the sonication reaction indicates that OH radical is a major factor in the degradation of phenol. The order of degradation efficiencies of phenol was in the order of as follows; combined reaction of sonication with UV > UV-only > sonication-only.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.05a
• /
• pp.79-86
• /
• 2005

The apparent source spectrum of the Fukuoka earthquake is estimated at the seismic basement by removing from the observed spectra at Korean seismic stations the path and site responses that were previously revealed through inversion process applied to large spectral D/B accumulated until 2004. The approximate source spectrum is also estimated by using data recorded near the epicenter from various Japanese seismic networks and compared with the Korean source spectrum. The comparison result shows that there is good agreement among source spectra estimated based on the data from seismic networks of Korea at large distances (190km