• 대한치과보철학회지
• /
• 제31권3호
• /
• pp.423-446
• /
• 1993

Titanium and its alloys are finding increasing use in medical devices and dental implants. The strong selling point of titanium is its resistance to the highly corrosive body fluids in which an implant must survive. This corrosion resistance is due to a tenacious passive oxide or film which exists on the metal's surface and renders it passive. Potentiodynamic polarization measurement is one of the most commonly used electro-chemical methods that have been applied to measure corrosion rates. And the potentiodynamic polarization test supplies detailed information such as open circuit, rupture, and passivation potential. Furthermore, it indicates the passive range and sensitivity to pitting corrosion. This study was designed to compare the corrosion resistance of the commonly used dental implant materials such as CP Ti, Ti-6A1-4V, Co-Cr-Mo alloy, and 316L stainless steel. And the effects of galvanic couples between titanium and the dental alloys were assessed for their useful-ness-as. materials for superstructure. The working electrode is the specimen , the reference electrode is a saturated calomel electrode (SCE), and the counter electrode is made of carbon. In $N_2-saturated$ 0.9% NaCl solutions, the potential scanning was performed starting from -800mV (SCE) and the scan rate was 1 mV/sec. At least three different polarization measurements were carried out for each material on separate specimen. The galvanic corrosion measurements were conducted in the zero-shunt ammeter with an implant supraconstruction surface ratio of 1:1. The contact current density was recorded over a 24-hour period. The results were as follows : 1. In potential-time curve, all specimens became increasingly more noble after immersion in the test solution and reached between -70mV and 50mV (SCE) respectively after 12 hours. 2. The Ti and Ti alloy in the saline solution were most resistant to corrosion. They showed the typical passive behavior which was exhibited over the entire experimental range. Therefore no breakdown potentials were observed. 3. Comparing the rupture potentials, Ti and Ti alloy had the high(:st value (because their break-down potentials were not observed in this study potential range ) followed by Co-Cr-Mo alloy and stainless steel (316L). So , the corrosion resistance of titanium was cecellent, Co-Cr-Mo alloy slightly inferior and stainless steel (316L) much less. 4. The contact current density sinks faster than any other galvanic couple in the case of Ti/gold alloy. 5. Ag-Pd alloy coupled with Ti yielded high current density in the early stage. Furthermore, Ti became anodic. 6. Ti/Ni-Cr alloy showed a relatively high galvanic current and a tendency to increase.

• Journal of the Optical Society of Korea
• /
• 제9권3호
• /
• pp.119-122
• /
• 2005

Silica-based $2\times2$ thermo-optic (TO) switch using the MMI couplers which have a large fabrication tolerance of 110 (${\mu}m$ were fabricated and operated. Important features of the proposed switch are shown to be a polarization dependency loss of 0.1dB, an extinction ratio of 32.7dB, and a power consumption of 202.8mW.

• Bulletin of the Korean Chemical Society
• /
• 제7권2호
• /
• pp.97-99
• /
• 1986

Calculated ionization potential, electron affinity, electron density and bond order of some thiophene derivatives have been obtained and correlated with the inhibition of corrosion produced by these substances as evaluated by polarization curves. It is apparent that such quantities as the electron density or ionization potential play an important role. The calculation was carried out by the Extended Huckel method for the series of substituted thiophene derivatives.

• 대한화학회지
• /
• 제52권2호
• /
• pp.124-132
• /
• 2008

H3SO4(M: 몰농도) 용액에서 탄소강의 부식방지제로 Furfural hydrazone 유도체의 효과를 질량손실법 및 정전류극성법을 사용해 연구하였다. 이들 유도체 존재하에서 탄소강의 부식속도가 급격히 감소함을 관찰하였다. 이 연구로부터 부식방지효율은 부식방지제 농도가 증가함에 따라 증가하였고 I와 SCN을 첨가하면 부식방지효율은 더욱 증가되었다. 질량손실법을 사용해 5×10-6 M의 유도체가 있을 때와 없을 때 30-60oC 사이에서 탄소강 부식에 미치는 온도 효과를 보았다. 부식과정에 대한 활성화에너지(Ea*)와 다른 열역학적 변수들을 계산하였고 이들에 대해 논의하였다. 정전류극성법을 통해 유도체들이 혼합형 방지제로 작용함을 알았고 외부전류를 흘려주었을 때 음극은 더욱 분극되었다. 3M H3SO4 용액에서 탄소강 표면에 이들 유도체들의 흡착은 Frumkin의 흡착등온을 따랐다. 이들 유도체들의 화학구조를 통해 부식방지 메커니즘을 설명하였다.

• 한국광학회지
• /
• 제32권3호
• /
• pp.120-125
• /
• 2021

본 연구에서는 다파장 빔결합을 위한 master oscillator power amplifier (MOPA) 구조의 선편광 고출력 이터븀 첨가 광섬유 레이저를 개발하였다. 유도 브릴루앙 산란(stimulated Brillouin scattering, SBS)을 억제하기 위하여 pseudo-random binary sequence (PRBS) 신호로 위상 변조 및 비트길이를 최적화한 선폭 약 10 GHz의 시드 레이저를 구현하였으며, 이를 이용하여 3단 증폭을 하였다. 주 증폭단에서는 모드 불안정성 현상(mode instability, MI)의 문턱값을 높이기 위하여 코어 및 클래딩의 직경이 각각 20 ㎛, 40 ㎛인 편광유지(polarization maintaining, PM) 이터븀 첨가 광섬유를 이용하고 지름이 약 9-12 cm인 나선형 홈에 적용하였다. 그 결과, 입사된 여기광 대비 기울기 효율이 83.7%인 1.004 kW의 레이저 출력을 얻었다. 또한, 빔품질(M²)과 편광소광율(polarization extinction ratio, PER)은 각각 1.12와 21.5 dB로 측정되었다. 더욱이, 역방향 스펙트럼의 레일리 신호와 SBS 신호의 첨두 세기 비율은 2.36 dB로 관측되어, SBS가 완화된 레이저 구현을 확인하였다. 또한 증폭 출력에 따라 기울기 효율 및 빔품질의 저하가 없어 모드불안정이 발생하지 않음을 확인하였다.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2003년도 추계학술대회 발표 논문집
• /
• pp.163-168
• /
• 2003

In the present study, the piezoelectricity and polarization of multilayer ceramic actuator, being designed to stack PMN-PZ-PT ceramic layers and Ag-Pd electrode layers alternatively, were investigated under a consideration of geometric factor, the volume ratio of the ceramic to the electrode layers. The actuators were fabricated by tape casting of $0.2Pb(Mg_{1/3}Nb_{2/3)O_3-0.38PbZrO_3-0,42PbTiO_3$ followed by lamination and burnout & co-firing processes. The actuators of $10\times10\times0.6~2\textrm{mm}^3$ in size were formed in a way that $60 ~ 200\mu\textrm{m}$ thick were stacked alternatively with $5\mu\textrm{m}$ thick electrode layer. Increases in polarization and electric field-induced displacement with thickness of the ceramic layer were attributed to change of $90^{\circ}$/$180^{\circ}$ domain ratio, which was affected by interlayer internal stress. The piezoelectricity and actuation behaviors were found to depend upon the volume ratio (or thickness ratio) of ceramic to electrode layers.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.558-566
• /
• 2009

The alloying effect of a small amount of nickel on low alloy steel for application to flue gas desulfurization(FGD) systems was studied. The structural characteristics of the rust layer were investigated by scanning electron microscopy(SEM). The electrochemical properties were examined by means of potentiostatic polarization test, potentiodynamic polarization test, and electrochemical impedance spectroscopy(EIS) in a modified green death solution of 16.9 vol.% $H_2SO_4$+0.35 vol.% HCl at $60^{\circ}C$ and an acid rain solution of $6.25{\times}10^{-5}M\;H_2SO_4+5.5{\times}10^{-3}M\;NaCl$ at room temperature. It was found that as the amount of nickel increased, the corrosion rate increased in the modified green death solution, which seemed to result from micro-galvanic corrosion between NiS and alloy matrix. In acid rain solution, the corrosion rate decreased as the amount of nickel increased due to the repulsive force of $NiFe_2O_4$ rust against $Cl^-$ ions by electronegativity.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제42권
• /
• pp.23.1-23.11
• /
• 2020

Background: 4-Hexylresorcinol (4HR) is able to increase angiogenesis. However, its molecular mechanism in the human endothelial cells has not been clarified. Methods: As endothelial cells are important in angiogenesis, we treated the human umbilical vein endothelial cells (HUVECs) with 4HR and investigated protein expressional changes by immunoprecipitation high-performance liquid chromatography (IP-HPLC) using 96 antisera. Results: Here, we found that 4HR upregulated transforming growth factor-β (TGF-β)/SMAD/vascular endothelial growth factor (VEGF) signaling, RAF-B/ERK and p38 signaling, and M2 macrophage polarization pathways. 4HR also increased expression of caspases and subsequent cellular apoptosis. Mechanistically, 4HR increased TGF-β1 production and subsequent activation of SMADs/VEGFs, RAF-B/ERK and p38 signaling, and M2 macrophage polarization. Conclusion: Collectively, 4HR activates TGF-β/SMAD/VEGF signaling in endothelial cells and induced vascular regeneration and remodeling for wound healing.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2000년도 하계학술발표회
• /
• pp.28-29
• /
• 2000

Optical power splitters and/or couplers are important components for optical signal distribution between channels both in wavelength division multiplexing(WDM) systems and photonic integrated circuits(PICs). Since polarization is usually not known after propagation in an optical fiber, passive WDM components have to be polarization insensitivity, Compared to alternatives such as directional couplers or Y-junction splitters, splitters based on multimode interference(MMI) have found a growing interest in recent yens because of their desirable characteristics, such as compact size, low excess loss, wide bandwidth, polarization independence, and relaxed fabrication tolerances$^{(1)}$ . These devices have been fabricated in polymers, silica, or III-V semiconductor materials. A1 $\times$ 4 MMI power splitter on InP materials that were suitable for application in the 1.55-${\mu}{\textrm}{m}$ region$^{(2)}$ . However, the fabrication process of the structure is too complicated and the photolithography tolerance is very tight. Also, a 1 $\times$ 16 InGaAsP/InP MMI power splitter with an excess loss of 2.2dB and a splitting ratio of 1.5dB was demonstrated by using deep etching$^{(3)}$ . The deep etching of the sidewalls through the entire guide layer of the slab waveguide resulted in a number of drawbacks$^{(4)}$ . (omitted)

• Restorative Dentistry and Endodontics
• /
• 제19권2호
• /
• pp.534-548
• /
• 1994

The purpose of this study is to observe the corrosion characteristics of seven dental amalgams (CAULK FINE CUT, CAULK SPHERICAL, OPTALLOY II, DISPERSALLOY, HI VERALOY, TYTIN, VALIANT) through the anodic polarization curve obtained by using a potentiostat. After each amalgam alloy and Hg being triturated, the triturated mass was inserted into the cylindrical metal mold, and condensed by hydrolic pressure(160 kg/$cm^2$). Each specimen was removed from the metal mold. 24 hours after condensation, specimens were polished with the emery paper and stored at room temperature for 1 week. The anodic polarization curves were employed to compare the corrosion behaviours of the amalgam in 0.9% saline solution, Fusayama's artificial saliva, and stimulated parotid saliva at $37^{\circ}C$ with 3-electrode potentiostat. After the immersion of specimen in electrolyte for 1 hour, the potential scan was begun. The potential scan range was. -1700m V ~ + 400m V(vs. S. C. E) in the working electrode and the scan rate was 50m V /sec. The results were as follows, 1. The corrosion potential, the potential of anodic current peak, and transpassive potential in the stimulated parotid saliva shifted to more anodic direction than those in saline solution, and the current density in the stimulated parotid saliva was lower than that in saline solution. Those in Fusayama's artificial saliva was similar to those in stimulated parotid saliva. 2. The anodic polarization profiles in Fusayama's artificial saliva and stimulated parotid saliva indicated a region of slow slope current density, which is extending from the corrosion potential to the potential of anodic current peak, but that in 0.9% saline solution indicated no region of slow slope. 3. The corrosion potentials for CAULK FINE CUT, CAULK SPHERICAL, and OPT ALLOY II had the similarity in 0.9% saline solution, Fusayama's artificial saliva and stimulated parotid saliva, but those for high coper amalgam and VALIANT had no similarity. 4. The current density for TYTIN amalgam in stimulated parotid saliva was the lowest among the others. 5. As for current density, there was no significant difference between palladium enriched VALINAT and other high copper amalgams.