• Korean Journal of Materials Research
• /
• v.7 no.4
• /
• pp.303-309
• /
• 1997

기존의 전자 기판에서 땜납으로 사용되고 있는 Sn-Pb계 합금을 대체하기 위한 새로운 합금을 개발하기 위하여 열역학을 이용한 상평형계산을 통해 얻은 다원계 상태도를 바탕으로 적정한 녹는점과 용융구간을 가지는 Sn-Bi-In-Zn계 솔더합금을 설계하였다. 설계된 합금을 제작하여 XRD, DSC및 EDX로 분석하여 상의 확인,조성분석 및 고상점과 액상점 등의 녹음 거동을 확인하였다. 또한 열처리에 따른 미세구조의 변화를 관찰하였고, 이러한 조직변화가 기계적 성질에 미치는 영향을 경도실험과 인장실험을 통해 연구하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.9
• /
• pp.1851-1857
• /
• 2009

In this paper, reuse module generation algorithm consider the power consumption for FPGA technology mapping is proposed. To proposed algorithm is RT library generating algorithm consider power consumption for reuse module using FPGA technology mapping. In the first, selected FPGA for power consumption calculation. Technology mapping process have minimum total power consumption consider LUT's constraint in selected FPGA. A circuit into device by selected proper modules of allocation result for power consumption constraint using data.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.1
• /
• pp.7-11
• /
• 2001

We measured the electron transport coefficients, the electron drift velocity, W, and the longitudinal diffusion coefficient, $D_{L}$, over the E/N range from 0.03 to 100 Td and gas pressure range from 0.133 to 122 kPa in the 0.526% and 5.05% $C_{3}F_{8}$-Ar mixtures by the double shutter drift tube with variable drift distance. And we calculated these electron transport coefficients by using multi-term approximation of Boltzmann equation analysis. We determined the electron collision cross sections set for $C_{3}F_{8}$ molecule by the comparison of measurement and calculation. Our special attention in the present study was focused upon the inelastic collision cross sections of the $C_{3}F_{8}$ molecule.

• Transactions of Materials Processing
• /
• v.17 no.7
• /
• pp.507-510
• /
• 2008

Effect of V addition on the precipitation behavior and strength of Fe-36Ni based high strength Invar alloy for power transmission wire was investigated. Fe-36Ni Invar alloy plates were fabricated using conventional ingot casting followed by hot rolling. High strength can be obtained through precipitation hardening and strain hardening by cold rolling. Simulation using FactSage$^{(R)}$ revealed that equilibrium phases which can be formed are two kinds of MC-type precipitates, $Mo_{2}C$ and $M_{23}C_6$ carbide. The latter stoichiometric carbide was expected to be formed at relatively lower temperature of $800^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.474-477
• /
• 2004

This paper deals with a design experience of Control Element Drive Mechanism (CEDM) that is used to withdraw or insert control rods in nuclear reactor. The design is carried out to satisfy the performance requirements for CEDM that were given to ensure reliable and secure actions of the rods. The electrical parameters for four coils that energize the mechanical actuators in CEDM are determined first, Then a computer simulation for CEDM with these coils is performed to see how it works. An adjustment of the coil parameters is made from the simulation results. Finally, it is shown that our final design is valid to guarantee the required performance since the FEM(finite Element Method) calculation shows sufficient vertical attraction forces of a lift armature and a latch magnet, and good dynamics with a full load.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.5
• /
• pp.475-481
• /
• 2009

Real-coded genetic algorithm(RCGA) has better performances than conventional genetic algorithm about dealing with a large domain, the precision and the constrain problem. Also the RCGA has advantage of operation time because it doesn't have to following about decoding operation. In this paper the ranges of PID gains are limited based on Ziegler-Nichols method to consider a long operation time problem that is the main problem of genetic algorithm. Result shows proposed method represents better performance without ignored about result of ZN tuning method and reduces the calculation time.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.250-252
• /
• 2006

In this paper, we studied for the measurement system for on-line testing and evaluation of tilting train express(TTX). The measurement system is installed in each train for the performance measurement during the test run. It is composed of software part, hardware part and can measure various signals such as velocity, voltage, temperature. The software controls the hardware of the measurement system, performs the analysis and calculation of measurement data and acts as interface between users and the system hardware. The hardware is consisted of 7 DAMs(Data Acquisition Modules) and 6 monitoring modules.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.116-119
• /
• 2004

The use of higher strength materials frequently requires the change of design provisions. Following to the previous researches, high strength reinforcing bars have a weak point about the development and splice length. Based on the previous research about high relative rib area, bond strength between reinforcing bars and concrete can be improved by the control of rib height and spacing. But, the code provisions do not include these specific shape of reinforcing bars. So, the purpose of this paper is to determine the effect of relative rib area to the bond strength. This paper describes the experiment and analysis of 5 beam-spliced specimens containing D25 with relative rib areas ranging from 0.073 to 0.17. The test results are also analyzed to make a design formula about the calculation of splice length on the consideration of relative rib area.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.12
• /
• pp.2181-2186
• /
• 2006

In this paper, a RTL binding technique for CPLD constraint is proposed. Allocation processing selected module consider the module calculation after scheduling process for circuit by HDL. Select CPLD for constrain after allocation. A Boolean equation is partitioned for CLB by allocated modules. The proposed binding algorithm is description using optimum CLB within a CPLD. The proposed algorithm is examined by using 16 bit FIR filter. In the case that applicate the algorithm, the experiments results show reduction in used CLB.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.6
• /
• pp.1163-1169
• /
• 2004

An unstructured mathematical model is presented for lactic acid fermentation based on the energy balance. The proposed model reflects the energy metabolic state and then predicts the cell growth, lactic acid production, and glucose consumption rates by relating the above rates with the energy metabolic rate. Fermentation experiments were conducted under various initial lactic acid concentrations of 0, 30, 50, 70, and 90 g/l. Also, a genetic algorithm was used for further optimization of the model parameters and included the operations of coding, initialization, hybridization, mutation, decoding, fitness calculation, selection, and reproduction exerted on individuals (or chromosomes) in a population. The simulation results showed a good fit between the model prediction and the experimental data. The genetic algorithm proved to be useful for model parameter optimization, suggesting wider applications in the field of biological engineering.