• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.639-646
• /
• 2000

Hot air heater with light oil combustion is the most common heater for greenhouse heating in the winter season in Korea. However, since the heat efficiency of the heater is about 80%, considerable unused heat in the form of exhaust gas heat discharges to atmosphere. In order to capture this exhaust gas heat a heat recovery system for plant bed heating in the greenhouse was built and tested in the hot air heating system of greenhouse. The system consists of a heat exchanger made of copper pipes, ${\phi}\;12.7{\times}0.7t$ located inside the rectangular column of $330{\times}330{\times}900mm$, a water circulation pump, circulation plastic pipe and a water tame The total heat exchanger area is $1.5m^2$, calculated considering the heat exchange amount between flue gas and water circulated in the copper pipes. The system was attached to the exhaust gas path. The heat recovery system was designed as to even recapture the latent heat of flue gas when exposing to low temperature water in the heat exchanger. According to performance test it can recover 45,200 to 51,000kJ/hr depending on the water circulation rates of 330 to $690{\ell}$/hr from the waste heat discharged. The exhaust gas temperature left from the heat exchanger dropped to $100^{circ}C$ from $270^{circ}C$ by the heat exchange between the water and the flue gas, while water gained the difference and temperature increased to $38^{circ}C$ from $21^{circ}C$ at the water flow rate of $690{\ell}$/hr. And, the condensed water amount varies from 16 to $43m{\ell}$ at the same water circulation rates. This condensing heat recovery system can reduce boiler fuel consumption amount in a day by 34% according to the feasibility study of the actual mimitomato greenhouse. No combustion load was observed in the hot air heater.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.1038-1042
• /
• 1998

Mechanical grinding and subsequent annealing were applied to the $Nd_5Pr_7Fe_{82}B_6$ and $Nd_{12}Fe_{82}B_6$ ingots, and the crystal structure and magnetic properties were investigated. After 330 hours milling, the particles with $2~3\mu\textrm{m}$average size were identified to be composed of very fine crystallites judging from the x-ray diffraction patterns. The intrinsic coercivity of 18.36 ~ 18.79 kOe and the maximum energy product of 8.32-8.38 MGOe were obtained by the annealing of the milled powders at $600^{\circ}C$ for 2 hours. Annealing at a higher temperature resulted in the improved magnetic properties. However it was revealed that the control of the micro-crystallites formed during the grinding process was more important to get an optimized magnetic properties than the annealing condition.

• Korean Journal of Veterinary Service
• /
• v.24 no.4
• /
• pp.359-367
• /
• 2001

A serological survey was performed to establish basic data for the prevalence of antibodies to some major diseases of domesticated boar serum samples from January to December 2000. Sera collected in breeding farms in Gyeongbuk province were tested for Aujeszky's disease virus(ADV), Porcine reproductive and respiratory syndrome virus(PRRSV), Porcine parvovirus(PPV), Japanese encephalitis virus (JEV), Bordetella bronchiseptica(B bronchiseptica), Mycoplasma ; APP), Toxoplasma, and Brucella. There was no antibody to ADV in domesticated boars serum samples detected by Anti-ADV-gpI assay kit. Sero-positive samples to PRRS by IFA were 0.9%(3/330) The HI titers to PPV ranged variously from less than 10 to over 1,280. Two hundred ninety-four out of 330 tested sera showed HI titer of less than 10. In HI test to JEV, 90.3% of the sera (298/330) were below 10. The majority of the serum samples had low prevalence of the antibody B bronchiseptica. ELISA titers to M hyopneumoniae ranged variously from $\leq$ 10 to $\geq$ 1,280. Antibody titers to A pleuropneumoniae type 2(APP2) and type 5(APP5) were 58.2% and 52.7%, respectively, and the tested samples showing ELISA antibody titers of less than 20. There was no significant geographical difference between APP2 and APP5 in this study. In the antibody test of Toxoplasma, 11.5%(38/330) were positive and samples were all negative in sera test of Brucella.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.793-796
• /
• 2008

Recently early strength concrete has been required for economical assurance and the prevention of frost damage in winter through air reduction in construction of concrete structures. This study presented the optimum condition revealing compressive strength 5MPa which has the possibility of removal of form in 24 hours, and researched the changes of unit weight of cement types of high early strength AE water reducing agents, characteristic of compressive strength expression as cure temperature conditions and slump or airspace. Test results showed at $15^{\circ}C$ with compressive strength of 5MPa that premature removal of form was possible in case of using highly early strength PC water reducing agent with unit weight of cement 360 ; 22hours faster than 10, unit weight 360 ; 20hours faster than 7, unit weight 390 ; 18 hours faster than 4 comparing with OP water reducing agent. And at $5^{\circ}C$ in case of using highly early strength PC water reducing agent with unit weight of cement 330 ; 32hours faster than 10, unit weight 360 ; 30hours faster than 7, unit weight390 ; 27hours faster than 4 comparing with OP water reducing agent. Therefore as the temperature rises $10^{\circ}C$, compressive strength of 5MPa reaching hour shortens 10 hours.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.329-330
• /
• 2008

• Asian-Australasian Journal of Animal Sciences
• /
• v.2 no.3
• /
• pp.329-330
• /
• 1989

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.329-330
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.329-330
• /
• 2011

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.329-330
• /
• 2010

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.11
• /
• pp.907-913
• /
• 2017

The performance of a spark jet driven by pulsed-arc plasma was investigated experimentally for various energy input. A high-speed jet (about 330 m/s) was obtained by rapid gas heating produced by 37 mJ of deposited energy per pulse. The peak velocity and penetration distance of the jet were proportional to the deposited power and the deposited energy per pulse, respectively. A smaller orifice diameter produces a higher velocity jet at lower energy levels. For the same deposited energy, higher-current pulses produce a higher jet velocity than higher-pulse-width pulses. A total deposited energy of about 10 mJ per pulse with a pulse duration of about $10{\mu}s$ was found to be the optimum for energy- efficient operation.